- DL manuals
- Eagle
- Sonar
- Fish ID 128
- Installation And Operation Instructions Manual
Eagle Fish ID 128 Installation And Operation Instructions Manual
Summary of Fish ID 128
Page 1
1 ® fish id 128 fish id 128 fish id 128 fish id 128 fish id 128 inst inst inst inst installa alla alla alla allation and opera tion and opera tion and opera tion and opera tion and operation tion tion tion tion instr instr instr instr instructions uctions uctions uctions uctions fish id 128.
Page 2
2 eagle electronics po box 669 catoosa, ok 74015 table of contents table of contents table of contents table of contents table of contents introduction .............................................................................................. 3 specifications .......................................
Page 3
3 specifications dimensions ...................... 5.9" w x 5.35" h x 3.4" d input voltage .................... 10 - 15 vdc current drain ................... 150 ma (lights off) ........................... 250 ma (lights on) transmitter frequency .......... 192 khz output power ..... 275 watts (peak...
Page 4
4 installation - bracket you can install the unit on the top of a dash or from an overhead with the supplied bracket. It can also be installed in the dash with an optional ida- 3 or ida-4 mounting kit. If you use the supplied bracket, you may be interested in the optional gbsa-1 swivel bracket kit. ...
Page 5: Location - General
5 permanent mount transducer installation the hs-wspc supplied with your sonar is a transom mount transducer. It can be installed on any outboard or stern-drive (inboard\outboard) powered boat. The “kick-up” mounting bracket helps prevent damage if the transducer strikes an object while the boat is ...
Page 6
6 4. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wiring, bilge pumps, and areators can be displayed on the sonar’s screen. Use caution when routing the trans- ducer cable around these wires. 2. Slide the transducer between the two ratchets...
Page 7
7 ratchets nut metal washer rubber washers metal washer bolt remove the transducer and ratchets from the bracket. Place the ratch- ets into the holes in the bracket with the letter “b” aligned with the dot stamped in the bracket. Reassemble the transducer and bracket and place them against the trans...
Page 8
8 4. Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The bottom of the transducer bracket should be in line with the bottom of the hull. Don't let the bracket extend below the hull! Mark the center of the slots for the mounting h...
Page 9: Fish Arches
9 6. Route the transducer cable to the sonar unit. Make certain to leave some slack in the cable at the transducer as shown at the bottom of the previous page. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from the engine’s wiring, bilge pumps, vhf radi...
Page 10
10 power connections -permanent mount units only important! Install the transducer before wiring the power cable! The fish id 128 works from a 12 volt dc system only. For the best results, run the power cable directly to the boat’s battery. Keep the power cable away from other boat wiring, especiall...
Page 11
11 fish id 128 portable assembly installing the batteries installing the batteries installing the batteries installing the batteries installing the batteries release the latch on the front of the battery case. Open the compartment and install eight "d" cell batteries into the adapter. For the longes...
Page 12
12 washer washer nut bolt tie nylon cord here screw portable transducer assembly portable transducer assembly portable transducer assembly portable transducer assembly portable transducer assembly assemble the transducer and bracket as shown below. Attach the transducer to the bracket with the suppl...
Page 13
13 clean the chosen area of the hull before attaching the suction cup. Locate the transducer on the hull as shown below. Don't allow the bracket to go below the hull, as water pressure against it can cause the suction cup to come off at speed. Moisten the cup, then press it onto the hull as firmly a...
Page 14
14 keyboard basics the unit sounds a tone when you press any key. This tells you the unit has accepted a command. Pwr/clear use this key to turn the unit on and off. It also clears menu selections and the menus from the screen. Note! To turn the unit off, press and hold the pwr/clear down. A countdo...
Page 15: Operation
15 note: turning the unit off erases all user settings and it returns to the system defaults. For example, if you turn the lights on, then turn the unit off, the next time you turn the unit on, the lights will be off, since the default setting for the lights is off. Menus this sonar unit uses menus ...
Page 16
16 range you can’t adjust the range when the auto- matic mode is on. It is adjustable when the unit is in the manual mode, however. To do so, first put the unit in the manual mode. Now press a menu key until the “range sel” menu appears as shown at right. The current range shows at the bottom of the...
Page 17
17 sensitivity the sensitivity menu lets you control the unit’s ability to pick up echoes. A low sensitivity level excludes much of the bottom information, fish signals, and other detail. High sensitivity settings lets you see features, but it can also clutter the screen with noise and other unwante...
Page 18
18 floats, air bubbles, etc. Individual tree limbs extending outwards from a group of limbs are the hardest objects for the fish id feature to distinguish from fish. You may see fish id symbols on the screen when, in fact, there are no fish. Practice with the unit when the fish id feature is on and ...
Page 19
19 chart speed the rate echoes scroll across the screen is called the chart speed. It’s adjustable by pressing a menu key until the chart speed menu appears. Chart speed is set to maxi- mum when the unit is first turned on. To decrease it, press the down arrow key. Press the up arrow key to increase...
Page 20
20 alarms fish alarm the fish alarm sounds a tone when a fish symbol appears on the screen. To use the fish alarm, press a menu key until the “fish alarm” menu appears on the screen. Now press the up arrow key to turn the alarm on. Repeat the above steps to turn the alarm off. Shallow alarm the shal...
Page 21
21 lights the display is backlighted for night use. To turn the backlights on or off, press a menu key repeatedly until the back light menu appears. Now press the up arrow to turn the lights on or the down arrow to turn them off. The menu will clear automatically after a few seconds. Feet/meter this...
Page 22
22 automatically after a few seconds or press the pwr/clear key to clear the screen. Asp (advanced signal processing) asp is a program embedded in the computer that is specifically designed to eliminate noise. It continually monitors the signals from the receiver, determines which echoes are noise a...
Page 23
23 a a a a a boat's direction of travel boat's direction of travel boat's direction of travel boat's direction of travel boat's direction of travel a a a a a c c c c c b b b b b b b b b b c c c c c fish arches fish arches fish arches fish arches fish arches fish arches are created when the cone of s...
Page 24
24 one of the best ways to get fish arches is to expand or “zoom” a segment of the water. For example, from 45 to 60 feet. The smaller the segment, the better the screen resolution will be. The easiest way to do this is with the zoom feature. This feature expands the echoes, making it easier to see ...
Page 25
25 surface layer absorbs heat from the sun epilimnion thermocline most productive zone for fishing hypolimnion unit won’t turn on: 1. Check the power cable’s connection at the unit. Also check the wiring. 2. Make certain the power cable is wired properly. The red wire connects to the positive batter...
Page 26
26 unit freezes, locks up, or operates erratically: 1. Electrical noise from the boat’s motor, trolling motor, or an accessory may be interfering with the sonar unit. Rerouting the power and transducer cables away from other electrical wiring on the boat may help. Route the sonar unit’s power cable ...
Page 27
27 rejection feature. This can cause the unit to eliminate weaker signals such as fish or even structure from the display. Try using resistor spark plugs or routing the sonar unit’s power and transducer cables away from other electrical wiring on the boat. No fish arches when the fish id feature is ...
Page 28
28 unit’s power cable and transducer cable away from the wiring that is causing the interference. Vhf radio antenna cables radiate noise when transmitting, so be certain to keep the sonar’s wires away from it. You may need to route the sonar unit’s power cable directly to the battery to isolate it f...
Page 29: Eagle Electronics
29 eagle electronics full one-year warranty “we", “our”, or “us” refers to eagle electronics, a division of lei, the manufacturer of this product. “you” or “your” refers to the first person who purchases this product as a consumer item for personal, family, or household use. We warrant this product ...
Page 30
30
Page 31: How to Obtain Service
31 how to obtain service (canadian customers only) we back your investment in quality products with quick, expert service and genuine eagle replacement parts. If you need service or repairs, contact the eagle factory customer service department at the toll-free number listed below. A technician may ...
Page 32: How to Obtain Service
32 eagle electronics may find it necessary to change or end our shipping policies, regulations, and special offers at any time. We reserve the right to do so without notice. Accessory ordering information to order accessories such as power cables or transducers, please contact: 1) your local marine ...