Eagle PA5060E Installation And Operating Instructions Manual
1
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow: Earth (E)
Blue:
Neutral (N)
Brown:
Live (L)
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire which is coloured green and yellow must be connected
to the terminal which is marked by the letter E or by the safety
earth symbol or coloured green and yellow. The wire which is
coloured blue must be connected to the terminal which is
marked with the letter N or coloured black. The wire which is
coloured brown must be connected to the terminal which is
marked with the letter L or coloured red.
If a 13 Amp (B.S. 1363) plug or any other type of plug is used, a
5 Amp fuse must be fitted either in the plug or at the distribution
board.
WARNING: THIS APPLIANCE MUST
BE EARTHED
GENERAL INSTALLATION
DO NOT
use low impedance loudspeakers.
DO NOT
run microphone cables near mains, data,
telephone or 100V line cables.
DO NOT
run 100V line cables near data, telephone or
other low voltage cables.
DO NOT
exceed 90% of the amplifiers output power
when using 100V line (speech only).
DO NOT
exceed 70% of the amplifiers output power
when using 100V line
(high level background music).
DO NOT
use re-entrant horn loudspeakers for
background music unless the loudspeaker has
been specifically designed for this purpose.
AVOID
jointing the microphone cable, when this is
unavoidable make sure a good screened
connector is used, e.g. XLR.
ALWAYS
use a balanced or floating low impedance
microphone terminating into a balanced input
on long microphone cable runs.
ALWAYS
use a mains grade double insulated cable for
the loudspeaker cable runs.
ENSURE
that all loudspeakers are in-phase.
ENSURE
that there are no short circuits on the
loudspeaker line before connecting to the
amplifier.
REMOVE
the top cabinet when fitting the 19” rack ears
supplied (these are fitted using the existing
screw holes and screws from the top cabinet).
PA5000 SERIES TWO ZONE
PUBLIC ADDRESS AMPLIFIERS
INSTALLATION AND OPERATING INSTRUCTIONS
Covers Models:
● PA5120E Mixer Amplifier ● PA5060E Mixer Amplifier ● PAB5120E Booster Amplifier ● PAB5240E Booster Amplifier
● PA5200C Twin Cassette Deck ● PA5200CT Tuner with blank slot for a Cassette Deck or Tuner
Mixer Amplifiers PA5060E and PA5120E
1.
24V DC Connector
14.
Mic 1 Input Socket
2.
Mains Connector
15.
Mic 1 Priority Socket
3.
Loudspeaker Connector
16.
Input Overload Indicator
4.
Booster Out Phono Socket
17.
Mic 1 Level Control
5.
Booster Out DIn Socket
18.
Mic 2 Level Control
6.
Aux 3 Input Socket
19.
Mic 3/Aux 1 Level Control
7.
Mic 5 Input Socket
20.
Mic 4/Aux 2 Level Control
8.
Aux 2 Input Socket
21.
Mic 5/Aux 3 Level Control
9.
Mic 4 Input Socket
22.
Bass Control
10.
Aux 1 Input Socket
23.
Treble Control
11.
Mic 3 Input Socket
24.
Master Level Control
12.
Mic 2 Input Socket
25.
Power On/Off Switch
13.
Mic 2 Priority Socket
26.
Power On Indicator
REAR PANEL
MODEL NO.
PA5120E
RATED OUTPUT 120W RMS
MADE IN TAIWAN
MUSIC/SPEECH
OVER-
LOAD
MIC1
MIC2
MIC3/AUX1
MIC4/AUX2
MIC5/AUX3
BASS
TREBLE
MASTER
16
17
18
19
20
21
22
23
24
25
26
220 - 240V~50/60Hz
24V DC
BOOSTER OUT
AUX 3 MIC5
AUX 2 MIC4
AUX 1 MIC3
SPEECH ONLY
250V 2.5A
1
2
3
4
5
6
7
8
9
10
11
12 13 14 15
FRONT PANEL
GB