EAGTAC GX User Manual
EAGTAC
High Performance Tactical Flashlight
http://www.eagletac.com
GX / MX / SX
User Manual
Models
Quick Start Guide
1) Unscrew the tailcap and remove the
battery isolation disk at the end of the
battery to use. If your flashlight does not
come with battery, insert new batteries
(w/ protrude top) to use. Ensure positive
terminals is facing the LED. Replace
tailcap and tighten snugly.
Adjusting output level
Twist the head to select between four
output levels. You can pre-select the
desired output level
before turning on
the flashlight.
Basic ON and OFF
Turn on the light by press and release
the on/off button switch (<0.4s). To turn
off the light, press and release the
switch again.
For momentary on,
press and hold
the button
switch for
immediate
output.
EAGTAC GX25L2, SX25L2 and MX25L2
models offer maximum output perfor-
mance, versatile user interface, tough
build quality and rich accessories like no
other flashlight offers. This series is
designed for police, professionals, and
hobbyists.
WARNING - Lithium and Li-ion batteries
can explode or cause burns if disas-
sembled, shorted, or exposed to high
temperature. Do not mix with used or
other battery types or install backwards.
IMPORTANT - Only use the integrated built-in
charging socket to charge the original EAGTAC
7.4V battery pack. Charging unbalanced third
party 7.4V 18650 battery pack, two individual
3.7V 18650 cells, or non-rechargeable batteries
(e.g. 3V CR123A) may result in flashlight damage.
LED (Front)
Tail-cap (Back)
1st level
2nd, 3rd,
4th level
Hidden AUX. settings
With the head at tight position (1st
level), loosen to 3rd (or 4th level) and
tighten the head within one second to
enter AUX. setting. Repeat to cycle
through all settings. Turn off the light or
loosen the head to quit.
Strobe (I/II) Hi-Flash S.O.S. (I/II)
Beacon Lo-Flash
All EAGTAC flashlights are designed to
use “button-top” battery (battery with
protruding positive terminal). For
rechargeable li-ion battery, use only
EagleTac li-ion battery, or other
protected li-ion battery with compat-
ible length and diameter. Before using
the battery, check and ensure the
battery outer wrapping (the isolating
plastic film that wraps around the
metal housing of the battery) is com-
plete. Broken battery wrapping may
lead to short circuit and damage to the
flashlight.
Lithium and Li-ion battery can explode
or cause burns if disassembled,
shorted, or exposed to high tempera-
ture. Do not mix new and used batter-
ies. Do not mix batteries with different
brand, capacity, voltage, or install
batteries backwards. When the output
starts to dim (this implies battery is
almost drained), replace the batteries.
Do not drain the batteries completely
especially when you’re using two (or
more) batteries in series.
Battery Safety Precaution
GX25L2 SX25L2
LED
LED Lumen
ANSI Lumen
Runtime
Output
/AUX level
Circuit
Batteries
Voltage
XM-L U2
1060
870
2 - 150 hrs
(R22)
4 / 7
C3500 SEL
2 x18650
2.7V-12V
SST-90 N3
2700
2120
1.3 - 200 hrs
(R44)
4 / 7
C9500 SEL
2 x32650
2.7V-8.4V
3 x XM-L U2
2850
2350
1.3 - 200 hrs
(R44)
4 / 7
C9500 SEL
2 x32650
2.7V-8.4V
XM-L U2
1130
925
2.7 - 200 hrs
(R33)
4 / 7
C4000 SEL
2 x26650
2.7V-8.4V
MX25L2 MX25L2
LED
LED Lumen
ANSI Lumen
Runtime
Output
/AUX level
Circuit
Batteries
Voltage
To switch between tactical and regular
mode, turn on the flashlight at 1st level,
dial to 2nd level and then back to 1st
level for five times within five seconds.
Tactical Mode
100%
10%
Strobe I
Strobe II
Regular Mode
100%
35%
6%
0.1%
Level
1st
2nd
3rd
4th
Battery Isolation Disk