1. DL manuals
  2. Eamlab
  3. Amplifier
  4. Element 302
  5. User Manual

Eamlab Element 302 User Manual

Summary of Element 302

  • Page 1

    1 thank’you of purchasing this eamlab product. Who are dedicated to the policy of creating the highest quality audio components, are proud to introduce. You can be assured that in preparing this component, every attention was paid in great detail by our entire staff to strict quality control . This ...

  • Page 2: Features

    2 features element 302 is a big power amplifier capable up 900 wm rms for channel at 2 ohm impedance. Massive parallel output device combined with biggest and fast power supply guarantee a very high output driven current for difficult system speakers . Innovative system protection via microprocessor...

  • Page 3: Contents

    3 contents 2 …………….Introduction & features 3 …………….Table of contents 4 …………….Safety instructions 5 …………….Unpackaging & preparation 6 …………….Function & protection 8 …………….Front pannel function 9 …………….Connections 10 …………….Troubleshooting guide 11 …………….Datasheet 12 …………….Guarantee policy.

  • Page 4: Warning:

    4 warning: before you start to use read as follows information safety information : 1. For best performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install the unit in a cool, dry, clean place away from windows, heat sources, intense vibration, dust, humi...

  • Page 5

    5 unpacking : carefully remove from the box your amplifier and keep the original carton and packing materials for future trips, expeditions or long-term storage. Introduction : first of all thank you for choosing our a power amplifier. Amplifier built on modern and reliable high construction standar...

  • Page 6

    6 function and protection ready to power on after making all connections correctly we are ready to turn on the amplifier. You just made, the amplifier performs some set in the reset to ensure a safe operation, this is true both in power-on switch-off. As sometimes happens the major problems of high ...

  • Page 7

    7 proceed as follow : turn the amp off and wait about 3 minutes to make sure that the circuit ilp tm resets every parameter. Turn on the amplifier and observe the return to normal operation with led ilp returning fixed. If the problem persists (led always blinking) contact a service center eamlab. N...

  • Page 8: Ilp :

    8 + turn on /off power amp ilp : status led of protection or dc offset output thl : status led of temperature control stand-by led front pannel function.

  • Page 9: Input

    9 input xlr and single ended via rca switch for input select : xlr or rca left and right output to connect speaker : min. 2 ohm front pannel back light : on/off general switch : on/off powercord and service fuse connection 1 : trigger control. For turn on/off amplifier with preamplifier remote contr...

  • Page 10: Problem

    10 no power on the plug on the power cord is not connected or is not fully inserted . The mains fuse is blown securely connect the plug or check the fuse on the rear panel next to the socket no sound or sound very low connecting signal input or output cables incorrect check the rca or xlr cables . S...

  • Page 11: Thd +N

    11 output power in watt rms each channel driven 20 hz to 20khz 300 / 600 / 900 8 / 4 / 2 ohm thd +n 0.03% full power at 8 ohm 1khz signal to noise ratio >105db damping factor 200 at 150 hz 8 ohm input impedance 47 kohm xlr / 25 kohm rca frequency response 5 hz to 80 khz +/- 0.3db 80khz to 150khz +/-...

  • Page 12: How To Expedite Service

    12 how to expedite service return authorization procedure if you believe there is a problem with your component, please contact your dealer, distributor, or the eamlab factory to discuss the problem before you return the component for repair. To expedite service, you may wish to complete and e-mail ...