- DL manuals
- EarthQuake
- Tools
- CS3814
- Operator's Manual
EarthQuake CS3814 Operator's Manual - Important
Page 2
4. Others
Check for fuel leakage and loose fastenings and damage to major
parts, especially handle joints and guide bar mounting. If any defects
are found, make sure to have them repaired before operating again
May require extra grease tip
PERIODICAL SERvICE POINTS
1. Cylinder fins
Dust clogging between the cylinder fins will cause overheating of
the engine. Periodically check and clean the cylinder fins after
removing the air cleaner and the cylinder cover. When installing the
cylinder cover, make sure that switch wires and grommets are
positioned correctly in place.
2. Fuel filter
(a) Using a wire hook, take out the filter from the filler port.
(1) Fuel filter
(b) Disassemble the filter and wash with gasoline,
or replace with a new one if needed.
IMPORTANT
• After removing the filter, use a pinch to hold the end of the
suction pipe.
• When assembling the filter, take care not to
allow filter fibers or dust inside the suction pipe.
Maintenance
Summary of CS3814
Page 1
Operator's manual & parts chain saw cs3814/cs4116 getearthquake.Com omcs3814_cs4116 r082809 © copyright 2009 ardisam, inc. All rights reserved. Printed in china. Warning before using our products, please read this manual carefully to understand the proper use of your unit..
Page 3: Warning
Page safety first instructions contained in warnings within this manual marked with a warning symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them...
Page 4
Page 1. Front hand guard and brake 2. Starter handle 3. Air filter cover 4. Choke knob 5. Throttle trigger lock-out 6. Rear handle 7. Throttle trigger 8. Engine switch 9. Fuel tank 10. Oil tank 11. Front handle 12. Saw chain 13. Guide bar 14. Primer bulb parts location 1 2 3 4 5 6 7 8 9 10 11 13 12 ...
Page 5
Page (1) read operator's instruction book before operating this machine. (2) appropriate ear, eye, and head protection must be worn. (3) use the chain saw with two hands. (4) warning! Danger of kickback. (5) read, understand and follow all warnings. Symbols on the machine.
Page 6
Page for safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. (a). The port to refuel the "mix gasoline" position: near the fuel cap (b). The port to refill the chain oil position: near the oil cap (c)...
Page 7
Page (f). The screw under the "h" stamp is the high-speed adjustment screw. The screw under the "l" stamp is the slow-speed adjustment screw. The screw up the "t" stamp is the idle adjustment screw. Position: upper-left of the rear handle (g). Shows the directions that the chain brake is released (w...
Page 8
Page before operating the product 1. Before using our products, please read this manual carefully to understand the proper use of your unit. 2. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influ...
Page 9
Page 6. Always use caution when handling fuel. Wipe up all spills and then move the chain saw at least ten(10)feet (three(3) m) from the fueling point before starting the engine. 7. Eliminate all sources of sparks or flame (ie. Smoking, open flames, or work that can cause sparks) in the areas where ...
Page 10
Page 10 12. Always carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and the muffler away from your body. 13. Always inspect the chain saw before each use for worn, loose, or changed parts. Never operate a chain saw that is damaged, improperly adjusted, or is not ...
Page 11: Warning
Page 11 19. Guard against kickback. Kickback is the upward motion of the guide bar which occurs when the saw chain at the nose of the guide bar contacts an object. Kickback can lead to dangerous loss of control of the chain saw. Kickback safety precautions for chain saw users warning kickback may oc...
Page 12
Page 12 (2) keep a good grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle, when the engine is running. Use a firm grip with thumbs and fingers encircling the chain saw handles. A firm grip will help you reduce kickback and maintain control of t...
Page 13: Warning
Page 1 3 2 1 4 5 a standard saw unit package contains the items as shown below.： (1) power unit (2) guide bar (3) saw chain (4) plug wrench (5) screwdriver for carburetor adjustment open the box and install the guide bar and the saw chain on the power unit as follows. Warning the saw chain has very ...
Page 14: Note
Page 1 note pay attention to the correct direction of the saw chain. (1)：moving direction 4. Mount the guide bar then fit the saw chain around the bar and sprocket. 5. Fit the chain tensioner nut into the lower hole of the guide bar, then install the chain cover, and fasten the mounting nut to finge...
Page 15: Warning
Page 1 fuel the engines are lubricated by viper engine oil specially formulated for air-cooled 2-cycle gasoline engine use. If oil is not available, use an antioxidant added quality oil expressly labeled for air-cooled 2-cycle chain saw engine use. Recommended mixing ratio gasoline 50 : oil 1 these ...
Page 16: Note
Page 1 4. Pour in the rest of gasoline and agitate again for at least one minute. 5. Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers. Chain oil use special chain saw oil all year round. Recommended for winter or summer use. Note do not use ...
Page 17: Note
Page 1 starting engine 1. Untwist and remove the fuel cap. Rest the cap on a dustless place.. 2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 4. Put the switch to the "i" position. 5. Continuously push the pri...
Page 18: Warning
Page 1 8. When firing occurs, push in the choke knob and pull the starter again to start the engine. 9. Allow the engine to warm up with the throttle lever pulled slightly. Warning before you start the engine, make sure the saw chain is not contacting anything. Checking oil supply after starting the...
Page 19: Important
Page 1 when adjusting, take the following steps: important be sure to adjust the carburetor with the bar chain attached. 1. H and l needles are restricted within the number of turn as shown below. H needle –1/4 l needle –1/4 2. Start engine and allow it to warm up in low speed for a few minutes. 3. ...
Page 20: Warning
Page 20 to release brake, pull up the front handle guard toward the front handle till “click” sound is heard. Warning when the brake operates, release the throttle lever to slow down the engine speed. Continuous operation with the brake engaged will generate heat from the clutch and may cause damage...
Page 21: Warning
Page 21 continuing to use the product in the anti-freeze mode even when temperatures have risen and returned to normal, may result in the engine failing to start properly or in the engine failing to operate at its normal speed, and for this reason you should always be sure to return the unit to the ...
Page 22: Warning
Page 22 clutch drum before use. It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to maintain the kickback safety level of this saw. Removal of the safety devices, inadequate maintenance, or incorrect replacement of th...
Page 23: Warning
Page 2 logging and limbing warning 1. Always ensure your foothold as well as stability of the tree. 2. Be alert to the rolling over of a cut log. 3. Read the instructions in “for safe operation” to avoid kickback of the saw. Before starting work, check the direction of bending force inside the log t...
Page 24: Warning
Page 2 pruning cut up from the bottom, finish down from the top. Warning 1. Do not use an unstable foothold or a stepladder. 2. Do not overreach. 3. Do not cut above shoulder height. 4. Always use both hands to grip the saw. Sawing.
Page 25: Warning
Page 2 warning before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. Maintenance after each use 1. Air filter dust on the cleaner surface can be removed by tapping a corner of the cleaner against a...
Page 26: Important
Page 2 4. Others check for fuel leakage and loose fastenings and damage to major parts, especially handle joints and guide bar mounting. If any defects are found, make sure to have them repaired before operating again may require extra grease tip periodical service points 1. Cylinder fins dust clogg...
Page 27
Page 2 3. Spark plug clean the electrodes with a wire brush and reset the gap to 0.635 mm as necessary. (.025 in.) spark plug type：champion cj7y 4. Sprocket check for cracks and for excessive wear interfering with the chain drive. If the wearing is found obviously, replace it with a new one. Never f...
Page 28: Warning
Page 2 saw chain warning it is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • sawdust becomes powder-like. • you need extra force to saw in. • the cut way does not go straight. • vibration increases. • fuel consumption increas...
Page 29: Warning
Page 2 maintenance of chain / bar after every cutter has been set, check the depth gauge and file it to the proper level as illustrated. Warning be sure to round off the front edge to reduce the chance of kickback or tie-strap breakage. (1) appropriate gauge checker (2) make the shoulder round (3) d...
Page 30: Warning
Page 0 warning this saw is equipped with the following low kickback bar/chain combination: guide bar： cs4116……………………….Oregon160sdea041 cs3814……………………….Oregon140sdea041 saw chain： cs3814………………………………………oregon s52 cs4116………………………………………oregon s56 for replacement use only above bars and chains maintenanc...
Page 31
Page 1 1. Empty the fuel tank and run the engine out of fuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of the reach of children. Storage.
Page 32
Page troubleshooting guide problem cause remedy starting failure check fuel for water or substandard mixture replace with proper fuel remove and dry the spark plug then pull the starter again with no choke replace with a new plug lack of power / poor ac- celeration / rough idling check for water or ...
Page 33
Page specifications power unit displacement cs3814 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37.2cc cs4116 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40.1cc maximum engine power . . . . . . . . . . . . . . . . . . . ....
Page 34
Page 1-year limited warranty terms and conditions ardisam, inc., a manufacturing company, warrants this earthquake® chain saw to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one year warranty of this product, ardisam will furnish ...
Page 35
Page 0 earthquake, division of ardisam, inc. • 1160 eighth avenue; p.O. Box 666 cumberland, wisconsin 54829 800-345-6007 · fax (715) 822-4180 • e-mail: info@ardisam.Com getearthquake.Com visit www.Ardisam.Com and discover more innovations that will benefit you throughout the year..