1. DL manuals
  2. East
  3. UPS
  4. EA300PRO series
  5. User Manual

East EA300PRO series User Manual

Manual is about: Line Interactive Sinewave UPS 800/1.1K/1.5K/2K/2.5K/3K VA

Summary of EA300PRO series

  • Page 1

    Line interactive sinewave ups 800/1.1k/1.5k/2k/2.5k/3k va uninterruptible power supply system user manual.

  • Page 2

    1 table of contents 1. Important safety warning……………………………………………… 2 1-1. Transportation 2 1-2. Preparation 2 1-3. Installation 2 1-4. Operation 2 1-5. Maintenance, service and faults 3 2. Installation and setup…………………………………………………… 4 2-1. Rear panel view 4 2-2. Install the ups 5 2-3. Setup the ups 5 ...

  • Page 3

    2 1. Important safety warning please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating i...

  • Page 4

    3 1-5. Maintenance, service and faults  the ups system operates with hazardous voltages. Repairs may be carried out only by qualified maintenance personnel.  caution - risk of electric shock. Even after the unit is disconnected from the mains (building wiring outlet), components inside the ups sys...

  • Page 5

    4 2. Installation and setup note: before installation, please inspect the unit. Be sure that nothing inside the package is damaged. Please keep the original package in a safe place for future use. 2-1. Rear panel view 800/1.1k/1.5k/2k iec type 2.5k/3k iec type 800/1.1k/1.5k/2k schuko type 2.5k/3k sc...

  • Page 6

    5 2-2. Install the ups for safety consideration, the ups is shipped out from factory without connecting battery wires. Before install the ups, please follow below steps to re-connect battery wires first. Step 1 step 2 step 3 remove front panel. Connect the ac input and re-connect battery wires. Put ...

  • Page 7

    6 step 3: communication connection communication ports: usb port rs-232 port intelligent slot to allow for unattended ups shutdown/start-up and status monitoring, connect the communication cable one end to the usb/rs-232 port and the other to the communication port of your pc. With the monitoring so...

  • Page 8

    7 step 7: turn on the ups press the on/mute button on the front panel for two seconds to power on the ups. Note: the battery charges fully during the first five hours of normal operation. Do not expect full battery run capability during this initial charge period. Step 8: install software for optima...

  • Page 9

    8 2-5 battery kit assembly (option) notice: please assemble battery kit first before installing it inside of ups. Please select correct battery kit procedure below to assemble it. 2-battery kit step 1: remove adhesive tapes. Step 2: connect all battery terminals by following below chart. Step 3: put...

  • Page 10

    9 6-battery kit step 1: remove adhesive tapes. Step 2: connect all battery terminals by following below chart. Step 3: put assembled battery packs on one side of plastic shells. Step 4: cover the other side of plastic shell as below chart. Then, battery kit is assembly well. Tapes tapes.

  • Page 11

    10 3. Operations 3-1. Button operation button function on/mute button  turn on the ups: press and hold on/mute button for at least 2 seconds to turn on the ups.  mute the alarm: after the ups is turned on in battery mode, press and hold this button for at least 5 seconds to disable or enable the a...

  • Page 12

    11 display function backup time information indicates the backup time in pie chart. Indicates the backup time in numbers. H: hours, m: minute warning & fault information indicates that the warning and fault occurs. Indicates the warning and fault codes, and the codes are listed in details in 3-5 sec...

  • Page 13

    12 3-4. Lcd display wordings index abbreviation display content meaning ena enable dis disable esc escape ep epo fa fan tp temperature ch charger rac rack display toe tower display sf site fault 3-5. Ups setting there are two parameters to set up the ups. Parameter 1: it’s for program alternatives. ...

  • Page 14

    13  03: programmable outlets setting interface setting setting the backup time limits in minutes from 0-999 for programmable outlets which connect to non-critical devices on battery mode.  04: lcd display direction setting interface setting rac: the lcd display is horizontal. Toe: the lcd display ...

  • Page 15

    14 step 4: press the “up“ button (on/mute) again to switch to "03" of program list. Then press “enter“ button for setting programmable outlet time. Push “up” button to change the value of backup time according your demand. Then press “enter” to confirm the setting. Step 5: press “up“ button (on/mute...

  • Page 16

    15 operating mode description lcd display standby mode ups is powered off and no output supply power, but still can charge batteries. 3-7. Faults reference code fault event fault code icon fault event fault code icon bus start fail 01 x inverter output short 14 bus over 02 x battery voltage too high...

  • Page 17

    16 4. Troubleshooting if the ups system does not operate correctly, please solve the problem by using the table below. Symptom possible cause remedy no indication and alarm even though the mains is normal. The ac input power is not connected well. Check if input power cord firmly connected to the ma...

  • Page 18

    17 symptom possible cause remedy fault code is shown as 1, 2, 3, 4, 11, 12, 13 and 41 on lcd display and alarm is continuously sounding. A ups internal fault has occurred. Contact your dealer battery backup time is shorter than nominal value batteries are not fully charged charge the batteries for a...

  • Page 19

    18 5. Storage and maintenance 5-1. Operation the ups system contains no user-serviceable parts. If the battery service life (3~5 years at 25°c ambient temperature) has been exceeded, the batteries must be replaced. In this case, please contact your dealer. Storage before storing, charge the ups 5 ho...

  • Page 20

    19 model 800 1.1k(l) 1.5k 2k(l) 2.5k 3k(l) capacity 800 va / 640 w 1100 va / 880 w 1500 va / 1200 w 2000 va / 1600 w 2500 va / 2000 w 3000 va / 2400 w input acceptable voltage range 81-145 vac or 162-290 vac frequency range 60/50 hz (auto sensing) output voltage regulation (ac mode) 110/120 vac or 2...