EasternCCTV IP-5VP5M32VF Quick Start Manual
Package
Overview
Installation
1
2
3
4
2
1
3
Thank you for purchasing our product. There may be several
technically incorrect places or printing errors in this manual.
The updates will be added into the new version of this manual.
We will readily improve or update the products or procedures
described in the manual. The content is subject to change
without notice.
Warning
and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Keep away from liquid while in use.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the product
is mounted on wall or ceiling, the device shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -20˚C~50˚C), dusty or damp locations, and do
not expose it to high electromagnetism radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
■ A few parts of the device shall be replaced regularly according
to their average enduring time.
Quick
Start Guide
Network
Camera
Camera
Quick
start
guide
CD
Water
-
proof
cap
Plastic
plug
×4
Drill
template
Sponge
Screwdriver
4 tapping screws PA 4×25
enough to withstand 3 times the weight of the camera. Please install
and use the camera in the dry environment. You'd better install back
the lower dome less than 4 hours after removing it. The mounting
steps are as follows:
① Loosen the screws to open the lower dome and then loosen the
lock screw to remove the mounting base.
Before start, please make sure that the wall or ceiling is strong
② Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the
cables through the mounting base) according to the drill template.
Lock
Screw
Lower
Dome
∅6
∅148
∅22
88 mm
89mm
CVBS&DC
IN cables
N
et
w
or
k C
ab
le
8
9
10
RES
ET
TF
LINK
DC IN
CVBS
1
2
3
4
5
6
7
ALM-COM
ALM-NO
ALM-IN
ALM-GND
RS485T+
RS485T-
Microphone Cable
Headphone Cable
TF
Card Slot
Reset
Hole
CVBS/DC IN port for testing
Alarm Input/Output
RS485 Cable
Video
Output
Network
Cable
Power
Cable
1
2
3
5
7
9
4
6
8
10
* 1 It is recommended to install the water-proof cap for network cable connection.
* 2 If the
switch
is used to connect the camera, DC12V power supply
is not required.
PoE network
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then
crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut
and the main cover.
●
Alarm Input: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port of the camera.
Alarm Output: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
NO and COM separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
●
Connecting Network Cable
Alarm Connection