EasyCool AIR01 User Manual - page 5
5
FEATURES AND PARTS LIST
Features:
·
No installation is required.
·
Easily moved . The handle makes moving more convenient.
·
Streamline colorful screen display .
·
LED colorful screen display.
·
Water-cooled mode is most energy saving and environment protect.
·
Low noise and strong wind .
·
Unique economic function.
·
Auto swing makes wind blow from left to right automatically.
·
Three-minute restart delay to protect compressor.
Parts list:
1. control panel
2. horizontal louver
3. vertical louver
4. air inlet grille
5. castor
6. exhaust duct
7. handle
8. air outlet grille
9. power cord and plug
10. water injection port
11. power and hook
12. air filter
PANEL CONTROL
CAUTIONS:
If the unit is turned off in cool /dry/ heat mode and restarted
immediately , then it will wait at least 3minutes before running again.
1. Buttons
Timer: press this button to set the timer
Swing: press this button to make the vertical louver swing automatically.
Press once again, the swing will stop.
Speed: press this button for 5 seconds to select high, middle or low fan
Speed.
Up/down: press up or down button to set temperature or adjust the time in
Timer mode. Press both buttons to vary from Celsius to Fahrenheit.
Mode: press this button to select cool, heat, dry or fan mode (heat mode
only in YPC-H models).
Econ: press this button to a set energy saving mode (only in heat and cool
mode). This set temperature is 27℃ in cool mode and 23℃ in heat
mode . The fan speed is low. These data can’t be changed. The LED
display will flash or accordingly. Press again to cancel it when
or is flashing.
Power: press this button to turn on/off the unit.
2. LED display
Timer indicator
Dry, cool, fan and heat mode indicator (no in YPC-C models)
High, middle and low fan speed indicator
Water Full indicator
Water Injection indicator
IR receiver window
Indicate the time and temperature. Display EX (X=2,3) when
there is something wrong (refer to Self diagnosis function).
Display E4 when coil is defrosted.
Celsius degree and Fahrenheit degree indicator.
10
WATER DRAINGE METHODS
This product has a self-evaporative system. The condensing water
will recycle to cool the condenser. This water-cooled mode can not
only improve cooling efficiency and decrease noise, but also save
energy for you.
* When in cooling mode, the water from the evaporator will flow into a inside
pan. When the water reaches the low level, the water pump will work until
the water is under the low level. When the water reaches the high level, the
compressor will stop working, and the water pump, lower fan motor and
upper fan motor will work on all the time.
* When in heating mode, the water pump won't work.
* When the water is full, the water full indicator will light and the compressor
will stop working. The buzzer will buzz 10 times every 5 minutes until the
water is below the high level or drained by hand. When the alarm stops and
after three-minutes restart delay, the unit will
work normally.
* You can drain the water out with a drain pipe. It
is included in the accessory. But first you
should put some vessel like pan under the
hose, then take out the plug on the drain mouth,
thus the water will flow into the vessel and
won't make the floor wet. (Fig.13) If the
drainpipe is shorter than you need, you can
purchase a pipe (9mmI.D.). Then connect it to
the drainpipe with the drainpipe kit we supply.
* Move the unit gently when the water is high. If
not , the water may spill from the inside of the unit.
* When the water in the cave is not enough for pumping, the pump will stop
working. At the same time, the Water Injection indicator on the control panel
will illuminate ( ), you had better inject some water into the water draw
carefully. In order to avoid the water flooding from the under pan, you should
inject water not more than 1800ml (three cups). This operation helps save
20%-30% energy for you.