Summary of DJ 1T
Page 1
Dj 1t/dj 2t user manual dj 1t dj 2t.
Page 2
Contents 1.Parts and functions............................................................................................. 1 2.Terminal descriptions .......................................................................................... 1 3.Specifications ...........................................
Page 3
-1- o n 1 2 17 6 m m o n 1 2 1.Parts and functions camera lens night view led speaker nameplate microphone rainy cover 90 mm 23 mm note: dj 2t has two call buttons. 2.Terminal descriptions 1 2 3 lock control jumper doorstation code dip mic adjustment spk adjustment main connect port.
Page 4
-2- • lock control jumper: to select the lock type: see 5.2.1 , 5.2.2 • doorstation code dip: total 4 doorstations can be supported,see 6.1 • main connect port: to connect the bus line and the electronic locks. • bus: connect to the bus line, no polarity. • pl: external lock power input, connect to ...
Page 5
-3- o n 1 2 4.2 mounting with rainy cover 1 160-165cm 2 3 1 2 4 4.3 placing name label move the plastic cover away to open the transparent name label cover, insert a name paper, then put the plastic cover back to the panel. Name label.
Page 6
-4- o n 1 2 4.4 adjusting camera angle use a screwdriver to loosen the screw and then adjust the angle of the camera ,then fix the screw. 5.System wiring and connections 5.1 basic connection l1 l2 pl s1+ s2+ s- sp 18 24vdc monitor - +.
Page 7
-5- on 1 2 on 1 2 5.2 electric lock connection 5.2.1 door lock controlled with internal power note: 1. Electronic lock of power-on-to-unlock type should be used. 2. The door lock is limited to 12v, and holding current must be less than 250ma. 3. The door lock control is not timed from exit button(eb...
Page 8
-6- unlock time 1 unlock mode 0 exit hardware ver 0302 softwarever 0168 voltage 22.4v manufacture 00.0t restore to default exit on 12 on 12 connect one lock connect two locks 1 2 3 1 2 3 take off the jumper take off the jumper bus pl s1+ s2+ s- bus pl s1+ s2+ s- + + lock #2 - - - + - + power supply ...
Page 9
-7- on 12 on 12 on 12 on 12 5.3 multi doorstations connection monitors bus vd 04 a b c d sp18 24vdc 85~260vac 4# camera id=11 3# camera id=01 2# camera id=10 1# camera id=00 on on on on 1 2 1 2 1 2 1 2 l1 l2 pl s1+ s2+ s- l1 l2 pl s1+ s2+ s- l1 l2 pl s1+ s2+ s- l1 l2 pl s1+ s2+ s-.
Page 10
-8- 5.4 multi monitors connection 5.4.1 basic in-out wiring mode on 1 2 3 4 5 6 code=31, dip-6=on monitor on 1 2 3 4 5 6 code=14, dip-6=off monitor on 1 2 3 4 5 6 code=32, dip-6=off monitor sp18 24vdc 85~260ac id=00 on 1 2.
Page 11
-9- vd 04 vd 04 ou t in a b c d ou t in a b c d 5.4.2 with vd 04 wiring mode on 1 2 3 4 5 6 code=15, dip-6=on monitor on 1 2 3 4 5 6 code=14, dip-6=on monitor hi on 1 2 3 4 5 6 code=13, dip-6=on monitor on 1 2 3 4 5 6 code=12, dip-6=on monitor on 1 2 3 4 5 6 code=3, dip-6=on monitor on 1 2 3 4 5 6 c...
Page 12
-10- 6.Setup on(1) = off(0) = 6.1 dip switches settings of doorstation total 2 bits on the dip switches can be configured.The switches can be modified etther before or after installation. Bit state descriptions on 1 2 default setting, id = 0(00), set to the first door station. On 1 2 id = 1(10), set...
Page 13
-11- bit-1 to bit-5 are used to user code setting. The value is from 1 to 32, which have 32 different codes . Note:monitors response button a must set the user code to 32, and button b set the user code to 16. B a a.
Page 14
-12- 6.3 notices name discription useage 24vdc power supply,85~260vac input,24vdc/>3a output, connect with multi doorstations or multi monitors(up to 2 or above) ps 1a power supply,85~260vac input,24vdc/1a output,for basic kit only,4 din modules c onnect with one doorstation and on e monitor(vm 35 c...
Page 15
-13- cable usage a b c twisted cable 2x0.75 mm 2 60 60 30 twisted cable 2x1 mm 2 80 80 40 7.Cables requirements the maximum distance of the wiring is limited in the easydoor system. Using different cables may also effect the maximum distance the system can reach. The farest monitor monitor with two ...
Page 16
-14-.