English copyright © 2013 eaton all rights reserved. Service and support: call your local service representative 619-00470-01-i (en) 5sc 500i 5sc 750i 5sc 1000i 5sc 1500i installation and user manual.
Page 2 619-00470-01-i (en) certification standards special symbols the following are examples of symbols used on the ups or accessories to alert you to important information: risk of electric shock - observe the warning associated with the risk of electric shock symbol. Important instructions that m...
Page 3 619-00470-01-i (en) english contents 1. Introduction ....................................................................................... 4 1.1 environmental protection ...................................................................................................4 2. Presentation .......
Page 4 619-00470-01-i (en) 1. Introduction thank you for selecting an eaton product to protect your electrical equipment. The 5sc range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your ups (uninterrupt...
Page 5 619-00470-01-i (en) english 2. Presentation 2.1 standard installation d h w description weights (kg/lb) dimensions (mm/inch) d x w x h 5sc 500i 6.60 / 14.60 240 x 150 x 210 / 9.4 x 5.9 x 8.3 5sc 750i 10.40 / 22.90 340 x 150 x 210 / 13.4 x 5.9 x 8.3 5sc 1000i 11.10 / 24.50 340 x 150 x 210 / 13...
Page 6 619-00470-01-i (en) 2. Presentation 2.3 control panel the ups has a three-button lcd. It provides useful information about the ups itself, load status, events, measurements and settings. Avr % min hz kva kw 6 7 8 6 on/off button 7 scroll down 8 mute alarm 2.4 lcd description 16 15 14 17 11 10...
Page 7 619-00470-01-i (en) english 3. Installation 3.1 unpacking and contents check 1 2 3 4 5 6 (1) 5sc ups (2) quick start and safety instructions (3) user manual and ipss (intelligent power software suite) cdrom (4) 2 connection cables for the protected equipment (5) rs232 communication cable (6) ...
Page 8 619-00470-01-i (en) 3. Installation 3.2 communication ports connection of rs232 or usb communication port the rs232 and usb communication ports cannot operate simultaneously. 2 1 5 6 1. Connect the rs232 (5) or usb (6) communication cable to the serial or usb port on the computer equipment. 2...
Page 9 619-00470-01-i (en) english 4. Operation 4.1 start-up and normal operation to start the ups: 1. Verify that the ups power cord is plugged in. 2. Press the button on the ups front panel for at least 2 seconds. 3. Check the ups front panel display for active alarms. If the indicator is on, do n...
Page 10 619-00470-01-i (en) 5. Maintenance 5.1 troubleshooting operation status possible cause action overload power requirement exceeds the ups capacity (greater than 105 % of nominal). Remove some of the equipment from the ups.The ups continues to operate, but may shutdown if the load increases.Th...
Page 11 619-00470-01-i (en) english 5. Maintenance 5.2 battery-module replacement safety recommendations the battery can cause electrocution and high short-circuit currents. The following safety precautions are required before servicing the battery components: • remove watches, rings, bracelets and ...
Page 12 619-00470-01-i (en) 6. Appendices 6.1 technical specifications 5sc 500i 5sc 750i 5sc 1000i 5sc 1500i output power @ 230 v 500 va 350 w 750 va 525 w 1000 va 700 w 1500 va 1050 w ac input power •rated input voltage single phase 220-240 v •input voltage range 184 to 276 v • input frequency rang...
