Eaton EDR 3000 Installation, Operation And Maintenance Manual

Page 1

Operation & maintenance manual general order mrm0007157 volume 3 of 6 equipment: medium voltage switchgear assembly pentagon - mcm7571 date: 2016-04-08 wesco midlothian va 7582 po# 7582-785492 york river electric ©2015 eaton corporation, all rights reserved.

Page 4

Edr-3000 im02602003e device planning parameters of the device parameter description options default menu path hardware variant 1 optional hardware extension »a« 4 digital inputs

Page 7

Medium voltage switchgear assembly.

Page 11

Component data.

Page 14

Edr-3000 im02602003e edr-3000 functional overview www.Eaton.Com 2 50p standard 3 1 50x 51x cts 79 74 tc option fundamental and rms, max/min/avg currents thd current current phasors sequence currents metering sotf clpu trend recorder event recorder fault recorder waveform recorder zone interlocking i...

Page 16

Edr-3000 im02602003e powerport-e keyboard commands........................................................................................................................... 170 measuring values.............................................................................................................

Page 18

Edr-3000 im02602003e breaker wear............................................................................................................................................................ 384 control - example: switching of a breaker....................................................................

Page 20

Edr-3000 im02602003e comments on the manual this manual gives a general explanation of the tasks of device planning, parameter setting, installation, commissioning, operation, and maintenance of the eaton devices. The manual serves as reference document for: engineers in the protection field; commis...

Page 22

Edr-3000 im02602003e typical applications for this product family/device line are for example: feeder protection; mains protection; transformer protection and machine protection. This device is not designed for any usage beyond these applications. This applies also to the use as a partly completed m...

Page 24

Edr-3000 im02602003e electrostatic discharge awareness all electronic equipment is sensitive to electrostatic discharge, some components more than others. To protect these components from electrostatic damage, the user must take special precautions to minimize or eliminate electrostatic discharges. ...

Page 26

Edr-3000 im02602003e symbols www.Eaton.Com 14 in ac tiv e ac tiv e ig .D ir n po ss - >n on di r t rip 1 2 s et tin g v al ue : am e> . I d ev ic e p la nn in g: am e> s ig na l: ig m ea su re d v al ue s: am e> .*i nt a lm l 1 in te rn al m es sa ge f un ct io na l d es cr ip tio n: if th e se tti ...

Page 28

Edr-3000 im02602003e www.Eaton.Com 16 2 2 in p u t s ig n al o u tp u t s ig n al 2 n am e. A ct iv e 3 n am e. B lo t rip c m d 4 n am e. A ct iv e 5 ih 2. B lo p ha se a 6 ih 2. B lo p ha se b 7 ih 2. B lo p ha se c 8 ih 2. B lo ig 9 n am e. F au lt in p ro je ct ed d ire ct io n 10 n am e. F au l...

Page 30

Edr-3000 im02602003e www.Eaton.Com 18 41 bk r.P ro t c lo s e 42 bk r.C lo se c m d b kr .P ro t c lo s e b kr .C lo s e c m d 3 9 p le as e r ef er to d ia gr am : q -> &v d ec ou pl in g di st rib ut ed g en er at or q -> &v d ec ou pl in g di st rib ut ed g en er at or 4 0 p le as e r ef er to d ...

Page 32

Edr-3000 im02602003e general conventions www.Eaton.Com 20 » parameters are indicated by right and left double arrow heads and written in italic .« »signals are indicated by right and left double arrow heads and small caps .« [paths are indicated by brackets.] software and device names are written in...

Page 34

Edr-3000 im02602003e device edr-3000 device planning pla nning of a device means to reduce the functional range to a degree that suits the protection task to be fulfilled ( i.E.: the device shows only those functions needed or desired). If the user, for example, deactivates the voltage protection fu...

Page 37

Edr-3000 im02602003e the housing must be carefully grounded. Connect a ground cable (4 to 6 mm 2 [awg 12-10] / 1.7 nm [15 in-lb]) to the housing, using the screw that is marked with the ground symbol (at the rear side of the device). The power supply card needs a separate ground connection (2.5 mm 2...

Page 39

Edr-3000 im02602003e overview of slots - assembly groups in line with the customers' requirement, the devices are combined in a modular way (in compliance with the order code). In each of the slots, an assembly/group may be integrated. In the following diagram, the terminal assignment of the individ...

Page 41

Edr-3000 im02602003e slot x1: power supply card with digital inputs rear side of the device (slots) the type of power supply card and the number of digital inputs on it used in this slot is dependent on the ordered device type. The different variants have a different scope of functions. Available as...

Page 43

Edr-3000 im02602003e terminal marking pin assignment www.Eaton.Com 31 v+ v- di1 di2 di3 di4 com1 di-4p x com2 n.C. 1 3 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 power supply n.C. N.C. N.C. N.C. N.C. N.C. Do not use do not use 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 v+ power supply n.C. Com1 di1 ...

Page 45

Edr-3000 im02602003e terminal marking pin assignment www.Eaton.Com 33 v+ v- com1 di1 com2 di2 di3 di4 di5 di6 di7 di8 com3 do not use di-8p x com3 n.C. Do not use 1 3 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 power supply 1 2 3 4 5 6 7 8 9 10 11 12 com1 13 14 15 16 17 18 v+ power supply di1 com2 di2 ...

Page 47

Edr-3000 im02602003e ro-3 x - relay outputs and supervision contact the relay outputs are potential-free contacts. In the assignment/relay outputs section, the assignment of the relay outputs is specified. The changeable signals are listed in the assignment list section . Make sure that the tighteni...

Page 49

Edr-3000 im02602003e ro-5 x - relay outputs and system contact the relay outputs are potential-free contacts. In the assignment/relay outputs section, the assignment of the relay outputs is specified. The changeable signals are listed in the assignment list section . Make sure that the tightening to...

Page 51

Edr-3000 im02602003e ro-3zi x - relay outputs, irig-b00x, zone interlock and sc the relay outputs are potential-free contacts. In the assignment/relay outputs section, the assignment of the relay outputs is specified. The changeable signals are listed in the assignment list section . Make sure that ...

Page 53

Edr-3000 im02602003e slot x3: current transformer measuring inputs rear side of the device (slots) available assembly groups in this slot: (ti-4 x3): standard ground current measuring card. (tis-4 x3): sensitive ground current measuring card. The technical data of the sensitive ground measuring inpu...

Page 55

Edr-3000 im02602003e terminal markings pin assignment www.Eaton.Com 43 ia-1a ia-n ia-5a ib-1a ib-n ic-1a ic-n ic-5a ix-1a ix-n ix-5a ib-5a 1 2 3 4 5 6 7 8 10 11 9 12 1 2 3 4 5 6 7 8 9 10 11 12 ia 1a 5a n ib 1a 5a n ic 1a 5a n ix 1a 5a n x?..

Page 57

Edr-3000 im02602003e terminal markings pin assignment www.Eaton.Com 45 ia-1a ia-n ia-5a ib-1a ib-n ic-1a ic-n ic-5a ix-1a ix-n ix-5a ib-5a 1 2 3 4 5 6 7 8 10 11 9 12 1 2 3 4 5 6 7 8 9 10 11 12 ia 1a 5a n ib 1a 5a n ic 1a 5a n ix 1a 5a n x?..

Page 59

Edr-3000 im02602003e 3-phase, 3-wire ig calculated www.Eaton.Com 47 a b c ia ib ic 1 x?. 2 3 4 5 6 7 8 9 10 11 12 three-phase current measurement; inom secondary = 5 a. Ia 1a 5a n ib 1a 5a n ic 1a 5a n ix 1a 5a n ib' ic' ia' ir calc = ia + ib + ic = ig.

Page 61

Edr-3000 im02602003e 4-wire system, 4 th ct on neutral www.Eaton.Com 49 a b c ia ib ic 1 x?. 2 3 4 5 6 7 8 9 10 11 12 4-wire system, 4th ct on neutral; in secondary = 5 a. Ia 1a 5a n ib 1a 5a n ic 1a 5a n ix 1a 5a n ib' ic' ia' n in in' ix meas=in ir calc = ig = ia + ib + ic + in ir calc´.

Page 63

Edr-3000 im02602003e slot x100: ethernet interface rear side of the device (slots) an ethernet interface may be available depending on the device type ordered. The available combinations can be gathered from the ordering code. Www.Eaton.Com 51 x1 x2 x3 slot1 slot2 slot3 x100 x 10 1 x103.

Page 65

Edr-3000 im02602003e slot x101: irig-b00x rear side of the device (slots) if the device is equipped with an irig-b00x interface is dependent on the ordered device type. The available combinations can be gathered from the ordering code. Www.Eaton.Com 53 x1 x2 x3 slot1 slot2 slot3 x100 x 10 1 x103.

Page 67

Edr-3000 im02602003e slot x103: data communication rear side of the device (slots) the data communication interface in the x103 slot is dependent on the ordered device type. The scope of functions is dependent on the type of data communication interface. Available assembly groups in this slot: rs485...

Page 69

Edr-3000 im02602003e wiring example: device in the middle of the bus wiring example: device at the end of the bus (using the integrated terminal resistor) www.Eaton.Com 57 6 4 5 3 2 1 +5v gnd r1 = 560 Ω r2 = 120 Ω protective relay b(+) b(+)* a(-) a(-)* r1 r2 r1 h f s hi el d 6 4 5 3 2 1 +5v gnd r1 =...

Page 71

Edr-3000 im02602003e www.Eaton.Com 59 1 3 2 4 5 6 t r -p 1 3 2 4 5 6 t r -p 1 3 2 4 5 6 t r -p 1 3 2 4 5 6 t r -p shield at bus master side connected to earth termination resistors used shield at bus device side connected to earth termination resistors used shield at bus master side connected to ear...

Page 73

Edr-3000 im02602003e control wiring diagram below is the recommended control wiring schematic for the edr-3000. Www.Eaton.Com 61.

Page 75

Edr-3000 im02602003e input, output and led settings digital input configuration the state of the digital inputs can be checked within menu: [operations/status display/name of the assembly group (e.G. Di-8x)] the digital inputs can be configured within menu: [device para/digital inputs/name of the as...

Page 77

Edr-3000 im02602003e parameter description setting range default menu path debouncing time 2 a change of the state of a digital input will only be recognized after the debouncing time has expired (become effective). Thus, transient signals will not be misinterpreted. No debouncing time, 20 ms, 50 ms...

Page 79

Edr-3000 im02602003e digital inputs output signals on di-8p x signal description di 1 signal: digital input di 2 signal: digital input di 3 signal: digital input di 4 signal: digital input di 5 signal: digital input di 6 signal: digital input di 7 signal: digital input di 8 signal: digital input www...

Page 81

Edr-3000 im02602003e parameter description setting range default menu path debouncing time 3 a change of the state of a digital input will only be recognized after the debouncing time has expired (become effective). Thus, transient signals will not be misinterpreted. No debouncing time, 20 ms, 50 ms...

Page 83

Edr-3000 im02602003e wired inputs (aliases) available elements: wired inputs the module wiredinputs allows to alias digital inputs. By means of the menu [device para/wiredinputs] the user can assign specific functions on digital inputs. Alias example: the 52a contact will be assigned/connected to di...

Page 85

Edr-3000 im02602003e parameter description setting range default menu path 52b t tie breaker open 1..N, dig inputs -.- [device para /wired inputs] toca t tie breaker connected 1..N, dig inputs -.- [device para /wired inputs] 43/10 t tie breaker selected to trip 1..N, dig inputs -.- [device para /wir...

Page 87

Edr-3000 im02602003e relay output configuration the state of the relay outputs can be checked within menu: [operations/status display/name of the assembly group (e.G. Ro-xx)] the relay outputs can be configured within menu: [device para/relay outputs/name of the assembly group (e.G. Ro-xx)] set the ...

Page 89

Edr-3000 im02602003e if the relay output contacts are configured as » latched= active«, they will k eep their position even if there is a power outage within the power supply of the protective device. If the relay output contacts are configured as »latched=active«, they will also retain their positi...

Page 91

Edr-3000 im02602003e device parameters of ro-3 x parameter description setting range default menu path operating mode operating mode norm de-energ, norm energ norm de-energ [device para /relay outputs /ro-3 x2 /ro 1] t-off delay switch off delay 0.00 - 300.00s 0.2s [device para /relay outputs /ro-3 ...

Page 93

Edr-3000 im02602003e parameter description setting range default menu path inverting 7 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-3 x2 /ro 1] operating mode operating mode norm de-energ, norm energ norm de-energ [device para /relay output...

Page 95

Edr-3000 im02602003e parameter description setting range default menu path assignment 7 assignment 1..N, assignment list -.- [device para /relay outputs /ro-3 x2 /ro 2] inverting 7 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-3 x2 /ro 2] op...

Page 97

Edr-3000 im02602003e parameter description setting range default menu path inverting 6 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-3 x2 /ro 3] assignment 7 assignment 1..N, assignment list -.- [device para /relay outputs /ro-3 x2 /ro 3] in...

Page 99

Edr-3000 im02602003e input states of ro-3 x name description assignment via ro1.1 module input state: assignment [device para /relay outputs /ro-3 x2 /ro 1] ro1.2 module input state: assignment [device para /relay outputs /ro-3 x2 /ro 1] ro1.3 module input state: assignment [device para /relay outpu...

Page 101

Edr-3000 im02602003e name description assignment via ro3.2 module input state: assignment [device para /relay outputs /ro-3 x2 /ro 3] ro3.3 module input state: assignment [device para /relay outputs /ro-3 x2 /ro 3] ro3.4 module input state: assignment [device para /relay outputs /ro-3 x2 /ro 3] ro3....

Page 103

Edr-3000 im02602003e ro-5 x settings ro-5 x2 direct commands of ro-5 x parameter description setting range default menu path disarmed this is the second step, after the "disarmed ctrl" has been activated, that is required to disarm the relay outputs. This will disarm those relay outputs that are cur...

Page 105

Edr-3000 im02602003e device parameters of ro-5 x parameter description setting range default menu path operating mode operating mode norm de-energ, norm energ norm de-energ [device para /relay outputs /ro-5 x2 /ro 1] t-off delay switch off delay 0.00 - 300.00s 0.2s [device para /relay outputs /ro-5 ...

Page 107

Edr-3000 im02602003e parameter description setting range default menu path inverting 7 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-5 x2 /ro 1] operating mode operating mode norm de-energ, norm energ norm de-energ [device para /relay output...

Page 109

Edr-3000 im02602003e parameter description setting range default menu path assignment 7 assignment 1..N, assignment list -.- [device para /relay outputs /ro-5 x2 /ro 2] inverting 7 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-5 x2 /ro 2] op...

Page 111

Edr-3000 im02602003e parameter description setting range default menu path inverting 6 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-5 x2 /ro 3] assignment 7 assignment 1..N, assignment list -.- [device para /relay outputs /ro-5 x2 /ro 3] in...

Page 113

Edr-3000 im02602003e parameter description setting range default menu path assignment 6 assignment 1..N, assignment list -.- [device para /relay outputs /ro-5 x2 /ro 4] inverting 6 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-5 x2 /ro 4] as...

Page 115

Edr-3000 im02602003e parameter description setting range default menu path inverting 5 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-5 x2 /ro 5] assignment 6 assignment 1..N, assignment list -.- [device para /relay outputs /ro-5 x2 /ro 5] in...

Page 117

Edr-3000 im02602003e input states of ro-5 x name description assignment via ro1.1 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 1] ro1.2 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 1] ro1.3 module input state: assignment [device para /relay outpu...

Page 119

Edr-3000 im02602003e name description assignment via ro3.2 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 3] ro3.3 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 3] ro3.4 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 3] ro3....

Page 121

Edr-3000 im02602003e name description assignment via ro5.4 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 5] ro5.5 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 5] ro5.6 module input state: assignment [device para /relay outputs /ro-5 x2 /ro 5] ro5....

Page 123

Edr-3000 im02602003e ro-3zi x - settings ro-3zi x2 direct commands of ro-3zi x parameter description setting range default menu path disarmed this is the second step, after the "disarmed ctrl" has been activated, that is required to disarm the relay outputs. This will disarm those relay outputs that...

Page 125

Edr-3000 im02602003e global protection parameters of ro-3zi x parameter description setting range default menu path operating mode operating mode norm de-energ, norm energ norm de-energ [device para /relay outputs /ro-3zi x2 /ro 1] t-off delay switch off delay 0.00 - 300.00s 0.2s [device para /relay...

Page 127

Edr-3000 im02602003e parameter description setting range default menu path inverting 7 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-3zi x2 /ro 1] operating mode operating mode norm de-energ, norm energ norm de-energ [device para /relay outp...

Page 129

Edr-3000 im02602003e parameter description setting range default menu path assignment 7 assignment 1..N, assignment list -.- [device para /relay outputs /ro-3zi x2 /ro 2] inverting 7 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-3zi x2 /ro 2...

Page 131

Edr-3000 im02602003e parameter description setting range default menu path inverting 6 inverting of the state of the assigned signal. Inactive, active inactive [device para /relay outputs /ro-3zi x2 /ro 3] assignment 7 assignment 1..N, assignment list -.- [device para /relay outputs /ro-3zi x2 /ro 3...

Page 133

Edr-3000 im02602003e input states of ro-3zi x name description assignment via ro1.1 module input state: assignment [device para /relay outputs /ro-3zi x2 /ro 1] ro1.2 module input state: assignment [device para /relay outputs /ro-3zi x2 /ro 1] ro1.3 module input state: assignment [device para /relay...

Page 135

Edr-3000 im02602003e name description assignment via ro3.2 module input state: assignment [device para /relay outputs /ro-3zi x2 /ro 3] ro3.3 module input state: assignment [device para /relay outputs /ro-3zi x2 /ro 3] ro3.4 module input state: assignment [device para /relay outputs /ro-3zi x2 /ro 3...

Page 137

Edr-3000 im02602003e led configuration the leds can be configured within menu: [device para/leds/group x] attention must be paid to insure that there are no overlapping functions due to double or multiple led assignment of colors and flashing codes. If leds are configured as » latched= active«, they...

Page 139

Edr-3000 im02602003e www.Eaton.Com 127 in ac ti ve a ct iv e l a tc h e d a ss ig nm e nt 1 in ve rt in g 1 a ss ig nm e nt 2 in ve rt in g 2 a ss ig nm e nt 3 in ve rt in g 3 a ss ig nm e nt 4 in ve rt in g 4 a ss ig nm e nt 5 in ve rt in g 5 le d a ct iv e c ol o r le d in ac tiv e c ol o r o r o ...

Page 141

Edr-3000 im02602003e led settings leds group a device parameters of the leds parameter description setting range default menu path latched defines whether the led will be latched when it picks up. Inactive, active active [device para /leds /leds group a /led 1] ack signal acknowledgment signal for t...

Page 143

Edr-3000 im02602003e parameter description setting range default menu path led active color the led lights up in this color if the state of the or- assignment of the signals is true. Green, red, red flash, green flash, - red [device para /leds /leds group a /led 2] led inactive color the led lights ...

Page 145

Edr-3000 im02602003e parameter description setting range default menu path assignment 1 assignment 1..N, assignment list 50p[1].Trip [device para /leds /leds group a /led 3] inverting 1 inverting of the state of the assigned signal. Inactive, active inactive [device para /leds /leds group a /led 3] ...

Page 147

Edr-3000 im02602003e parameter description setting range default menu path inverting 2 inverting of the state of the assigned signal. Inactive, active inactive [device para /leds /leds group a /led 4] assignment 3 assignment 1..N, assignment list -.- [device para /leds /leds group a /led 4] invertin...

Page 149

Edr-3000 im02602003e parameter description setting range default menu path assignment 4 assignment 1..N, assignment list -.- [device para /leds /leds group a /led 5] inverting 4 inverting of the state of the assigned signal. Inactive, active inactive [device para /leds /leds group a /led 5] assignme...

Page 151

Edr-3000 im02602003e parameter description setting range default menu path inverting 5 inverting of the state of the assigned signal. Inactive, active inactive [device para /leds /leds group a /led 6] latched defines whether the led will be latched when it picks up. Inactive, active inactive [device...

Page 153

Edr-3000 im02602003e led input states name description assignment via led1.1 module input state: led [device para /leds /leds group a /led 1] led1.2 module input state: led [device para /leds /leds group a /led 1] led1.3 module input state: led [device para /leds /leds group a /led 1] led1.4 module ...

Page 155

Edr-3000 im02602003e name description assignment via acknow sig 3 module input state: acknowledgment signal (only for automatic acknowledgment). [device para /leds /leds group a /led 3] led4.1 module input state: led [device para /leds /leds group a /led 4] led4.2 module input state: led [device par...

Page 157

Edr-3000 im02602003e name description assignment via acknow sig 6 module input state: acknowledgment signal (only for automatic acknowledgment). [device para /leds /leds group a /led 6] led7.1 module input state: led [device para /leds /leds group a /led 7] led7.2 module input state: led [device par...

Page 159

Edr-3000 im02602003e item graphic name description 1 (example for an insert) leds group a basically there are 7 programmable leds provided for user to configure, the choice for each programmable led can be any signal from the global assignment list, which includes all internal operation states of ea...

Page 161

Edr-3000 im02602003e item graphic name description 6 info key (signals/messages ) looking through the present led assignment. The direct select key can be activated at any time. If the info key is actuated again, the user will leave the led menu. Here only the first assignments of the leds will be s...

Page 163

Edr-3000 im02602003e basic menu control the graphic user interface is equivalent to a hierarchical structured menu tree. For access to the individual sub-menus, the »softkeys«/navigation keys are used. The function of the »softkeys« can be found as symbol in the footer of the display. Softkey descri...

Page 165: Powerport-E

Edr-3000 im02602003e powerport-e powerport-e is software that is used to configure a device and read data from a device. Powerport-e provides the following: menu controlled parameter setting including validity checks; off-line configuration of all relay types; reading and evaluation of statistical d...

Page 167

Edr-3000 im02602003e setting up the connection pc - device set up a connection via a serial interface after installation of the software, the »connection pc/notebook to the device« has to be initially configured so that the user is able to read device data or re-write them into the device by means o...

Page 169

Edr-3000 im02602003e establishing the serial connection via a usb-/rs232-adapter if your pc/notebook does not have an rs-232 interface, an usb-/rs232-adapter+null modem cable can be used. Only an adapter approved by eaton corporation may be used. First install the adapter (with the related driver th...

Page 171

Edr-3000 im02602003e www.Eaton.Com 159 tcp/ip parameter setting and evaluation via tcp/ip powerport-e ip -a d d re ss device example.

Page 173

Edr-3000 im02602003e set-up a connection via modbus tunnel establishing a connection via a gateway (tcp/ip)/modbus rtu to the device is only possible if your device is equipped with an ethernet interface (rj45). Contact your it administrator in order to establish the network connection. Part 1: if y...

Page 175

Edr-3000 im02602003e connected to the device and calling up websites at the same time* *=applies to serial connections only (rs232) in principle, it is possible to call up websites while there is an active connection to the device. If your computer has no direct connection to the internet, that mean...

Page 177

Edr-3000 im02602003e powerport-e persistent connection problems in the case of persistent connection problems, the user should remove all connection settings and establish them again. In order to remove all connection settings, please proceed as follows. 1. Remove the settings for the dial-up networ...

Page 179

Edr-3000 im02602003e in order to (re-)transfer changed parameters into the device, select »transfer all parameters into the device« in the »device« menu. Confirm the safety inquiry »shall the parameters be overwritten into the device?«. Enter the password for setting parameters in the pop-up window....

Page 181

Edr-3000 im02602003e off-line device planning via powerport-e in order to be able to transmit a parameter file (e.G.: created off-line) into the device, the following information must be located: type code (written on the top of the device/type label); and version of the device model (can be found i...

Page 183

Edr-3000 im02602003e measuring values read out measured values in the »operation/measured values« menu, both measured and calculated values can be viewed. The measured values are ordered by »standard values« and »special values« (depending on the type of device). Read out of measured values via powe...

Page 185

Edr-3000 im02602003e energy units (applies only for devices with energy measurement) by means of the parameter » energy units« the user can determine how measured values are to be displayed within the hmi and powerport-e : energy auto scaling kwh, kvarh or kvah mwh, mvarh or mvah gwh, gvarh or gvah ...

Page 187

Edr-3000 im02602003e value description menu path angle ic measured value (calculated): angle of phasor ic [operation /measured values /current fund.] angle ix meas measured value (calculated): angle of phasor ix meas [operation /measured values /current fund.] angle ir calc measured value (calculate...

Page 189

Edr-3000 im02602003e statistics statistics in menu »operation/statistics« the min., max. And mean values of the measured and calculated measured quantities can be found. Configuration of the minimum and maximum values the calculation of the minimum and maximum values will be started: when a reset si...

Page 191

Edr-3000 im02602003e configuration of the voltage based average value calculation* *=availability depends on the ordered device code. Voltage based average values time period for the calculation of the average values start options reset of the average and peak values configuration options where to c...

Page 193

Edr-3000 im02602003e parameter description setting range default menu path resfc i demand resetting of statistics - current demand (avg, peak avg) 1..N, assignment list -.- [device para /statistics /demand /current demand] duration i demand recording time only available if: start i demand via: = dur...

Page 195

Edr-3000 im02602003e signals of the statistics module signal description resfc all signal: resetting of all statistic values (current demand, power demand, min, max) resfc i demand signal: resetting of statistics - current demand (avg, peak avg) resfc max signal: resetting of all maximum values resf...

Page 197

Edr-3000 im02602003e value description menu path ib avg rms ib average value (rms) [operation /statistics /demand /current demand] ib min rms ib minimum value (rms) [operation /statistics /min /ct] ic max rms ic maximum value (rms) [operation /statistics /max /ct] ic avg rms ic average value (rms) [...

Page 199

Edr-3000 im02602003e system alarms available elements: sysa within the system alarms menu [sysa] the user can configure: general settings (activate/inactivate the demand management, optional assign a signal, that will block the demand management); demand management (current); and thd protection. Ple...

Page 201

Edr-3000 im02602003e www.Eaton.Com 189 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 window configuration = sliding window configuration = fixed sliding sliding t-del...

Page 203

Edr-3000 im02602003e device planning parameters of the demand management parameter description options default menu path mode mode do not use, use use [device planning] signals of the demand management (states of the outputs) signal description active signal: active exblo signal: external blocking a...

Page 205

Edr-3000 im02602003e states of the inputs of the demand management name description assignment via exblo-i module input state: external blocking [sysa /general settings] www.Eaton.Com 193.

Page 207

Edr-3000 im02602003e options for individual acknowledgments for latched signals: individual acknowledgment leds relay output pending trip command via a signal from the assignment list (e.G.: a digital input), a single ... Can be acknowledged. Single led: where? Within the configuration menu of this ...

Page 209

Edr-3000 im02602003e external acknowledgments within the [ex acknowledge] menu, the user can assign a signal (e.G.: the state of a digital input) from the assignment list that: • acknowledges all (acknowledgeable) leds at once; • acknowledges all (acknowledgeable) output relays at once; or • acknowl...

Page 211

Edr-3000 im02602003e name description logic.Le2.Gate out signal: output of the logic gate logic.Le2.Timer out signal: timer output logic.Le2.Out signal: latched output (q) logic.Le2.Out inverted signal: negated latched output (q not) logic.Le3.Gate out signal: output of the logic gate logic.Le3.Time...

Page 213

Edr-3000 im02602003e name description logic.Le20.Out signal: latched output (q) logic.Le20.Out inverted signal: negated latched output (q not) logic.Le21.Gate out signal: output of the logic gate logic.Le21.Timer out signal: timer output logic.Le21.Out signal: latched output (q) logic.Le21.Out inver...

Page 215

Edr-3000 im02602003e name description logic.Le39.Gate out signal: output of the logic gate logic.Le39.Timer out signal: timer output logic.Le39.Out signal: latched output (q) logic.Le39.Out inverted signal: negated latched output (q not) logic.Le40.Gate out signal: output of the logic gate logic.Le4...

Page 217

Edr-3000 im02602003e name description logic.Le57.Out signal: latched output (q) logic.Le57.Out inverted signal: negated latched output (q not) logic.Le58.Gate out signal: output of the logic gate logic.Le58.Timer out signal: timer output logic.Le58.Out signal: latched output (q) logic.Le58.Out inver...

Page 219

Edr-3000 im02602003e name description logic.Le76.Gate out signal: output of the logic gate logic.Le76.Timer out signal: timer output logic.Le76.Out signal: latched output (q) logic.Le76.Out inverted signal: negated latched output (q not) logic.Le77.Gate out signal: output of the logic gate logic.Le7...

Page 221

Edr-3000 im02602003e status display in the status display within the »operation« menu, the present state of all signals can be viewed. This means the user is able to see if the individual signals are active or inactive at that moment. The user can see all signals sorted by protective elements/module...

Page 223

Edr-3000 im02602003e recorders waveform recorder waveform rec the waveform recorder works with 32 samples per cycle. It can be started by one of eight start events (selection from the »assignment list«/or-logic). The waveform record contains the measuring values including the pre-trigger time. By me...

Page 225

Edr-3000 im02602003e www.Eaton.Com 213 start 1 t t 0 1 0 1 300 ms 1200 ms pre-trigger time t 0 1 500 ms post-trigger time t 0 1 2000 ms t-rec t 0 1 2000 ms max file size start 1 = prot.Pickup start 2 = -.- start 3 = -.- start 4 = -.- start 5 = -.- start 6 = -.- start 7 = -.- start 8 = -.- post-trigg...

Page 227

Edr-3000 im02602003e read out of w aveform records within the » operation/waveform rec« menu, the user can: • detect the accumulated waveform records. Within the »operation/recorders/man trigger« menu, the user can trigger the waveform recorder manually. To read out the w aveform recorder with power...

Page 229

Edr-3000 im02602003e direct commands of the waveform recorder module parameter description setting range default menu path man. Trigger manual trigger false, true false [operation /recorders /man. Trigger] res all rec reset all records inactive, active inactive [operation /reset] global protection p...

Page 231

Edr-3000 im02602003e waveform recorder module input states name description assignment via start1-i state of the module input:: trigger event / start recording if: [device para /recorders /waveform rec] start2-i state of the module input:: trigger event / start recording if: [device para /recorders ...

Page 233

Edr-3000 im02602003e special parameters of the waveform recorder value description default size menu path rec state recording state ready ready, recording, writing file, trigger blo [operation /status display /recorders /waveform rec] error code error code ok ok, write err, clear fail, calculation e...

Page 235

Edr-3000 im02602003e definitions time to trip: time between first alarm (prot.Pickup) and first trip (prot.Trip) decision fault duration: time period from the rising edge of the general pickup ( »p rot .P ickup « ) signal up to the falling edge of the general pickup signal. Please note that general ...

Page 237

Edr-3000 im02602003e how to close the overlay/popup? By using softkey »ok«. How to find out fast, if a fault has lead to a trip or not? Faults that lead to a trip will be indicated by a flash icon (right side) within the overview menu of the fault recorder. Which fault record pops up? The newest fau...

Page 239

Edr-3000 im02602003e how to set up the fault recorder the » record-mode« will determine if trips only cause a fault record or if also alarms without a consecutively trip should cause a fault record. This parameter is to be set within menu [device para\recorders\fault rec] how to navigate within the ...

Page 241

Edr-3000 im02602003e direct commands of the fault recorder module parameter description setting range default menu path res all rec reset all records inactive, active inactive [operation /reset] global protection parameters of the fault recorder module parameter description setting range default men...

Page 243

Edr-3000 im02602003e read out the event recorder call up the » main menu«. Call up the sub-menu »operation/recorders/event rec« . Select an event. To read out the event recorder via powerport-e if powerport-e is not running, please start the application. If the device data have not been loaded, clic...

Page 245

Edr-3000 im02602003e direct commands of the event recorder module parameter description setting range default menu path res all rec reset all records inactive, active inactive [operation /reset] event recorder module signals signal description res all rec signal: all records deleted www.Eaton.Com 23...

Page 247

Edr-3000 im02602003e selection list for trending name description -.- no assignment ct.Ia rms measured value: phase current (rms) ct.Ib rms measured value: phase current (rms) ct.Ic rms measured value: phase current (rms) ct.Ix meas rms measured value (measured): ix (rms) ct.Ir calc rms measured val...

Page 249

Edr-3000 im02602003e parameter description setting range default menu path observed value10 observed value10 1..N, trendreclist -.- [device para /recorders /trend rec] www.Eaton.Com 237.

Page 251

Edr-3000 im02602003e time synchronization timezones the device gives the user the ability to synchronize the device with a central time generator. This provides the following advantages: the time does not drift from the reference time. A continuously accumulating deviation of the reference time ther...

Page 253

Edr-3000 im02602003e selection of timezone and synchronisation protocol the protection relay masters both utc and local time. This means that the device can be synchronised with utc time while using local time for user display. Time synchronisation with utc time (recommended): time synchronisation i...

Page 255

Edr-3000 im02602003e parameter description setting range default menu path summertime w place of selected day in month (for clock change summertime) only available if: dst manual = active first, second, third, fourth, last last [device para /time /timezone] summertime h hour of clock change summerti...

Page 257

Edr-3000 im02602003e parameter description setting range default menu path time zones time zones utc+14 kiritimati, utc+13 rawaki, utc+12.75 chatham island, utc+12 wellington, utc+11.5 kingston, utc+11 port vila, utc+10.5 lord howe island, utc+10 sydney, utc+9.5 adelaide, utc+9 tokyo, utc+8 hong kon...

Page 259

Edr-3000 im02602003e sntp sntp important pre-condition: the device needs to have access to an sntp server via the connected network. This server preferably should be installed locally. Principle – general use sntp is a standard protocol for time synchronization via a network. At minimum, one sntp se...

Page 261

Edr-3000 im02602003e fault analysis if there is no sntp signal for more than 120 seconds., the sntp status changes from “active” to “inactive” and an entry in the event recorder will be set. The sntp functionality can be checked in the [operation/status display/time sync./sntp] menu. If the sntp sta...

Page 263

Edr-3000 im02602003e parameter description setting range default menu path ip byte4 ip1.Ip2.Ip3.Ip4 0 - 255 0 [device para /time /timesync /sntp] server2 server 2 inactive, active inactive [device para /time /timesync /sntp] ip byte1 ip1.Ip2.Ip3.Ip4 0 - 255 0 [device para /time /timesync /sntp] ip b...

Page 265

Edr-3000 im02602003e value description default size menu path noofhighoffs service counter: total number of high offsets. 0 0 - 9999999999 [operation /count and revdata /timesync /sntp] noofinttimeouts service counter: total number of internal timeouts. 0 0 - 9999999999 [operation /count and revdata...

Page 267

Edr-3000 im02602003e irig-b00x irig-b requirement: an irig-b00x time code generator is needed. Irig-b004 and higher will support/transmit the “year information”. If you are using an irig time code that does not support the “year information” (irig-b000, irig-b001, irig-b002, irig-b003), you have to ...

Page 269

Edr-3000 im02602003e device planning parameters of the irig-b00x parameter description options default menu path mode mode do not use, use use [device planning] direct commands of the irig-b00x parameter description setting range default menu path res irig-b cr resetting of the diagnosis counters: i...

Page 271

Edr-3000 im02602003e value description default size menu path edges edges 0 0 - 65535 [operation /count and revdata /timesync /irig-b] www.Eaton.Com 259.

Page 273

Edr-3000 im02602003e tcp/ip settings warning: mixing up ip addresses (in case there is more than one protective device within the tcp/ip network or establishing an unintentional wrong connection to a protective device based on a wrong entered ip address. Transferring parameters into the wrong protec...

Page 275

Edr-3000 im02602003e global protection parameters of the system parameter description setting range default menu path pset-switch switching parameter set ps1, ps2, ps3, ps4, pss via inp fct, pss via comm pss via inp fct [protection para /pset-switch] ps1: activated by this setting group will be the ...

Page 277

Edr-3000 im02602003e system module input states name description assignment via ack led-i module input state: leds acknowledgment by digital input. [device para /ex acknowledge] ack ro-i module input state: acknowledgment of the relay outputs. [device para /ex acknowledge] ack comm-i module input st...

Page 279

Edr-3000 im02602003e special values of the system module value description menu path build build [device para /version] version version [device para /version] operating hours cr operating hours counter of the protective device [operation /count and revdata /sys] www.Eaton.Com 267.

Page 281

Edr-3000 im02602003e modbus rtu part 1: configuration of the devices call up »device parameter/modbus« and set the following communication parameters: slave address, to allow clear identification of the device; and baud rate. Also, select the rs485 interface-related parameters such as: number of dat...

Page 283

Edr-3000 im02602003e direct commands of the modbus ® parameter description setting range default menu path res diagn cr all modbus diagnosis counters will be reset. Inactive, active inactive [operation /reset] global protection parameters of the modbus ® parameter description setting range default m...

Page 285

Edr-3000 im02602003e modbus ® module signals (output states) some signals (that are active for a short time only) have to be acknowledged separately (e.G.: trip signals) by the communication system. Signal description transmission signal: communication active comm cmd 1 communication command comm cm...

Page 287

Edr-3000 im02602003e iec 61850 iec61850 introduction to understand the functioning and mode of operation of a substation in an iec 61850 automation environment, it is useful to compare the commissioning steps with those of a conventional substation in a modbus tcp environment. In a conventional subs...

Page 289

Edr-3000 im02602003e generation/export of a device specific icd file each eaton iec 61850 capable device includes a description of its own functionality and communications skills in the form of an ied capability description (*.Icd) file. This file can be exported as follows and be used for the confi...

Page 291

Edr-3000 im02602003e device planning parameters of the iec 61850 parameter description options default menu path mode mode do not use, use use [device planning] www.Eaton.Com 279.

Page 293

Edr-3000 im02602003e parameter description setting range default menu path virtualoutput7 virtual output. This signal can be assigned or visualized via the scd file to other devices within the iec61850 substation. 1..N, assignment list -.- [device para /iec61850] virtualoutput8 virtual output. This ...

Page 295

Edr-3000 im02602003e parameter description setting range default menu path virtualoutput27 virtual output. This signal can be assigned or visualized via the scd file to other devices within the iec61850 substation. 1..N, assignment list -.- [device para /iec61850] virtualoutput28 virtual output. Thi...

Page 297

Edr-3000 im02602003e name description assignment via virtout18-i module input state: binary state of the virtual output (ggio) [device para /iec61850] virtout19-i module input state: binary state of the virtual output (ggio) [device para /iec61850] virtout20-i module input state: binary state of the...

Page 299

Edr-3000 im02602003e iec 61850 module values value description default size menu path noofgooserxall total number of received goose messages including messages for other devices (subscribed and not subscribed messages). 0 0 - 9999999999 [operation /count and revdata /iec61850] noofgooserxsubscr ibed...

Page 301

Edr-3000 im02602003e values of the iec 61850 value description default size menu path goosepublisherstate state of the goose publisher (on or off) off off, on, error [operation /status display /iec61850] goosesubscriberstat e state of the goose subscriber (on or off) off off, on, error [operation /s...

Page 303

Edr-3000 im02602003e system parameters system parameters are part of the “device parameter tree”. System parameters comprise the essential, basic settings of your switchboard such as rated frequency and transformer ratios. Protection parameters please note that by deactivating, for example protectiv...

Page 305

Edr-3000 im02602003e adaptive parameter sets www.Eaton.Com 293 ps et-s witc h ad ap ts et p ro te ct io n p ar a p ar am e te r s et 4 a ct iv e/ in ac tiv e a ct iv e / in a ct iv e a ct iv e/ in a ct iv e a ct iv e/ in a ct iv e a ct iv e /in a ct iv e p ar am e te r s et 3 a ct iv e/ in ac tiv e ...

Page 307

Edr-3000 im02602003e adaptive parameter set activation signals name description -.- no assignment sotf.Enabled signal: switch onto fault enabled. This signal can be used to modify overcurrent protection settings. Clpu.Enabled signal: cold load enabled ar.Running signal: auto reclosing running ar.Pre...

Page 309

Edr-3000 im02602003e name description logic.Le13.Timer out signal: timer output logic.Le13.Out signal: latched output (q) logic.Le13.Out inverted signal: negated latched output (q not) logic.Le14.Gate out signal: output of the logic gate logic.Le14.Timer out signal: timer output logic.Le14.Out signa...

Page 311

Edr-3000 im02602003e name description logic.Le31.Out inverted signal: negated latched output (q not) logic.Le32.Gate out signal: output of the logic gate logic.Le32.Timer out signal: timer output logic.Le32.Out signal: latched output (q) logic.Le32.Out inverted signal: negated latched output (q not)...

Page 313

Edr-3000 im02602003e name description logic.Le50.Timer out signal: timer output logic.Le50.Out signal: latched output (q) logic.Le50.Out inverted signal: negated latched output (q not) logic.Le51.Gate out signal: output of the logic gate logic.Le51.Timer out signal: timer output logic.Le51.Out signa...

Page 315

Edr-3000 im02602003e name description logic.Le68.Out inverted signal: negated latched output (q not) logic.Le69.Gate out signal: output of the logic gate logic.Le69.Timer out signal: timer output logic.Le69.Out signal: latched output (q) logic.Le69.Out inverted signal: negated latched output (q not)...

Page 317

Edr-3000 im02602003e access authorizations (access areas) passwords – areas the following table shows the access areas and the authorization passwords that they require in order to access them. Area symbol authorization password access to: read only-lv0 level 0 provides read only access to all setti...

Page 319

Edr-3000 im02602003e during setting parameters the c-button will be used for the cancelling of parameter changes. Because of that it is not possible, to acknowledge (leds, output relays...) as long as there are non saved (cached only) parameters. Acknowledgement can only be executed, when the upper ...

Page 321

Edr-3000 im02602003e how to find out what access areas/levels are unlocked? The menu [device para\access levels] provides the information, which access areas (authorizations) are currently unlocked. As soon as there is an unlocked access area (authorization) above »read only-lv0« , this will be indi...

Page 323

Edr-3000 im02602003e adaptive parameters via hmi the use of adaptive parameters via the hmi (panel) differs a bit to the use via powerport-e. Adaptive parameters can be also used via the hmi (instead of using the recommended powerport-e ). The principle method of using them via the hmi is as follows...

Page 325

Edr-3000 im02602003e the screen shot above shows the adaptive setting configurations following applications based on only one simple overcurrent protection element: 1. Standard set: default settings; 2. Adaptive set 1: sotf application (switch-onto-fault); 3. Adaptive set 2: clpu application (cold l...

Page 327

Edr-3000 im02602003e if the device was not active within the parameter setting mode for a longer time (can be set between 20 – 3600 seconds) it changes into »read only-lv0« mode automatically. This parameter (t-max-edit) can be modified within menu [device para\hmi]. Www.Eaton.Com 315.

Page 329

Edr-3000 im02602003e the passwords are part of the device (fixed assignments). That means, passwords will not be overwritten, if a parameter file is transmitted into a device. Existing passwords are persistent (assined to a device). If an offline created parameter file is transmitted into a device, ...

Page 331

Edr-3000 im02602003e unlocking access areas within the menu [device para\access level] access areas can be unlocked or locked (at the hmi). Changing passwords passwords can be changed at the device in menu [device para/passwords] or by means of the power-port-e s oftware. A password must be a user-d...

Page 333

Edr-3000 im02602003e parameter setting at the hmi every parameter belongs to an access area. Editing and changing of a parameter requires a sufficient access authorization. The user can obtain the required access authorizations by unlocking access areas in advance of parameter changes or context-dep...

Page 335

Edr-3000 im02602003e option 2: context-dependent access authorization navigate to the parameter, that is to be changed. If the parameter is selected, the lower right corner of the display shows a » key« -symbol. This symbol indicates, that the device is still within the »read only lv0« -level, or th...

Page 337

Edr-3000 im02602003e parameter setting via power-port-e power-port-e shows within the windows, where parameters are edited also the required access level for the parameters and settings. The required access authorizations will be verified when the parameter file should be transferred into the protec...

Page 339

Edr-3000 im02602003e additional parameters can be changed if required. There are two options available to transfer changed parameters into the device within menu »device«. 1. »transfer all parameters into the device« . This always requires the supervisor (administrator) password. 2. »transfer only m...

Page 341

Edr-3000 im02602003e signals that can be used for pss name description -.- no assignment di-4p x1.Di 1 signal: digital input di-4p x1.Di 2 signal: digital input di-4p x1.Di 3 signal: digital input di-4p x1.Di 4 signal: digital input di-8p x1.Di 1 signal: digital input di-8p x1.Di 2 signal: digital i...

Page 343

Edr-3000 im02602003e name description logic.Le15.Out inverted signal: negated latched output (q not) logic.Le16.Gate out signal: output of the logic gate logic.Le16.Timer out signal: timer output logic.Le16.Out signal: latched output (q) logic.Le16.Out inverted signal: negated latched output (q not)...

Page 345

Edr-3000 im02602003e name description logic.Le34.Timer out signal: timer output logic.Le34.Out signal: latched output (q) logic.Le34.Out inverted signal: negated latched output (q not) logic.Le35.Gate out signal: output of the logic gate logic.Le35.Timer out signal: timer output logic.Le35.Out signa...

Page 347

Edr-3000 im02602003e name description logic.Le52.Out inverted signal: negated latched output (q not) logic.Le53.Gate out signal: output of the logic gate logic.Le53.Timer out signal: timer output logic.Le53.Out signal: latched output (q) logic.Le53.Out inverted signal: negated latched output (q not)...

Page 349

Edr-3000 im02602003e name description logic.Le71.Timer out signal: timer output logic.Le71.Out signal: latched output (q) logic.Le71.Out inverted signal: negated latched output (q not) logic.Le72.Gate out signal: output of the logic gate logic.Le72.Timer out signal: timer output logic.Le72.Out signa...

Page 351

Edr-3000 im02602003e setting group switch via powerport-e if powerport-e is not running, please start the application. If the device data have not been loaded, click »receive data from the device« in the »device« menu. Double click the »protection para« icon in the navigation tree. Double click the ...

Page 353

Edr-3000 im02602003e comparing parameter files via powerport-e with the help of powerport-e, the user can simply compare/differentiate the currently open parameter/device file against a file on the hard disk. The precondition is that the versions and type of devices match. To compare the parameter f...

Page 355

Edr-3000 im02602003e program mode by means of the program mode , parameter settings can be locked against any changes as long as one or all of the breaker(s) are in the » closed« position. The program mode can be activated within the [system para/general settings/program mode bypass] menu. »both bkr...

Page 357

Edr-3000 im02602003e system parameters – current related parameter description setting range default menu path ct con current transformer connection 3-wire, 4th ct in, 4th ct ig 3-wire [system para /general settings] ct pri nominal current of the primary side of the current transformers. 1 - 50000a ...

Page 359

Edr-3000 im02602003e to block a complete protection module temporarily by an active assignment in order to establish a temporary blockage of a protection module, the parameter »exblo fc« of the module has to be set to »active« . This gives the permission: »this module can be blocked«. Within the gen...

Page 361

Edr-3000 im02602003e activate, deactivate respectively to block temporary protection functions www.Eaton.Com 349 an d in ac tiv e ac tiv e n am e. Fu nc tio n in ac tiv e ac tiv e n am e. Ex bl o fc n am e. A ct iv e pr ot . A ct iv e 1. .N , a ss ig nm en t l is t n am e. Ex bl o 1 n am e. E xb lo ...

Page 363

Edr-3000 im02602003e protection (prot) module prot the »protection« module serves as the outer frame for all other protection modules (i.E.: they are all enclosed by the »protection« module). In the case where the »protection« module is blocked, the complete protective function of the device is disa...

Page 365

Edr-3000 im02602003e each protection element generates its own pickup and trip signals, which are automatically passed onto the »prot« module where the phase based and general (collective) pickup and trip signals are generated. The »prot« module serves as a top level and a common place to group all ...

Page 367

Edr-3000 im02602003e www.Eaton.Com 355 pr ot .P ic ku p p ro t.P ic ku p n am e. Pi ck up n am e. Pi ck up n am e. Pi ck up n am e = e ac h pi ck up o f a m od ul e (e xc ep t f ro m s up er vi si on m od ul es b ut in cl ud in g b f) w ill le ad to a g en er al p ic ku p (c ol le ct iv e pi ck up )...

Page 369

Edr-3000 im02602003e www.Eaton.Com 357 50 r[ 1] ... [n ].P ic ku p* 59 [n ].P ic ku p* p ro t.P ic ku p ix o r i r 51 r[ 1] ... [n ].P ic ku p* p ro t.P ic ku p e ac h p ha se s e le ct iv e p ic ku p o f a m od ul e ( i, ig , v , v x d ep e nd in g o n th e de vi ce t yp e) w ill le a d to a p h as...

Page 371

Edr-3000 im02602003e protection module input states name description assignment via exblo1-i module input state: external blocking1 [protection para /global prot para /prot] exblo2-i module input state: external blocking2 [protection para /global prot para /prot] protection module signals (output st...

Page 373

Edr-3000 im02602003e switchgear/breaker - manager bkr warning: misconfiguration of the breaker could result in death or serious injury. Breaker configuration for the configuration of the breaker, great attention has to be payed to the following steps: • wiring • switching authority • pos indicators ...

Page 375

Edr-3000 im02602003e single line diagram the single line diagram includes the graphically description of the switchgear and its designation (name) as well as its features (short circuit proof or not ...). For displaying in the devices software, the switchgear' designations (e. G. Qa1, qa2, instead o...

Page 377

Edr-3000 im02602003e the following table shows how breaker positions are validated based on 52a and 52b: states of the digital inputs validated breaker positions cinbkr52a-i cinbkr52b-i pos close pos open pos indeterm pos disturb breaker state 0 0 0 0 1 (while a moving timer is running) 0 (while a m...

Page 379

Edr-3000 im02602003e single contact indication – 52b only if only the 52b signal is used for the monitoring of the “open command”, the switch command will start the moving timer. The position indication will indicate an intermediate position. If the moving time elapsed before the switchgear has reac...

Page 381

Edr-3000 im02602003e www.Eaton.Com 369 signal breaker close signal breaker open signal breaker ready trigger [x] trigger [x] trigger [x] b re a ke r breaker open command breaker close command protection trip command position indication: open, close, indeterminated, disturbed trip command 50p[x] trip...

Page 383

Edr-3000 im02602003e interlockings there are three interlocking inputs for each switching direction (open/close) available. Switching into the corresponding switching direction can be inhibited via these inputs. Please note: the protection trip commands and the reclosure command of the auto reclosur...

Page 385

Edr-3000 im02602003e ex open/close if the breaker should be opened or closed by an external signal, the user can assign one signal that will trigger the close and one signal that will trigger the open command (e.G.: digital inputs or output signals of the logics). An applied close command will be ov...

Page 387

Edr-3000 im02602003e global protection parameters of the switchgear/breaker parameter description setting range default menu path cinbkr-52a the breaker is in close-position if the state of the assigned signal is true (52a). 1..N, dig inputs di-4p x1.Di 1 [control /bkr /pos indicatrs wirng] cinbkr-5...

Page 389

Edr-3000 im02602003e parameter description setting range default menu path trigger8 open command to the breaker if the state of the assigned signal becomes true. 1..N, trip cmds 50r[2].Tripcmd [control /bkr /trip manager] trigger9 open command to the breaker if the state of the assigned signal becom...

Page 391

Edr-3000 im02602003e switchgear/breaker input states name description assignment via cinbkr-52a-i module input state: feed-back signal of the bkr (52a) [control /bkr /pos indicatrs wirng] cinbkr-52b-i module input state: feed-back signal of the bkr. (52b) [control /bkr /pos indicatrs wirng] ready-i ...

Page 393

Edr-3000 im02602003e signal description tripcmd signal: trip command ack tripcmd signal: acknowledge trip command bwear slow breaker signal: slow breaker alarm res bwear sl breaker signal: resetting the slow breaker alarm close cmd signal: close command issued to the switchgear. Depending on the set...

Page 395

Edr-3000 im02602003e direct commands of the switching authority parameter description setting range default menu path switching authority switching authority none, local, remote, local and remote local [control /general settings] signals of the switching authority signal description local switching ...

Page 397

Edr-3000 im02602003e breaker wear curve in order to keep the breaker in good working condition, the breaker needs to be monitored. The breaker health (operation life) depends above all on: the number of close/open cycles and the amplitudes of the interrupting currents. The user has to maintain the b...

Page 399

Edr-3000 im02602003e parameter description setting range default menu path count2 open counts allowed #2 only available if:bwear curve fc = active 1 - 32000 10000 [control /bkr /bwear] current3 interrupted current level #3 only available if:bwear curve fc = active 0.00 - 2000.00ka 1.15ka [control /b...

Page 401

Edr-3000 im02602003e breaker wear signals (output states) signal description operations alarm signal: service alarm, too many operations isum intr trip: ia signal: maximum permissible summation of the interrupting (tripping) currents exceeded: ia isum intr trip: ib signal: maximum permissible summat...

Page 403

Edr-3000 im02602003e direct commands of the breaker wear module parameter description setting range default menu path res tripcmdcr resetting of the counter: total number of trip commands inactive, active inactive [operation /reset] res isum trip reset summation of the tripping currents inactive, ac...

Page 405

Edr-3000 im02602003e name description logic.Le9.Out signal: latched output (q) logic.Le9.Out inverted signal: negated latched output (q not) logic.Le10.Gate out signal: output of the logic gate logic.Le10.Timer out signal: timer output logic.Le10.Out signal: latched output (q) logic.Le10.Out inverte...

Page 407

Edr-3000 im02602003e name description logic.Le28.Gate out signal: output of the logic gate logic.Le28.Timer out signal: timer output logic.Le28.Out signal: latched output (q) logic.Le28.Out inverted signal: negated latched output (q not) logic.Le29.Gate out signal: output of the logic gate logic.Le2...

Page 409

Edr-3000 im02602003e name description logic.Le46.Out signal: latched output (q) logic.Le46.Out inverted signal: negated latched output (q not) logic.Le47.Gate out signal: output of the logic gate logic.Le47.Timer out signal: timer output logic.Le47.Out signal: latched output (q) logic.Le47.Out inver...

Page 411

Edr-3000 im02602003e name description logic.Le65.Gate out signal: output of the logic gate logic.Le65.Timer out signal: timer output logic.Le65.Out signal: latched output (q) logic.Le65.Out inverted signal: negated latched output (q not) logic.Le66.Gate out signal: output of the logic gate logic.Le6...

Page 413

Edr-3000 im02602003e control - example: switching of a breaker ctrl the following example shows how to switch a breaker via the hmi at the device. Change into the menu »control« by pushing the »right arrow« softkey. Change to the control page by pushing the »right arrow« softkey. Information only: o...

Page 415

Edr-3000 im02602003e the switching command will be given to the breaker. The display shows the intermediate position of the switchgear. It will be shown on the display when the switchgear reaches the new end position. Further possible switching operations (open) will be displayed by softkeys. Notice...

Page 417

Edr-3000 im02602003e www.Eaton.Com 405 50 p[ 1] ... [n ] n am e = 50 p [1 ].. .[n ] fu nd . Rm s na m e. C rit er io n φ n am e. Tr ip c m d n am e. P ic ku p ia n am e. P ic ku p ib n am e. P ic ku p ic n am e. Tr ip ih 2. B lo p ha se a ih 2. Bl o ph as e b ih 2. Bl o ph as e c p le a se r ef er t...

Page 419

Edr-3000 im02602003e parameter description setting range default menu path adaptset 3 assignment adaptive parameter 3 adaptset -.- [protection para /global prot para /i-prot /50p[1]] adaptset 4 assignment adaptive parameter 4 adaptset -.- [protection para /global prot para /i-prot /50p[1]] www.Eaton...

Page 421

Edr-3000 im02602003e parameter description setting range default menu path t tripping delay only available if: characteristic = deft 0.00 - 300.00s 50p[1]: 0s 50p[2]: 0.25s 50p[3]: 0.25s [protection para / /i-prot /50p[1]] www.Eaton.Com 409.

Page 423

Edr-3000 im02602003e 50p module signals (output states) signal description active signal: active exblo signal: external blocking rvs blo signal: reverse blocking blo tripcmd signal: trip command blocked exblo tripcmd signal: external blocking of the trip command pickup ia signal: pickup ia pickup ib...

Page 425

Edr-3000 im02602003e 51p - inv overcurrent-protection elements 51p[1] ,51p[2] ,51p[3] if using inrush blockings, the tripping delay of the current protection functions must be at least 30 ms or more in order to prevent faulty trippings (applies only to devices which are equipped with inrush protecti...

Page 427

Edr-3000 im02602003e device planning parameters of the 51p module parameter description options default menu path mode mode 51p[1]: non-directional 51p[2]: do not use, non-directional 51p[3]: do not use, non-directional non-directional [device planning] global protection parameters of the 51p module...

Page 429

Edr-3000 im02602003e setting group parameters of the 51p module parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active 51p[1]: active 51p[2]: active 51p[3]: inactive [protection para / /i-prot /51p[1]] exblo fc activate...

Page 431

Edr-3000 im02602003e 51p module input states name description assignment via exblo1-i module input state: external blocking1 [protection para /global prot para /i-prot /51p[1]] exblo2-i module input state: external blocking2 [protection para /global prot para /i-prot /51p[1]] exblo tripcmd-i module ...

Page 433

Edr-3000 im02602003e commissioning: overcurrent protection, non-directional [ansi 51p] object to be tested signals to be measured for each current protection element: the threshold values, total tripping time (recommended), or alternatively tripping delays and the drop-out ratios; each time 3 x sing...

Page 435

Edr-3000 im02602003e www.Eaton.Com 423 50 x [1 ].. .[n ] n am e = 50 x [1 ].. .[n ] n am e. Tr ip c m d n am e. Tr ip p le as e r ef er to d ia gr am : b lo ck in gs ** n am e. P ic ku p p le as e r ef er to d ia gr am : tr ip b lo ck in gs (e le m en t i s no t d ea ct iva te d an d no a ct ive b l...

Page 437

Edr-3000 im02602003e parameter description setting range default menu path adaptset 3 assignment adaptive parameter 3 adaptset -.- [protection para /global prot para /i-prot /50x[1]] adaptset 4 assignment adaptive parameter 4 adaptset -.- [protection para /global prot para /i-prot /50x[1]] www.Eaton...

Page 439

Edr-3000 im02602003e parameter description setting range default menu path pickup (sensitive) if the pickup value is exceeded, the module/element will be started. 0.002 - 2.000in 0.02in [protection para / /i-prot /50x[1]] t tripping delay only available if: characteristic = deft 0.00 - 300.00s 0.5s ...

Page 441

Edr-3000 im02602003e 50x ground fault protection signals (output states) signal description active signal: active exblo signal: external blocking rvs blo signal: reverse blocking blo tripcmd signal: trip command blocked exblo tripcmd signal: external blocking of the trip command pickup signal: picku...

Page 443

Edr-3000 im02602003e 51x inv measured ground fault protection elements 51x[1] ,51x[2] all ground current elements are identically structured. For each element the following characteristics are available: • ninv (iec/ xinv ); • vinv (iec/ xinv ); • linv (iec/ xinv ); • einv (iec/ xinv ); • minv (ansi...

Page 445

Edr-3000 im02602003e device planning parameters of the 51x ground fault protection parameter description options default menu path mode mode 51x[1]: non-directional 51x[2]: do not use, non-directional non-directional [device planning] global protection parameters of the 51x ground fault protection p...

Page 447

Edr-3000 im02602003e setting group parameters of the 51x ground fault protection parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active active [protection para / /i-prot /51x[1]] exblo fc activate (allow) or inactivate ...

Page 449

Edr-3000 im02602003e 51x ground fault protection input states name description assignment via exblo1-i module input state: external blocking1 [protection para /global prot para /i-prot /51x[1]] exblo2-i module input state: external blocking2 [protection para /global prot para /i-prot /51x[1]] exblo ...

Page 451

Edr-3000 im02602003e commissioning: ground fault protection – non-directional [ansi 51x] please test the non-directional ground overcurrent analog to the non-directional phase overcurrent protection. Www.Eaton.Com 439.

Page 453

Edr-3000 im02602003e www.Eaton.Com 441 n am e. Tr ip c m d n am e. Tr ip p le a se re fe r to d ia g ra m : b lo ck in g s* * n am e. Pi ck up p le a se re fe r to d ia g ra m : tr ip b lo ck in gs (e le m en t i s no t d ea ct iv at ed a nd n o ac tiv e bl oc kin g si gn al s) (t rip pi ng c om m a...

Page 455

Edr-3000 im02602003e parameter description setting range default menu path adaptset 3 assignment adaptive parameter 3 adaptset -.- [protection para /global prot para /i-prot /50r[1]] adaptset 4 assignment adaptive parameter 4 adaptset -.- [protection para /global prot para /i-prot /50r[1]] www.Eaton...

Page 457

Edr-3000 im02602003e parameter description setting range default menu path t tripping delay only available if: characteristic = deft 0.00 - 300.00s 0.5s [protection para / /i-prot /50r[1]] www.Eaton.Com 445.

Page 459

Edr-3000 im02602003e 50r ground fault protection signals (output states) signal description active signal: active exblo signal: external blocking rvs blo signal: reverse blocking blo tripcmd signal: trip command blocked exblo tripcmd signal: external blocking of the trip command pickup signal: picku...

Page 461

Edr-3000 im02602003e 51r inv calculated ground fault protection elements 51r[1] ,51r[2] all ground current elements are identically structured. For each element the following characteristics are available: • ninv (iec/ xinv ); • vinv (iec/ xinv ); • linv (iec/ xinv ); • einv (iec/ xinv ); • minv (an...

Page 463

Edr-3000 im02602003e device planning parameters of the 51r ground fault protection parameter description options default menu path mode mode 51r[1]: non-directional 51r[2]: do not use, non-directional non-directional [device planning] global protection parameters of the 51r ground fault protection p...

Page 465

Edr-3000 im02602003e setting group parameters of the 51r ground fault protection parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active active [protection para / /i-prot /51r[1]] exblo fc activate (allow) or inactivate ...

Page 467

Edr-3000 im02602003e 51r ground fault protection input states name description assignment via exblo1-i module input state: external blocking1 [protection para /global prot para /i-prot /51r[1]] exblo2-i module input state: external blocking2 [protection para /global prot para /i-prot /51r[1]] exblo ...

Page 469

Edr-3000 im02602003e commissioning: ground fault protection – non-directional [ansi 51r] please test the non-directional ground overcurrent analog to the non-directional phase overcurrent protection. Www.Eaton.Com 457.

Page 471

Edr-3000 im02602003e small trip delay (about three cycles – settable) to wait for downstream devices interlocking signals. Zone interlocking trip signal only possible by absence of zone interlocking input signals. Configurable zone interlocking trip functions (protective functions serve as zone inte...

Page 473

Edr-3000 im02602003e global protection parameters of the zone interlocking in the global parameter menu for zone interlocking, two external blocking inputs (» ex block1/ex block2«), as with other protection modules, can be assigned to the input of the zone interlocking function so that the zone inte...

Page 475

Edr-3000 im02602003e parameter description setting range default menu path exblo fc activate (allow) or inactivate (disallow) blocking of the module/element. This parameter is only effective if a signal is assigned to the corresponding global protection parameter. If the signal becomes true, those m...

Page 477

Edr-3000 im02602003e www.Eaton.Com 465 zi.Out zone interlocking output logic timing started standby tripped reset standby state transfer 51p[1].Trip 51p[1].Pickup zi.Bkr blo t t 0 1 0 1 t 0 1 t 0 1 t 0 1 reset timer 10 cycles.

Page 479

Edr-3000 im02602003e zone interlocking trip logic [x2] the following overcurrent protection elements trigger phase zone-interlock trip functions: 1.5 * 51p[1]; 50p[1]; and 50p[2]. The following overcurrent protection elements trigger ground zone interlock trip functions: 51x[1]; 50x[1]; 50x[2]; 51r[...

Page 481

Edr-3000 im02602003e www.Eaton.Com 469 an d an d o r 5 0 m s t 5 0 m s t o r o r o r o r an d an d ph as e g ro un d fa ul t t yp e bo th 50 p[ 1] .P ick up 1. 5* 51 p[ 1] .P ick up 50 p[ 2] .P ick up 50 x[ 1] .P ick up 51 x[ 1] .P ick up 50 x[ 2] .P ick up 50 r[ 1] .P ic ku p 51 r[ 1] .P ic ku p 50...

Page 483

Edr-3000 im02602003e zone interlocking signals (output states) signal description active signal: active exblo signal: external blocking blo tripcmd signal: trip command blocked exblo tripcmd signal: external blocking of the trip command bkr blo signal: blocked by breaker failure phase pickup signal:...

Page 485

Edr-3000 im02602003e www.Eaton.Com 473 zone 1 j3 fp-x000 1 4 2 out in com x2 13 14 15 shield out com zone 2 16 17 18 shield in com edr-x000 zone 3 j3 fp-x000 1 4 2 out in com dt-3000 13 14 15 out in out 16 18 in com ground phase j3 fp-x000 1 4 2 out in com x2 13 14 15 shield out com 16 17 18 shield ...

Page 487

Edr-3000 im02602003e terminal marking x2 for device: edr-3000 terminal marking x2 for device: edr-4000, edr-5000, emr-4000, emr-5000, egr-4000 and egr-5000 www.Eaton.Com 475 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ro3 x?. Do not use do not use com out in com ro4 ro1 ro2 1 2 3 4 5 6 7 8 9 10 11 ...

Page 489

Edr-3000 im02602003e www.Eaton.Com 477 n am e. Tr ip c m d n am e. Tr ip p le as e r ef er to d ia gr am : b lo ck in gs ia n am e. Pi ck up p le as e r ef er to d ia gr am : tr ip b lo ck in gs 46 [1 ].. .[n ] (e le m en t i s no t d ea ct iva te d an d no a ct iv e bl oc ki ng s ig na ls ) (t rip ...

Page 491

Edr-3000 im02602003e setting group parameters of the current unbalance module parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active inactive [protection para / /unbalance-prot /46[1]] exblo fc activate (allow) or inact...

Page 493

Edr-3000 im02602003e commissioning: current unbalance module object to be tested: test of the unbalanced load protection function. Necessary means: three-phase current source with adjustable current unbalance; and timer. Procedure: check the phase sequence: ensure that the phase sequence is the same...

Page 495

Edr-3000 im02602003e testing the threshold values configure minimum » %(i2/i1)« setting (2%) and an arbitrary threshold value » threshold« (i2 fund.). For testing the threshold value, a current has to be fed to phase a which is lower than three times the adjusted threshold value » threshold« (i2 fun...

Page 497

Edr-3000 im02602003e please be aware of the meaning of the two delay timers. T load off (pickup delay): after this time expires, the load is no longer diversified. T max block (release delay): after the starting condition is fulfilled (e.G.: breaker switched on manually), the “clpu.Enabled” signal w...

Page 499

Edr-3000 im02602003e www.Eaton.Com 487 p le as e r efe r t o d ia gr am : b lo ck in gs (e le m en t i s no t d ea ct iv at ed a nd n o ac tiv e bl oc ki ng s ig na ls ) n am e = c lp u 2 c lp u .E na bl ed cl pu .I ia ib ic c lp u .I ar .R un ni ng * c lp u an d an d an d i b kr s ta te a nd i c lp...

Page 501

Edr-3000 im02602003e set parameters of the cold load pickup module parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active inactive [protection para / /clpu] exblo fc activate (allow) or inactivate (disallow) blocking of...

Page 503

Edr-3000 im02602003e commissioning of the cold load pickup module object to be tested: testing the cold load pickup module according to the configured operating mode: • i • bkr state (breaker position); • i • i necessary means: • three-phase current source (if the enable mode depends on current); • ...

Page 505

Edr-3000 im02602003e sotf - switch onto fault protection sotf in case a faulty line is energized (e.G.: when an grounding switch is in the close position), an instantaneous trip is required. The sotf module is provided to generate a permissive signal for other protection functions such as overcurren...

Page 507

Edr-3000 im02602003e device planning parameters of the switch onto fault module parameter description options default menu path mode mode do not use, use use [device planning] www.Eaton.Com 495.

Page 509

Edr-3000 im02602003e setting group parameters of the switch onto fault module parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active inactive [protection para / /sotf] exblo fc activate (allow) or inactivate (disallow) ...

Page 511

Edr-3000 im02602003e commissioning: switch onto fault [ansi 50hs] object to be tested: testing the module switch onto fault according to the configured operating mode : i bkr state (breaker position); i bkr manual close. Necessary means: three-phase current source (if the enable mode depends on curr...

Page 513

Edr-3000 im02602003e 79 - automatic reclosure ar the autoreclosure is used to minimize outages on overhead lines. The majority 1 (>60% in medium voltage and >85% in high voltage) of faults (arc flash over) on overhead lines are temporary and can be cleared by means of the autoreclosure element. De-s...

Page 515

Edr-3000 im02602003e via the pre shot (fast trip), the ar-module is able to trip the breaker ahead of the protection stage that has activated the ar-module. As a general rule, a fast trip is either issued before the first reclosure attempt or after the last permitted reclosure attempt. 1. At the beg...

Page 517

Edr-3000 im02602003e ar states the following diagram shows the state transitions between the various states of the autoreclosure function. This diagram visualizes the run time logic and timing sequence according to the state transition direction and the events which trigger the transitions. State tr...

Page 519

Edr-3000 im02602003e in general, the autoreclosure function is only active (will be initiated) when all of the following conditions are met: autoreclosure function is enabled (in ar general setting: function =active); breaker contact(s) (52a or/and 52b) is (are) installed and has (have) been program...

Page 521

Edr-3000 im02602003e 5 blocked an activated autoreclose function goes into the »b locked « state when one of the assigned blocking functions is true. The autoreclose function exits the »b locked « state if the assigned blocking signal is no longer present. Www.Eaton.Com 509.

Page 523

Edr-3000 im02602003e ar cycle (shot) 4 run (cycle) the following drawing shows the state transitions in detail inside an ar run cycle. Www.Eaton.Com 511 tr2r=out&& bkr=pos close -------------------------- ar.Successful td=out& cb=off& cb_ready=true& trip =false --------------------------------------...

Page 525

Edr-3000 im02602003e 14 t-dead while in the dead timing state » t-dead« , the pre-set dead timer for current ar shot is timing and cannot be interrupted unless there are any blocking or lockout conditions coming. After dead timer elapses, the autoreclosure issues the breaker reclosing command and go...

Page 527

Edr-3000 im02602003e timing diagrams auto reclosing timing diagram for unsuccessful 2-shot auto reclosing scheme with acceleration at pre-shot. Www.Eaton.Com 515 pre shot shot ar.Running shot 1 shot 2 ar - module states t 0 1 ready running lockout reclosing t 0 1 bkr state t 0 1 protection t 0 1 pro...

Page 529

Edr-3000 im02602003e auto reclosing states during manual breaker closing. Protection trip while manual close blocking time is timing what happens if while the timer manual close block time is timing down the protective device gets a trip signal? While the timer manual close block time is timing, any...

Page 531

Edr-3000 im02602003e zone coordination general description what does zone coordination mean? Zone coordination means that the upstream protection device is doing a virtual autoreclosure while the downstream protective device is doing a “real” autoreclosure. By means of the zone coordination, selecti...

Page 533

Edr-3000 im02602003e www.Eaton.Com 521 protective device recloser shot 1 (triggered by: i [1]) tripping curve of the fuse shot 2 (triggered by: i [2]) shot 1 (triggered by: i [1]) shot 2 (triggered by: i [2]) i t i t i t.

Page 535

Edr-3000 im02602003e global protection parameters of the module automatic reclosure parameter description setting range default menu path exblo1 external blocking of the module, if blocking is activated (allowed) within a parameter set and if the state of the assigned signal is true. 1..N, assignmen...

Page 537

Edr-3000 im02602003e setting group parameters of the module automatic reclosure parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active inactive [protection para / /ar /general settings] exblo fc activate (allow) or inac...

Page 539

Edr-3000 im02602003e parameter description setting range default menu path t-lock2ready this timer is started by the lockout reset signal, and before the timer expire the ar cannot go to any other state. 0.01 - 9999.00s 10.0s [protection para / /ar /general settings] t-run2ready examination time: if...

Page 541

Edr-3000 im02602003e parameter description setting range default menu path shot 2: initiatefc1 automatic reclosure attempt : initiate function only available if: shots = 2-6 start fct -.- [protection para / /ar /shot manager /shot 2] shot 2: initiatefc2 automatic reclosure attempt : initiate functio...

Page 543

Edr-3000 im02602003e parameter description setting range default menu path shot 5: initiatefc3 automatic reclosure attempt : initiate function only available if: shots = 5-6 start fct -.- [protection para / /ar /shot manager /shot 5] shot 5: initiatefc4 automatic reclosure attempt : initiate functio...

Page 545

Edr-3000 im02602003e module automatic reclosure signals (output states) signal description active signal: active exblo signal: external blocking standby signal: standby t-man close blo signal: ar blocked after breaker was switched on manually. This timer will be started if the breaker was switched o...

Page 547

Edr-3000 im02602003e global protection parameters of the of the ar abort functions parameter description setting range default menu path abort::1 abort the ar-cycle, if the state of the assigned signal is true. If the state of this function is true the ar will be aborted. 1..N, assignment list -.- [...

Page 549

Edr-3000 im02602003e ar start functions name description -.- no assignment 50p[1].Tripcmd signal: trip command 50p[2].Tripcmd signal: trip command 50p[3].Tripcmd signal: trip command 51p[1].Tripcmd signal: trip command 51p[2].Tripcmd signal: trip command 51p[3].Tripcmd signal: trip command 50x[1].Tr...

Page 551

Edr-3000 im02602003e www.Eaton.Com 539 1. .N , a ss ig nm en t l is t n am e. Al ar m n am e. Tr ip c m d 1. .N , a ss ig nm en t l is t n am e. Tr ip an d an d n am e. Tr ip n am e. A la rm p le as e r ef er to d ia gr am : b lo ck in gs p le as e r ef er to d ia gr am : tr ip b lo ck in gs (e le m...

Page 553

Edr-3000 im02602003e setting group parameters of the external protection module parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active inactive [protection para / /exp /exp[1]] exblo fc activate (allow) or inactivate (d...

Page 555

Edr-3000 im02602003e commissioning: external protection object to be tested: test of the external protection module. Necessary means: dependent on the application. Procedure: simulate the functionality of the external protection (pickup, trip, and blockings) by (de-)energizing the digital inputs. Su...

Page 557

Edr-3000 im02602003e locking a locking signal will be issued simultaneously with the bf -signal (trip). The locking signal is permanent. This signal has to be acknowledged at the hmi. Note on devices that offer wide frequency range measurement: the supervision scheme 50bf will be blocked as soon as ...

Page 559

Edr-3000 im02602003e • external trips : all external trips that are assigned to this breaker (within the trip manager) will start the bf module (please refer also to section „trigger signals of the breaker failure“). •in addition, the user can also select none (e.G.: if the user intends to use one o...

Page 561

Edr-3000 im02602003e 1) it is recommended to set the i by means of that it is possible to shorten the bf supervision timer and hence reduce thermal and mechanical damage of the electrical equipment in case of a breaker failure. The lower the threshold, the longer the time that is needed to detect, t...

Page 563

Edr-3000 im02602003e breaker failure protection for devices that offer voltage measurement only www.Eaton.Com 551 φ b f. T- b f s 1 r 1 1 tr ig ge r * a ll t rip s ex te rn al t rip s bk r[x ].T rip c m d * ex tt rip [x ].T rip c m d * 1. .N , 1 ..N , a ss ig nm en t li st bf .T rig ge r3 1. .N , a ...

Page 565

Edr-3000 im02602003e parameter description setting range default menu path trigger3 trigger that will start the bf trigger -.- [protection para /global prot para /supervision /bf] direct commands of the bf parameter description setting range default menu path res lockout reset lockout inactive, acti...

Page 567

Edr-3000 im02602003e bf input states name description assignment via exblo1-i module input state: external blocking1 [protection para /global prot para /supervision /bf] exblo2-i module input state: external blocking2 [protection para /global prot para /supervision /bf] trigger1-i module input: trig...

Page 569

Edr-3000 im02602003e name description logic.Le1.Gate out signal: output of the logic gate logic.Le1.Timer out signal: timer output logic.Le1.Out signal: latched output (q) logic.Le1.Out inverted signal: negated latched output (q not) logic.Le2.Gate out signal: output of the logic gate logic.Le2.Time...

Page 571

Edr-3000 im02602003e name description logic.Le19.Out signal: latched output (q) logic.Le19.Out inverted signal: negated latched output (q not) logic.Le20.Gate out signal: output of the logic gate logic.Le20.Timer out signal: timer output logic.Le20.Out signal: latched output (q) logic.Le20.Out inver...

Page 573

Edr-3000 im02602003e name description logic.Le38.Gate out signal: output of the logic gate logic.Le38.Timer out signal: timer output logic.Le38.Out signal: latched output (q) logic.Le38.Out inverted signal: negated latched output (q not) logic.Le39.Gate out signal: output of the logic gate logic.Le3...

Page 575

Edr-3000 im02602003e name description logic.Le56.Out signal: latched output (q) logic.Le56.Out inverted signal: negated latched output (q not) logic.Le57.Gate out signal: output of the logic gate logic.Le57.Timer out signal: timer output logic.Le57.Out signal: latched output (q) logic.Le57.Out inver...

Page 577

Edr-3000 im02602003e name description logic.Le75.Gate out signal: output of the logic gate logic.Le75.Timer out signal: timer output logic.Le75.Out signal: latched output (q) logic.Le75.Out inverted signal: negated latched output (q not) logic.Le76.Gate out signal: output of the logic gate logic.Le7...

Page 579

Edr-3000 im02602003e these trips will start the bf module if »external trips« have been selected as the trigger event. Name description -.- no assignment exp[1].Tripcmd signal: trip command exp[2].Tripcmd signal: trip command exp[3].Tripcmd signal: trip command exp[4].Tripcmd signal: trip command ww...

Page 581

Edr-3000 im02602003e cts - current transformer supervision cts most functions of metering, protection, and control in the relay rely on correct current measurements. It is important to make sure the ct connections and their operations are correct. The failures (including ct secondary wire broken, in...

Page 583

Edr-3000 im02602003e www.Eaton.Com 571 p le a se r e fe r to d ia gr am : b lo ck in g s ix c al cu la te d ia c ts .P ic ku p c ts (e le m en t i s no t d ea ct iv at ed a nd n o ac tiv e bl oc ki ng si gn al s) ic ib ix Σ + - kd ct s. Δi 2 an d 40 c ts . T t 0 p ha se o r g ro un d c ur re nt t ra...

Page 585

Edr-3000 im02602003e setting group parameters of the current transformer supervision parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active inactive [protection para / /supervision /cts] exblo fc activate (allow) or ina...

Page 587

Edr-3000 im02602003e commissioning: current transformer failure supervision preconditions: 1.Measurement of all three-phase currents (are applied to the measuring inputs of the device). 2.The ground current is detected via a zero sequence transformer (not in residual connection). Object to be tested...

Page 589

Edr-3000 im02602003e one breaker application examples trip circuit monitoring for one breaker: auxiliary contacts (52a and 52b) in trip circuit. Www.Eaton.Com 577 breaker 1 (bkr[1]) control voltage 1 2 3 4 5 6 7 8 pe 9 10 11 12 com1 13 14 15 16 17 18 v+ di1 com2 di2 v- x1 tc w1-52a w1-52b +dc - dc 5...

Page 591

Edr-3000 im02602003e device planning parameters of the trip circuit monitoring module parameter description options default menu path mode mode do not use, use use [device planning] www.Eaton.Com 579.

Page 593

Edr-3000 im02602003e setting group parameters of the trip circuit monitoring module parameter description setting range default menu path function permanent activation or deactivation of module/element. Inactive, active inactive [protection para / /supervision /tcm] exblo fc activate (allow) or inac...

Page 595

Edr-3000 im02602003e commissioning: trip circuit monitoring for breakers for breakers that trip by means of little energy (e.G.: via an optocoupler), it has to be ensured that the current applied by the digital inputs will not cause false tripping of the breaker. Object to be tested: test of the tri...

Page 597

Edr-3000 im02602003e the measuring unit continuously checks the measured data by comparing received data with data from a second channel sampled in parallel. The auxiliary voltage is monitored continuously. If the voltage of one of the different supply circuits falls below a certain threshold, a res...

Page 599

Edr-3000 im02602003e programmable logic available elements (equations): logic general description the protective device includes programmable logic equations for programming inputs, outputs, blocking of protective functions, and custom logic functions in the relay. The logic provides control of the ...

Page 601

Edr-3000 im02602003e detailed overview – overall logic diagram. Www.Eaton.Com 589 φ a n d o r n a n d n o r t- o n d el ay t- o ff d e la y g at e o u t t im e r o u t o ut o ut in ve rt e d d el ay t im er 1. .N , a ss ig nm en t l is t le [x ].I n 1 ac tiv e in ac tiv e in ve rti ng 1 x o r 1. .N ...

Page 603

Edr-3000 im02602003e cascading logical outputs the device will evaluate output states of the logic equations starting from “logic equation 1” up to the logic equation with the highest number. This evaluation cycle will be continuously repeated. Cascading logic equations in an ascending sequence. Cas...

Page 605

Edr-3000 im02602003e programmable logic at the panel warning improper use of logic equations might result in personal injury or damage the electrical equipment. Do not use logic equations unless the user can ensure the safe functionality. How to configure a logic equation? Within the device planning...

Page 607

Edr-3000 im02602003e selection list for logic input signals name description -.- no assignment prot.Active signal: active prot.Available signal: protection is available. Prot.Pickup signal: general pickup prot.Trip signal: general trip bkr.Si singlecontactind signal: the position of the switchgear i...

Page 609

Edr-3000 im02602003e name description 50r[1].Tripcmd signal: trip command 50r[2].Pickup signal: pickup ix or ir 50r[2].Trip signal: trip 50r[2].Tripcmd signal: trip command 51r[1].Pickup signal: pickup ix or ir 51r[1].Trip signal: trip 51r[1].Tripcmd signal: trip command 51r[2].Pickup signal: pickup...

Page 611

Edr-3000 im02602003e name description wired inputs.Toca m2-i state of the module input: main 2 breaker connected wired inputs.43/10 m2-i state of the module input: main 2 breaker selected to trip wired inputs.52a t-i state of the module input: tie breaker closed wired inputs.52b t-i state of the mod...

Page 613

Edr-3000 im02602003e name description iec61850.Virtinp8 signal: virtual input (iec61850 ggio ind) iec61850.Virtinp9 signal: virtual input (iec61850 ggio ind) iec61850.Virtinp10 signal: virtual input (iec61850 ggio ind) iec61850.Virtinp11 signal: virtual input (iec61850 ggio ind) iec61850.Virtinp12 s...

Page 615

Edr-3000 im02602003e name description logic.Le13.Timer out signal: timer output logic.Le13.Out signal: latched output (q) logic.Le13.Out inverted signal: negated latched output (q not) logic.Le14.Gate out signal: output of the logic gate logic.Le14.Timer out signal: timer output logic.Le14.Out signa...

Page 617

Edr-3000 im02602003e name description logic.Le31.Out inverted signal: negated latched output (q not) logic.Le32.Gate out signal: output of the logic gate logic.Le32.Timer out signal: timer output logic.Le32.Out signal: latched output (q) logic.Le32.Out inverted signal: negated latched output (q not)...

Page 619

Edr-3000 im02602003e name description logic.Le50.Timer out signal: timer output logic.Le50.Out signal: latched output (q) logic.Le50.Out inverted signal: negated latched output (q not) logic.Le51.Gate out signal: output of the logic gate logic.Le51.Timer out signal: timer output logic.Le51.Out signa...

Page 621

Edr-3000 im02602003e name description logic.Le68.Out inverted signal: negated latched output (q not) logic.Le69.Gate out signal: output of the logic gate logic.Le69.Timer out signal: timer output logic.Le69.Out signal: latched output (q) logic.Le69.Out inverted signal: negated latched output (q not)...

Page 623

Edr-3000 im02602003e global protection parameter of the programmable logic parameter description setting range default menu path le1.Gate logic gate and, or, nand, nor and [logic /le 1] le1.In1 assignment of the input signal 1..N, logiclist -.- [logic /le 1] le1.Inverting1 inverting the input signal...

Page 625

Edr-3000 im02602003e programmable logic inputs name description assignment via le1.Gate in1-i state of the module input: assignment of the input signal [logic /le 1] le1.Gate in2-i state of the module input: assignment of the input signal [logic /le 1] le1.Gate in3-i state of the module input: assig...

Page 627

Edr-3000 im02602003e commissioning before starting work on an open switchboard, it is required that the switchboard is de-energized and the following five safety regulations have been met. Safety precautions: disconnect the power supply; secure against reconnection; verify that the equipment is de-e...

Page 629

Edr-3000 im02602003e decommissioning – removing the plug from the relay dismounting the relay will lead to a loss of the protection functionality. Ensure that there is a back-up protection. If you are not aware of the consequences of decommissioning the device – stop! Do not start. Inform scada befo...

Page 631

Edr-3000 im02602003e maintenance mode principle – general use the maintenance mode can be used to reduce arc flash levels. Refer to std. Nfpa70e. Do not attempt to install or perform maintenance on equipment while it is energized. Severe personal injury or death can result from contact with energize...

Page 633