1. DL manuals
  2. Eaton
  3. UPS
  4. Powerware BladeUPS Bar
  5. Installation Manual

Eaton Powerware BladeUPS Bar Installation Manual

Manual is about: Eaton Electrical BladeUPS Bar Powerware Installation Guide

Summary of Powerware BladeUPS Bar

  • Page 1

    Powerware bladeups bar installation guide ® ®.

  • Page 2

    Special symbols the following are examples of symbols used on the ups or accessories to alert you to important information: risk of electric shock - observe the warning associated with the risk of electric shock symbol. Caution: refer to operator’s manual - refer to your operator’s manual for additi...

  • Page 3

    Eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 i table of contents 1 introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety warnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    Table of contents eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 ii.

  • Page 5

    Eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 1 chapter 1 introduction up to six of eaton’s powerware ® bladeups ® uninterruptible power systems (upss) can be installed in an industry standard rack outfitted with a bladeups bar 60 for interconnecting the cabinets’ wiring. F...

  • Page 6

    Introduction eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 2 safety warnings important safety instructions save these instructions this manual contains important instructions that you should follow during installation and maintenance of the bladeups bar 60. Please read all ...

  • Page 7

    Introduction eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 3 wichtige sicherheitsanweisungen aufbewaren dieses handbuch enthält wichtige hinweise, welche sie bei der installation und wartung des bladeups bar 60 beachten sollten. Bitte lesen sie alle anweisungen des handbuch...

  • Page 8

    Introduction eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 4 instrucciones de seguridad importantes guarde estas instrucciones este manual contiene instrucciones importantes que debe seguir durante la instalación y el funcionamiento del bladeups bar 60. Por favor, lea todas...

  • Page 9

    Eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 5 chapter 2 installation this section explains: s equipment inspection s bladeups bar 60 setup and installation inspecting the equipment if any equipment has been damaged during shipment, keep the shipping cartons and packing ma...

  • Page 10

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 6 checking the package contents verify that the following items are included: s bladeups bar 60 a six-socket bar with (1) attached terminal block assembly, (1) attached base bracket, and (3) attached mounting bracke...

  • Page 11

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 7 installation to install the bladeups bar 60: 1. Remove the access cover and terminal block housing from the wireway housing (see figure 2). Retain the wireway terminal block housing, wireway access cover, and scre...

  • Page 12

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 8 4. Install an m6 hex nut onto each of the three wireway studs to secure the wireway to the rear of the rack. Install the first stud in the fourth hole location from the bottom. Do not tighten the nuts. Figure 4 sh...

  • Page 13

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 9 9. Place the ferrite assembly on the floor of the wireway and secure with the supplied tie wrap. Loop the tie wrap through both attachment sites on the wireway floor and through the ferrite assembly. See figure 4....

  • Page 14

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 10 note verify that the bar is secure as shown in figure 4. The sheetmetal at the base of the bar should be below the tab on the wireway floor. 12. Secure the bar to the wireway with three m6 × 12 hex bolts. Install...

  • Page 15

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 11 14. Secure the base bracket to the rack with three m6 × 12 hex bolts. Install the bolts from the rear of the rack. Use a large screwdriver or crowbar to lift the bar in place to align the holes in the base bracke...

  • Page 16

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 12 16. Install two m4 × 8 pan-head screws into the tab on the wireway floor, securing the base of the bar to the wireway. See figure 7. Torque the screws to 1.7 ± 0.2 nm (15 ± 2 lb in). Rear of rack wireway floor ta...

  • Page 17

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 13 17. Using two m6 × 12 hex bolts, secure the left side of the wireway terminal block housing to the rack. See figure 8. Torque the bolts to 5.1 ± 0.8 nm (45 ± 7 lb in). 18. Using nine m4 × 8 pan-head screws, secur...

  • Page 18

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 14 19. Using five m4 × 8 pan-head screws, install the wireway access cover. See figure 9. Torque the screws to 1.7 ± 0.2 nm (15 ± 2 lb in). M4 ×8 pan-head screws (5 places) wireway access cover figure 9. Wireway acc...

  • Page 19

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 15 21. Using four m5 × 16 hex bolts and four m5 cage nuts, secure the front cover mounting panel to the front of the rack. Verify that the bent edge of the panel is at the top. See figure 11. Install the lower bolts...

  • Page 20

    Installation eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 16 22. Snap the two front covers into place, as shown in figure 12. Front covers (2 pieces) figure 12. Front cover installation.

  • Page 21

    Eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 17 chapter 3 specifications this section provides the following specifications: table 1. Bladeups bar 60 dimensions (wxdxh) 14.0 ×11.3×183.8 cm (5.5”×4.4”×72.4”) depth of wireway 90.1 cm (35.5”), excluding front covers weight ba...

  • Page 22

    Specifications eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 18.

  • Page 23

    Eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 19 chapter 4 service and support if you have any questions or problems with the bladeups bar, call your local distributor or the help desk at one of the following telephone numbers and ask for a ups technical representative. Uni...

  • Page 24

    Service and support eaton powerware ® bladeups ® bar installation guide s 164201723 rev p01 20

  • Page 28

    *164201723p01* 164201723 p01.