1. DL manuals
  2. Eaton
  3. DC Drives
  4. PowerXL DE1 series
  5. Manual

Eaton PowerXL DE1 series Manual

Other manuals for PowerXL DE1 series: Quick Start Manual, Manual
Manual is about: Variable speed starter Variable Speed Starter VSS / Configuration module

Summary of PowerXL DE1 series

  • Page 1

    Manual powerxl ™ de1… – variable speed starter variable speed starter vss dxe-ext-set – configuration module 11/16 mn040011en.

  • Page 2

    De1… variable speed starterall proprietary names and product designations are brand names or trademarks registered to the relevant title holders. Break-down service please call your local representative: http://eaton.Com/moeller/aftersales or hotline after sales service: +49 (0) 180 5 223822 (de, en...

  • Page 3: Danger!

    I before commencing the installation • disconnect the power supply of the device. • ensure that devices cannot be accidentally retriggered. • verify isolation from the supply. • ground and short-circuit. • cover or enclose neighbouring units that are live. • follow the engineering instructions (il) ...

  • Page 4

    Ii.

  • Page 5: Content

    De1… variable speed starter 11/16 mn040011en www.Eaton.Com 1 content 0 about this manual ..................................................................... 5 0.1 target group................................................................................. 5 0.2 list of revisions ....................

  • Page 6

    2 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 2.4 emc measures ............................................................................ 31 2.5 motor selection ........................................................................... 33 2.5.1 parallel connection of motors ..........

  • Page 7

    De1… variable speed starter 11/16 mn040011en www.Eaton.Com 3 6 parameter ................................................................................... 79 6.1 dx-key-led keypad..................................................................... 80 6.1.1 key combinations...........................

  • Page 8

    4 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 10 fault messages .......................................................................... 153 10.1 acknowledge fault message (reset) ........................................... 154 10.2 fault log ...........................................

  • Page 9: 0 About This Manual

    0 about this manual 0.1 target group de1… variable speed starter 11/16 mn040011en www.Eaton.Com 5 0 about this manual this manual contains specific information that will enable you to select a de1... Variable speed starter, connect it, and use its parameters to configure it as required for your spec...

  • Page 10

    0 about this manual 0.4 writing conventions 6 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 0.4 writing conventions symbols with the following meaning are used in this manual: ▶ indicates instructions to be followed. 0.4.1 hazard warnings of material damages 0.4.2 hazard warnings of per...

  • Page 11

    0 about this manual 0.5 abbreviations de1… variable speed starter 11/16 mn040011en www.Eaton.Com 7 0.5 abbreviations the following abbreviations are used in this manual: table 1: acronyms and abbreviations abbreviation meaning ds default settings emc electromagnetic compatibility fe functional earth...

  • Page 12

    0 about this manual 0.6 mains supply voltages 8 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 0.6 mains supply voltages the rated operating voltages stated in the following table are based on the nominal values for networks with an earthed star point. In ring networks (as found in europ...

  • Page 13: 1 De1... Series

    1 de1... Series 1.1 introduction de1… variable speed starter 11/16 mn040011en www.Eaton.Com 9 1 de1... Series 1.1 introduction ease of use and high reliability make powerxl™ de1... Variable speed starters the ideal choice for general applications involving three-phase motors. These variable speed st...

  • Page 14

    1 de1... Series 1.1 introduction 10 de1… variable speed starter 11/16 mn040011en www.Eaton.Com figure 1: de1... Housing versions (left: 45 mm, right: 90 mm) and optional dxe-ext-set configuration module l1/l l2/n l3 u v w 0 v +10 v 1 2 3 4 13 14 l1/l l2/n l3 u v w 0 v +10 v 1 2 3 4 13 14.

  • Page 15

    1 de1... Series 1.2 system overview de1… variable speed starter 11/16 mn040011en www.Eaton.Com 11 1.2 system overview figure 2: system overview (example) a de1…-... Variable speed starters b dx-ln… mains choke, dx-lm3-… motor choke, dx-emc… external radio interference suppression filter c dxe-ext-se...

  • Page 16

    1 de1... Series 1.3 checking the delivery 12 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 1.3 checking the delivery the de1... Series variable speed starter are carefully packed and prepared for shipment. The devices should be shipped only in their original packaging with suitable tran...

  • Page 17

    1 de1... Series 1.4 rated operational data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 13 1.4 rated operational data the device-specific rated operational data for the de1... Variable speed starter is listed on the nameplate on the right side of the device. Figure 4: nameplate locatio...

  • Page 18

    1 de1... Series 1.4 rated operational data 14 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 1.4.1 rating data on the nameplate the inscription of the nameplates has the following meaning (example): inscription meaning de1-343d6fn-n20n part no.: de1 = de1 variable speed starter 3 = three...

  • Page 19

    1 de1... Series 1.4 rated operational data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 15 1.4.2 designation the catalog number selection/part no. For de1 variable speed starters is subdivided into three groups series – power section – model – (versions) the following figure shows it i...

  • Page 20

    1 de1... Series 1.5 designation 16 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 1.5 designation the following drawing shows an example of the physical configuration of a de1... Variable speed starter with a size of 90 mm. Figure 8: designation (width: 90 mm) a fixing holes (screw faste...

  • Page 21

    1 de1... Series 1.6 voltage categories de1… variable speed starter 11/16 mn040011en www.Eaton.Com 17 1.6 voltage categories de1... Variable speed starters are subdivided into two voltage categories: • de1…- 12 … • single-phase mains connection 230 v • u ln = 1~, 200 - 240 v ± 10 %, 50/60 hz • i e : ...

  • Page 22

    1 de1... Series 1.7 selection criteria 18 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 1.7 selection criteria de1... Variable speed starters should be selected based on the supply voltage provided by the mains (u ln ) and the rated operational current of the motor being used. The motor...

  • Page 23

    1 de1... Series 1.8 proper use de1… variable speed starter 11/16 mn040011en www.Eaton.Com 19 1.8 proper use the de1... Variable speed starters are not domestic appliances. They are designed only for industrial use as system components. The de1... Variable speed starters are electrical devices for co...

  • Page 24

    1 de1... Series 1.9 maintenance and inspection 20 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 1.9 maintenance and inspection de1... Variable speed starters are maintenance-free, provided that the gen- eral rating data, as well as the technical data for the specific models in use, is o...

  • Page 25

    1 de1... Series 1.11 charging the internal dc link capacitors de1… variable speed starter 11/16 mn040011en www.Eaton.Com 21 1.11 charging the internal dc link capacitors the de1-12… variable speed starter’s dc link features electrolytic capaci- tors. After prolonged storage or non-operation periods ...

  • Page 26

    1 de1... Series 1.12 service and warranty 22 de1… variable speed starter 11/16 mn040011en www.Eaton.Com.

  • Page 27: 2 Engineering

    2 engineering de1… variable speed starter 11/16 mn040011en www.Eaton.Com 23 2 engineering this chapter contains instructions that must be followed when determining which device to use with which rated motor output, as well as when selecting protection devices and switchgear, selecting cables, cable ...

  • Page 28

    2 engineering 2.1 introduction 24 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 2.1 introduction this section describes the most important characteristics of the power circuit for a power drive system (pds) that need to be taken into account when planning and configuring your applicatio...

  • Page 29

    2 engineering 2.2 electrical power network de1… variable speed starter 11/16 mn040011en www.Eaton.Com 25 2.2 electrical power network 2.2.1 mains connection and configuration de1... Variable speed starters can be connected to and run on all neutral point-grounded ac supply systems (tn-s, tn-c, tt gr...

  • Page 30

    2 engineering 2.2 electrical power network 26 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 2.2.2 mains voltage and frequency the de1... Variable speed starter’s wide tolerance range makes it possible to use the device with european (u ln = 230 v/400 v, 50 hz) and american (u ln = 240 v...

  • Page 31

    2 engineering 2.2 electrical power network de1… variable speed starter 11/16 mn040011en www.Eaton.Com 27 2.2.4 reactive power compensation ￫ in the ac supply systems with non-choked reactive current compensation devices, current oscillations, antiresonances and undefinable circumstances can occur. I...

  • Page 32

    2 engineering 2.3 safety and switching 28 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 2.3 safety and switching 2.3.1 disconnecting device in the european union, this disconnecting device must be one of the following devices in order to comply with european directives as per standard e...

  • Page 33

    2 engineering 2.3 safety and switching de1… variable speed starter 11/16 mn040011en www.Eaton.Com 29 if there are leakage currents greater than 3.5 ma, a reinforced earthing (pe) must be connected, as required by standard en 61800-5-1. The cable cross- section must be at least 10 mm 2 , or the earth...

  • Page 34

    2 engineering 2.3 safety and switching 30 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 2.3.4 mains contactors using a mains contactor makes it possible to switch the variable speed starter’s supply voltage on and off under normal operating conditions and to disconnect it in the event o...

  • Page 35

    2 engineering 2.4 emc measures de1… variable speed starter 11/16 mn040011en www.Eaton.Com 31 2.4 emc measures when designing drives systems with variable speed (pds), the necessary electromagnetic compatibility (emc) measures should already be taken into account during the planning and configuration...

  • Page 36

    2 engineering 2.4 emc measures 32 de1… variable speed starter 11/16 mn040011en www.Eaton.Com figure 17: cable routing figure 18: separate routing a power cable: mains voltage, motor connection b control and signal lines, fieldbus connections ￫ do not route the control and signal cables ② in the same...

  • Page 37

    2 engineering 2.5 motor selection de1… variable speed starter 11/16 mn040011en www.Eaton.Com 33 2.5 motor selection 2.5.1 parallel connection of motors de1... Variable speed starters can be used to run several motors in parallel. Connecting several motors in parallel will reduce the resistance at th...

  • Page 38

    2 engineering 2.5 motor selection 34 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 2.5.2 circuit types with three-phase motors the three-phase motor’s stator winding can be connected in a star or delta circuit as per the rated operational data on the rating plate. Figure 19: example of ...

  • Page 39: 3 Installation

    3 installation 3.1 introduction de1… variable speed starter 11/16 mn040011en www.Eaton.Com 35 3 installation 3.1 introduction this chapter provides a description of the mounting and the electrical connection for the variable speed starter de1... 3.2 mounting the installation instructions described i...

  • Page 40

    3 installation 3.2 mounting 36 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.2.1 mounting position de1...-121d4… and de1...-122d3… variable speed starters (devices without an internal fan) must be installed in a vertical position. The maximum permis- sible inclination for them is 5°. ...

  • Page 41

    3 installation 3.2 mounting de1… variable speed starter 11/16 mn040011en www.Eaton.Com 37 there must be a clearance of at least 15 mm in front of the device. Figure 24: minimum clearance ￫ devices with strong magnetic fields (e.G., chokes and transformers) should not be installed in the striking dis...

  • Page 42

    3 installation 3.2 mounting 38 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.2.3 fixing all de1... Variable speed starter sizes can be mounted: • with screws, • on a mounting rail, 3.2.3.1 fixing with screws figure 25: screw fixing ￫ the appendix lists the dimensions, weights, and req...

  • Page 43

    3 installation 3.2 mounting de1… variable speed starter 11/16 mn040011en www.Eaton.Com 39 3.2.3.2 fixing on a mounting rail as an alternative to screw fixing, de1... Variable speed starters can also be mounted on an iec/en 60715-compliant mounting rail. Figure 26: mounting rail conforming with iec/e...

  • Page 44

    3 installation 3.3 electrical installation 40 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3 electrical installation caution carry out wiring work only after the variable speed starter has been correctly mounted and secured. Danger electric shock hazard - risk of injuries! Before car...

  • Page 45

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 41 3.3.1 insulation test the variable speed starters of the de1... Series are tested, delivered and require no additional testing. If insulation testing is required in the power circuit of the pds, ...

  • Page 46

    3 installation 3.3 electrical installation 42 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.2 connection to power section the mains-side connection to the power section must be established using the connection terminals: • l1/l, l2/n, pe for the single-phase supply voltage powering ...

  • Page 47

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 43 figure 30: sealed-off connection terminals (example: de1-12…nn-…) the connection terminals sealed off in figure 30 (l3 and ) do not serve any function. 3.3.2.1 power terminal designations table 4...

  • Page 48

    3 installation 3.3 electrical installation 44 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.2.2 connection examples table 5: power section connection examples connection terminals description mains connec tion de1…-12…fn-… with single-phase supply voltage (200 v/240 v) with built-in...

  • Page 49

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 45 3.3.2.3 terminal capacities and stripping lengths figure 31: stripping lengths in the power section table 6: stripping lengths, conductor cross-sections, tightening torque 3.3.3 earthing every de...

  • Page 50

    3 installation 3.3 electrical installation 46 de1… variable speed starter 11/16 mn040011en www.Eaton.Com figure 32: inserting the pe cable behind the emc jumper (clamping action from the back towards the front) 3.3.4 emc jumper there are two de1... Variable speed starter versions: • de1...-… f n-…: ...

  • Page 51

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 47 figure 34: removing the emc jumpers on the mains and motor sides notice do not insert or remove the emc jumpers if the de1... Variable speed starter is connected to the electrical mains. ￫ the tw...

  • Page 52

    3 installation 3.3 electrical installation 48 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.5 three-phase commoning link dil12m-xdsb0/… three-phase commoning links, which provide protection against contact and are short-circuit-proof, can be used to connect de1...-34… variable speed...

  • Page 53

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 49 figure 36: pe connection for the individual variable speed starters (example) three-phase commoning link can be used with the following maximum number of de1... Variable speed starter sizes dilm1...

  • Page 54

    3 installation 3.3 electrical installation 50 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.6 motor connection the connection between the de1... Variable speed starter and the motor should be as short as possible. The motor connection cable should be screened in order for the instal...

  • Page 55

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 51 the following figure shows an example illustrating the layout for a four-core, screened motor cable (recommended configuration). Figure 39: four-core screened motor supply cable a cu shield braid...

  • Page 56

    3 installation 3.3 electrical installation 52 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.7 installations meeting ul ® requirements de1... Variable speed starters fully meet ul requirements, provided that the following conditions are fully met: • in the case of de1...-12… devices,...

  • Page 57

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 53 3.3.8 connection to control section the following connection terminals are used to make the connection to the control section: • 0 v, +10 v: control voltage output • 1, 2, 3, 4: digital and analo...

  • Page 58

    3 installation 3.3 electrical installation 54 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.8.2 connecting the control cables the control cables are connected without screening. In the case of environments with extensive em interference, as well as in the case of control cables conn...

  • Page 59

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 55 3.3.8.3 terminal capacities and stripping lengths the terminal capacities and stripping lengths are listed in the following table. Table 8: connection cables at the control terminals m3 mm 2 mm 2...

  • Page 60

    3 installation 3.3 electrical installation 56 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.8.4 connection examples control section table 9: connection examples with the mode 0 default setting (p-15) connection terminals description soft start function motor start carried out with c...

  • Page 61

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 57 3.3.8.5 analog input control terminal 4 (ai1/di4) can be used either with analog or digital input signals. If you are using the device’s default settings, control terminal 4 will be configured as...

  • Page 62

    3 installation 3.3 electrical installation 58 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.8.6 digital inputs as digital inputs (di1, di2, di3), control terminals 1, 2, and 3 are identical in terms of their function and how they work. Control terminal 4 is set up as analog input ai...

  • Page 63

    3 installation 3.3 electrical installation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 59 table 11: connection examples for the digital inputs (mode 0) connection terminals description default settings the digital inputs (di1 - di3) and the setpoint value (ai1) are driven with the int...

  • Page 64

    3 installation 3.3 electrical installation 60 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.3.8.7 relay contact (run) control terminals 13 and 14 are connected to the de1... Variable speed starter’s internal potential-free relay contact (n/o). • this contact will close when there is a...

  • Page 65

    3 installation 3.4 rj 45 interface de1… variable speed starter 11/16 mn040011en www.Eaton.Com 61 3.4 rj 45 interface the rj45 interface in the front can be used to connect the device directly to communication and fieldbus connection modules ( ￫ figure 46, page 62). Figure 45: rj 45 interface the int...

  • Page 66: →

    3 installation 3.4 rj 45 interface 62 de1… variable speed starter 11/16 mn040011en www.Eaton.Com figure 46: system overview for the de1 variable speed starter’s rj45 interface 6 3 4 5 2 1 pwr usb rxd serial sw txd drivesconnect parametereditor drivecontrol/monitor functionblockeditor scope/datalogge...

  • Page 67

    3 installation 3.5 led indicators de1… variable speed starter 11/16 mn040011en www.Eaton.Com 63 3.5 led indicators there are three light-emitting diodes (leds) used to show the de1... Variable speed starter’s operating states. Figure 47: leds with fault codes (printed on housing) the run , status , ...

  • Page 68

    3 installation 3.5 led indicators 64 de1… variable speed starter 11/16 mn040011en www.Eaton.Com table 12: "fault code" led fault messages fault code flashing frequency: 2 hz (followed by a 2-second pause) meaning 1 pulse - overload 1 x thermal motor overload 2 pulses - external fault 2 x external fa...

  • Page 69

    3 installation 3.6 block diagrams de1… variable speed starter 11/16 mn040011en www.Eaton.Com 65 3.6 block diagrams the following block diagrams show all of the de1 variable speed starter’s connection terminals and their functions when the device is used with its default settings. 3.6.1 de1…-12…fn-… ...

  • Page 70

    3 installation 3.6 block diagrams 66 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 3.6.3 de1…-34…fn-… figure 50: de1-34…fn-… block diagram variable speed starter with three-phase mains supply voltage and internal radio interference suppression filter 3.6.4 de1…-34…nn-… figure 51: de1-34...

  • Page 71: 4 Operation

    4 operation 4.1 checklist for commissioning de1… variable speed starter 11/16 mn040011en www.Eaton.Com 67 4 operation 4.1 checklist for commissioning before putting the variable speed starter into operation, make sure to check the following checklist items: table 13: checklist for commissioning no. ...

  • Page 72

    4 operation 4.2 hazard warnings for operation 68 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 4.2 hazard warnings for operation please observe the following notes. Danger commissioning is only to be completed by qualified technicians. Danger hazardous voltage! The safety instructions o...

  • Page 73

    4 operation 4.2 hazard warnings for operation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 69 notice inching operation using the mains contactor is not permitted. Contactors and switchgear (repair and maintenance switches) on the motor side must not be opened while the motor is in oper...

  • Page 74

    4 operation 4.3 commissioning with default settings 70 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 4.3 commissioning with default settings following is a simplified connection example for operating the device with its default settings: ▶ for simple commissioning with the preset defaul...

  • Page 75

    5 dxe-ext-set configuration module 5.1 dxe-ext-set designation de1… variable speed starter 11/16 mn040011en www.Eaton.Com 71 5 dxe-ext-set configuration module figure 52: dxe-ext-set configuration module the dxe-ext-set configuration module can be used to easily change the default settings for a de1...

  • Page 76

    5 dxe-ext-set configuration module 5.2 plugging the module into / removing it from a de1... Variable speed starter 72 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 5.2 plugging the module into / removing it from a de1... Variable speed starter the dxe-ext-set configuration module is des...

  • Page 77

    5 dxe-ext-set configuration module 5.3 description and use de1… variable speed starter 11/16 mn040011en www.Eaton.Com 73 5.3 description and use in order to be able to adjust the potentiometer and rotary switch settings on the dxe-ext-set configuration module, you will need a flat-blade screwdriver ...

  • Page 78

    5 dxe-ext-set configuration module 5.3 description and use 74 de1… variable speed starter 11/16 mn040011en www.Eaton.Com the following table goes over the use and functions of the operator control and indication elements on the dxe-ext-set configuration module when it is plugged in and the de1... Va...

  • Page 79

    5 dxe-ext-set configuration module 5.3 description and use de1… variable speed starter 11/16 mn040011en www.Eaton.Com 75 p-09 = rated motor frequency ramp selector switch 0.1 s / 1 s / 3 s / 5 s / 10 s / 15 s / 30 s / 60 s / 120 s / 180 s the 10-setting ramp selector switch can be used to select a s...

  • Page 80

    5 dxe-ext-set configuration module 5.3 description and use 76 de1… variable speed starter 11/16 mn040011en www.Eaton.Com mode selector switch the 10-setting mode selector switch can be used to configure the de1... Variable speed starter’s control terminals. The mode selector switch can only be used ...

  • Page 81

    5 dxe-ext-set configuration module 5.3 description and use de1… variable speed starter 11/16 mn040011en www.Eaton.Com 77 mode 3 one operating direction (fwd) frequency reference value via potentiometer (0 - +10 v) or via fixed frequency (ff1 = 20 hz). An external fault message (extflt) can be connec...

  • Page 82

    5 dxe-ext-set configuration module 5.3 description and use 78 de1… variable speed starter 11/16 mn040011en www.Eaton.Com mode 8 machine control (1) ena enable signal the operating direction will be determined based on the dir (low = fwd / high = rev) control command. The frequency reference value is...

  • Page 83: 6 Parameter

    6 parameter de1… variable speed starter 11/16 mn040011en www.Eaton.Com 79 6 parameter following is a description of the de1... Variable speed starter’s parameters and functions. These parameters can be accessed using the device’s front rj45 interface and require optionally available interface conver...

  • Page 84

    6 parameter 6.1 dx-key-led keypad 80 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.1 dx-key-led keypad the optional dx-key-led keypad (version 1.2 or higher) for de1... Variable speed starters can be used to easily configure a device’s parameters. It comes with a 3 m-long connection c...

  • Page 85

    6 parameter 6.1 dx-key-led keypad de1… variable speed starter 11/16 mn040011en www.Eaton.Com 81 table 16: dx-key-led keypad description operating unit element explanation 7-segment led display six-digit display with decimal points start button motor start with the pre-selected operating direction (f...

  • Page 86

    6 parameter 6.1 dx-key-led keypad 82 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 7-segment led display the display unit is a 7-segment led display with five decimal points. The led segments are red. Figure 58: 7-segment led display when the required supply voltage is applied (connecti...

  • Page 87

    6 parameter 6.1 dx-key-led keypad de1… variable speed starter 11/16 mn040011en www.Eaton.Com 83 6.1.2 parameter structure when using a dx-key-led keypad, the de1... Variable speed starter’s parameters will be accessed in a closed ring configuration, figuratively speaking. To start selecting paramete...

  • Page 88

    6 parameter 6.1 dx-key-led keypad 84 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.1.3 setting parameters table 18 below provides an example that illustrates how to operate the external dx-key-led keypad in order to select and adjust the p-02 (f-min) parameter when a minimum speed (fr...

  • Page 89

    6 parameter 6.2 drivesconnect de1… variable speed starter 11/16 mn040011en www.Eaton.Com 85 6.2 drivesconnect figure 60: main drivesconnect components on start screen the drivesconnect parameter configuration software can be used with a computer to quickly configure, operate, and diagnose a de1... V...

  • Page 90

    6 parameter 6.3 modbus rtu and canopen 86 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.3 modbus rtu and canopen modbus rtu can be used to cyclically configure the parameters of and control the de1... Variable speed starter through a centrally controlled bus system. To connect the de1...

  • Page 91

    6 parameter 6.4 smartwire-dt de1… variable speed starter 11/16 mn040011en www.Eaton.Com 87 6.4 smartwire-dt the centrally controlled smartwire-dt wiring system can be used to cyclically configure the parameters of and control the de1... Variable speed starter. The smartwire-dt system requires a spec...

  • Page 92

    6 parameter 6.5 parameter description 88 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.5 parameter description the parameter descriptions found below use a series of abbreviations and acronyms. These abbreviations and acronyms are defined in the following table: 6.5.1 acceleration and...

  • Page 93

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 89 figure 62: acceleration and deceleration time p-05 133 run rw stop mode 0/1 1 stop mode used to define how the de1... Variable speed starter will behave if the enable signal (fwd/ rev) is switched off...

  • Page 94

    6 parameter 6.5 parameter description 90 de1… variable speed starter 11/16 mn040011en www.Eaton.Com the following formulas can be used to calculate acceleration time t 1 and deceleration time t 2 (relative to the motor’s rated frequency (p-09)) for a max- imum output frequency p-01: if there is a gi...

  • Page 95

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 91 6.5.2 motor data figure 63: motor parameters from ratings plate when selecting the rating data, take the dependency of the circuit types on the mains voltage into account: • 230 v in p-07 ￫ delta circ...

  • Page 96

    6 parameter 6.5 parameter description 92 de1… variable speed starter 11/16 mn040011en www.Eaton.Com table 20: parameter p-07, p-08, p-09, p-10 pnu modbus id access right name value ds description run, stop ro/rw p-07 135 stop rw motor rated voltage 50 - 500 v 220 v, 230 v, 380 v, 400 v, 460 v rated ...

  • Page 97

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 93 6.5.3 motor protection 6.5.3.1 overload protection (i x t) in order to protect the motor against thermal overload, a thermal motor model with an i x t characteristic will be computed in the de1... Var...

  • Page 98

    6 parameter 6.5 parameter description 94 de1… variable speed starter 11/16 mn040011en www.Eaton.Com table 21: parameters p-08 and p-33 6.5.3.2 thermistor protection measuring the temperature in the motor’s stator windings is the most effective way to protect the motor against thermal overload. De1.....

  • Page 99

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 95 • fault code led: 2 pulses – external fault • dx-key-led: e-trip once the motor winding cools down (= the thermistors cool down), the fault message can be reset, provided the resistance has fallen bel...

  • Page 100

    6 parameter 6.5 parameter description 96 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.5.4 v/f characteristic curve the inverter in the de1... Variable speed starter works using sinusoidal pulse width modulation (pwm). With it, the igbts are driven with two v/hz control-based control ...

  • Page 101

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 97 p-08 1) 136 stop rw rated motor current (10 - 100 %) x i e i e rated operational current of the motor by default, the value in p-08 will be iden- tical to the de1... Variable speed starter’s rated ope...

  • Page 102

    6 parameter 6.5 parameter description 98 de1… variable speed starter 11/16 mn040011en www.Eaton.Com v/f control mode volts per hertz control (v/hz characteristic) refers to the de1... Variable speed starter control method in which motor voltage is regulated so that it is maintained at a specific rat...

  • Page 103

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 99 energy optimizer if p-06 = 1, the de1... Variable speed starter’s energy optimizer will be enabled, in which case the output voltage will be adjusted automatically based on the load. In partial load s...

  • Page 104

    6 parameter 6.5 parameter description 100 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.5.5 dc braking when using dc braking, de1... Variable speed starters apply a dc voltage to the stator windings of the connected three-phase motor. This makes it possi- ble to brake motors that are ...

  • Page 105

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 101 6.5.6 control terminal configuration parameter p-15 can be used to configure the function of control terminals 1 through 4. When parameter p-15 is used, parameter p-12 can be used to configure access...

  • Page 106

    6 parameter 6.5 parameter description 102 de1… variable speed starter 11/16 mn040011en www.Eaton.Com the acronyms and abbreviations used for the control terminals’ function are defined below: table 25: function of the control terminals ￫ the optional dxe-ext-set configuration module can only be used...

  • Page 107

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 103 table 26: parameters for configuring the control terminals pnu modbus id access right name value ds description run, stop ro/rw p-12 140 run rw processdata- access 0 - 13 0 process data access contro...

  • Page 108

    6 parameter 6.5 parameter description 104 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.5.6.1 control terminal and keypad when the device is used together with an optional external keypad (dxe- key-led), the start and stop buttons can be used to start and stop the drive, and the speed...

  • Page 109

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 105 in both settings (p-12 = 1, p-12 = 2), the control terminals can be configured with p-15 as follows: table 27: configuration with external keypad 6.5.6.2 control signal terminals and modbus rtu p-12 ...

  • Page 110

    6 parameter 6.5 parameter description 106 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.5.6.3 smartwire-dt when the device is used together with smartwire-dt, the control terminals can be configured as shown below by using parameter p-15. P-12 = 9 (swd control + swd setpoint value) p-...

  • Page 111

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 107 p-12 = 10 (control), setpoint value via control terminals table 29: configuration with smartwire-dt and p-12 (= 10) p-12 = 12 (swd control + swd setpoint value), will switch automatically to control ...

  • Page 112

    6 parameter 6.5 parameter description 108 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 6.5.6.4 digital reference value reset mode table 31: parameter p-24 when p-12 = 0 (control commands via terminals) and p-15 = 4, 5, or 6, the frequency reference value can be set digitally (up/down)....

  • Page 113

    6 parameter 6.5 parameter description de1… variable speed starter 11/16 mn040011en www.Eaton.Com 109 control terminals’ start start and stop commands. However, it will still be possible to use the two arrow keys on the keypad in order to digitally set the frequency reference value. 6.5.6.5 analog in...

  • Page 114

    6 parameter 6.5 parameter description 110 de1… variable speed starter 11/16 mn040011en www.Eaton.Com figure 71: scaled reference value input inverting analog input ai1 parameter p-18 can be used to configure analog input ai1 for applications with an inverted reference voltage (f-max at 0 v, f-min at...

  • Page 115

    6 parameter 6.6 parameter lock de1… variable speed starter 11/16 mn040011en www.Eaton.Com 111 6.6 parameter lock the de1... Variable speed starter’s parameters can be protected from misuse. This function can be used to ensure that only authorized people will be able to make changes to the parameters...

  • Page 116

    6 parameter 6.7 default settings 112 de1… variable speed starter 11/16 mn040011en www.Eaton.Com table 33: parameter lock 6.7 default settings table 34: default settings (p-37) pnu modbus id access right name value ds description run, stop ro/rw p-14 142 run rw password 0 - 65535 0 access code passwo...

  • Page 117

    6 parameter 6.8 displaying operational data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 113 6.8 displaying operational data the variable speed starter’s operational data can be displayed using the extended parameter set (p-14 = 101, ￫ page 83): • external dx-key-led keypad: press the ...

  • Page 118

    6 parameter 6.8 displaying operational data 114 de1… variable speed starter 11/16 mn040011en www.Eaton.Com pnu id display value description p00-04 11 0000 no digital input (di1, di2, di3, di4) is actuated 1000 control signal on terminal 1 active (di1) 0100 control signal on terminal 2 active (di2) 0...

  • Page 119: 7 M

    7 modbus rtu und canopen bus systems 7.1 modbus rtu de1… variable speed starter 11/16 mn040011en www.Eaton.Com 115 7 m odbus rtu und canopen bus systems 7.1 modbus rtu 7.2 canopen ￫ for detailed information on modbus rtu bus system in connection with de1… variable speed starters, please refer to the...

  • Page 120

    7 modbus rtu und canopen bus systems 7.2 canopen 116 de1… variable speed starter 11/16 mn040011en www.Eaton.Com.

  • Page 121: 8 Technical Data

    8 technical data 8.1 features de1… variable speed starter 11/16 mn040011en www.Eaton.Com 117 8 technical data the following tables show the performance characteristics for the various de1... Variable speed starter models together with the motor power that are compatible with them. 8.1 features ￫ the...

  • Page 122

    8 technical data 8.2 general rating data 118 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 8.2 general rating data symbol unit value standards specification for general requirements: iec/en 61800-2 emc requirements: iec/en 61800-3; safety requirements: iec/en 61800-5-1 certifications an...

  • Page 123

    8 technical data 8.3 rating data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 119 8.3 rating data 8.3.1 de1…-12… (single-phase mains connection) sym- bol unit de1…- 121d4… de1…- 122d3… de1…- 122d7… de1…- 124d3… de1…- 127d0… de1…- 129d6… mains connection rated opera- tional voltage u e ...

  • Page 124

    8 technical data 8.3 rating data 120 de1… variable speed starter 11/16 mn040011en www.Eaton.Com heat dissipation (idle, standby) p v w 3.44 3.44 3.44 3.44 3.44 4.66 heat dissipation (speed/torque) 100/100 p v w 17 20 27 32 59 105 90/100 p v w 16 18 25 31 57 102 100/50 p v w 13 14 15 16 33 49 90/100 ...

  • Page 125

    8 technical data 8.3 rating data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 121 control section relay contact s (run signal) voltage, maximum u v 250 ac/30 dc 250 ac/30 dc 250 ac/30 dc 250 ac/30 dc 250 ac/30 dc 250 ac/30 dc load current, maximum i a 6 ac-1/5 dc-1 6 ac-1/5 dc-1 6 ac-1...

  • Page 126

    8 technical data 8.3 rating data 122 de1… variable speed starter 11/16 mn040011en www.Eaton.Com terminal capacities, clampable power section solid or stranded a mm² 1 - 6 1 - 6 1 - 6 1 - 6 1 - 6 1 - 6 flexible with ferrule a mm² 1 - 6 1 - 6 1 - 6 1 - 6 1 - 6 1 - 6 solid or stranded a awg 18 - 6 18 -...

  • Page 127

    8 technical data 8.3 rating data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 123 8.3.2 de1…-34… (three-phase mains connection) symbol unit de1…-341d3… de1…-342d1… de1…-343d6… de1…-345d0… mains connection rated operational voltage u e v 380/400/480, 3-phase 380/400/480, 3-phase 380/400...

  • Page 128

    8 technical data 8.3 rating data 124 de1… variable speed starter 11/16 mn040011en www.Eaton.Com motor feeder motor power, assigned at 400 v, 50 hz p kw 0.37 0.75 1.5 2.2 at 440 - 480 v, 60 hz p hp 1/2 1 2 3 apparent power at rated value at 400 v s kva 0.90 1.45 2.49 3.46 at 480 v s kva 1.08 1.75 2.9...

  • Page 129

    8 technical data 8.3 rating data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 125 terminal capacities, clampable power section solid or stranded a mm² 1 - 6 1 - 6 1 - 6 1 - 6 flexible with ferrule a mm² 1 - 6 1 - 6 1 - 6 1 - 6 solid or stranded a awg 18 - 6 18 - 6 18 - 6 18 - 6 strip l...

  • Page 130

    8 technical data 8.3 rating data 126 de1… variable speed starter 11/16 mn040011en www.Eaton.Com symbol unit de1…-346d6… de1…-348d5… de1…-34011… de1…-34016… mains connection rated operational voltage u e v 380/400/480, 3-phase mains voltage u ln v 380 - 480 ±10 % (342 - 528) mains frequency f hz 50/6...

  • Page 131

    8 technical data 8.3 rating data de1… variable speed starter 11/16 mn040011en www.Eaton.Com 127 motor feeder motor power assigned at 400 v, 50 hz p kw 3 4 5.5 7.5 at 440 - 480 v, 60 hz p hp 3 5 7.5 10 apparent power at rated value at 400 v s kva 4.57 5.89 7.62 11.09 at 480 v s kva 5.49 7.07 9.15 13....

  • Page 132

    8 technical data 8.3 rating data 128 de1… variable speed starter 11/16 mn040011en www.Eaton.Com terminal capacities, clampable power section solid or stranded a mm² 1 - 6 1 - 6 1 - 6 1 - 6 flexible with ferrule a mm² 1 - 6 1 - 6 1 - 6 1 - 6 solid or stranded a awg 18 - 6 18 - 6 18 - 6 18 - 6 strip l...

  • Page 133

    8 technical data 8.4 dimensions de1… variable speed starter 11/16 mn040011en www.Eaton.Com 129 8.4 dimensions figure 73: dimensions table 35: dimensions l1/l l2/n l3 u v w 0 v +10 v 1 2 3 4 13 14 ⌀1 ⌀2 ⌀ c c1 a a1 b b4 b3 b1 b2 size a a1 b b1 b2 c c1 ⌀ 1 ⌀ 2 mm (in) mm (in) mm (in) mm (in) mm (in) m...

  • Page 134

    8 technical data 8.4 dimensions 130 de1… variable speed starter 11/16 mn040011en www.Eaton.Com.

  • Page 135: 9 Accessory Devices

    9 accessory devices 9.1 dx-key-led external keypad de1… variable speed starter 11/16 mn040011en www.Eaton.Com 131 9 accessory devices 9.1 dx-key-led external keypad figure 74: dx-key-led with rj45 cable (3 m) the dx-key-led keypad can be used to control de1... Variable speed start- ers externally, c...

  • Page 136

    9 accessory devices 9.1 dx-key-led external keypad 132 de1… variable speed starter 11/16 mn040011en www.Eaton.Com a maximum of two keypads can be connected to a powerxl network with a maximum of 63 modules (op bus). Figure 76: example: powerxl network (op bus) with two keypads if using two keypads, ...

  • Page 137

    9 accessory devices 9.1 dx-key-led external keypad de1… variable speed starter 11/16 mn040011en www.Eaton.Com 133 setting the port address the keypad’s port address can be set by pressing the ok + stop + ▼ key combination at the same time. Display: port-1 use the arrow keys to select the port addres...

  • Page 138

    9 accessory devices 9.2 dx-com-stick communications stick 134 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 9.2 dx-com-stick communications stick the dx-com-stick communication stick can be used to easily transfer parameters by: • copying all parameters to devices belonging to the same ...

  • Page 139

    9 accessory devices 9.2 dx-com-stick communications stick de1… variable speed starter 11/16 mn040011en www.Eaton.Com 135 the arrow buttons on the dx-com-stick communication stick can be used to control the direction in which parameters will be transferred: the parameters will be copied from the dx-c...

  • Page 140

    9 accessory devices 9.3 smartwire-dt dx-net-swd3 136 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 9.3 smartwire-dt dx-net-swd3 figure 79: dx-net-swd3 the dx-net-swd3 option module can be used to connect a de1... Variable speed starter to smartwire-dt. Together with a smartwire-dt gatew...

  • Page 141

    9 accessory devices 9.4 dx-cbl-pc1m5 computer cable de1… variable speed starter 11/16 mn040011en www.Eaton.Com 137 9.4 dx-cbl-pc1m5 computer cable figure 81: dx-cbl-pc-1m5 the dx-cbl-pc-1m5 computer connection cable can be used to establish wired, galvanically isolated communications between a de1.....

  • Page 142

    9 accessory devices 9.5 dx-com-pckit interface card 138 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 9.5 dx-com-pckit interface card the dx-com-pckit interface can be used to establish wired, galvanically isolated communications between a master controller (host computer) and several (...

  • Page 143

    9 accessory devices 9.5 dx-com-pckit interface card de1… variable speed starter 11/16 mn040011en www.Eaton.Com 139 dx-com-pckit has several ports and interfaces with different configura- tions. The following come as standard for direct connection to a computer: • an approximately 80 cm-long cable wi...

  • Page 144

    9 accessory devices 9.6 splitter dx-spl-rj45-2sl1pl 140 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 9.6 splitter dx-spl-rj45-2sl1pl the splitter is specifically designed to connect powerxl drive controllers using rj45 connectors. The rj45 ports are connected in parallel and make it po...

  • Page 145

    9 accessory devices 9.7 cable and safety devices de1… variable speed starter 11/16 mn040011en www.Eaton.Com 141 9.7 cable and safety devices the mains cables and motor cables must be sized as required by local stan- dards and by the load currents that will be involved. The rated operational currents...

  • Page 146

    9 accessory devices 9.7 cable and safety devices 142 de1… variable speed starter 11/16 mn040011en www.Eaton.Com table 37: fusing and assigned cross-sectional areas the cable cross-sectional areas that can be properly clamped in place, as well as the stripping lengths, are provided in the technical d...

  • Page 147

    9 accessory devices 9.7 cable and safety devices de1… variable speed starter 11/16 mn040011en www.Eaton.Com 143 table 38: protective devices that should be used for de1...-12… devices table 39: protective devices that should be used for de1...-34… devices device type input current 1) i ln fuses (iec...

  • Page 148

    9 accessory devices 9.8 dil…mains contactors 144 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 9.8 dil…mains contactors table 40: assigned mains contactors ￫ the mains contactors listed here are based on the de1... Variable speed starter’s rated input-side mains current i ln without a m...

  • Page 149

    9 accessory devices 9.9 dx-ln… mains chokes de1… variable speed starter 11/16 mn040011en www.Eaton.Com 145 9.9 dx-ln… mains chokes the de1... Variable speed starter’s rated input currents serve as the basis used to determine which mains chokes should be used. T figure 87: main chokes dex-ln… ￫ if th...

  • Page 150

    9 accessory devices 9.9 dx-ln… mains chokes 146 de1… variable speed starter 11/16 mn040011en www.Eaton.Com table 41: assigned mains chokes device type rated current input current 1) mains voltage (50/60 hz) main choke i e i ln u lnmax part no. I e a a v a de1…-121d4… 1.4 3.6 240 +10 % dx-ln1-006 6 d...

  • Page 151

    9 accessory devices 9.10 external emc filter de1… variable speed starter 11/16 mn040011en www.Eaton.Com 147 9.10 external emc filter dx-emc… radio interference suppression filters make it possible to use de1... Variable speed starters with longer motor cables, as well as with other emc interference ...

  • Page 152

    9 accessory devices 9.10 external emc filter 148 de1… variable speed starter 11/16 mn040011en www.Eaton.Com figure 90: modifying the prefabricated connection cables the spade lug terminals must be removed directly at the point where they are connected [1]. The connection cables should not be shorten...

  • Page 153

    9 accessory devices 9.10 external emc filter de1… variable speed starter 11/16 mn040011en www.Eaton.Com 149 de1…-345d0… dx-emc34-019-fs3 dx-emc34-019-fs3-l 50 100 100 de1…-346d6… de1…-348d5… de1…-34011… de1…-34016… 1) reduced motor cable length in category c1 when combining de1...-34…nn… and reduced...

  • Page 154

    9 accessory devices 9.11 motor choke dx-lm3… 150 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 9.11 motor choke dx-lm3… it is recommended to use a motor choke if using long cable lengths and/or connecting several motors in parallel. The motor choke needs to be placed at the de1... Varia...

  • Page 155

    9 accessory devices 9.11 motor choke dx-lm3… de1… variable speed starter 11/16 mn040011en www.Eaton.Com 151 table 43: motor chokes that should be used device type motor choke that should be used voltage class part no. Rated opera- tional current i e 200 - 240 v 380 - 480 v a de1…-121d4… de1…-341d3… ...

  • Page 156

    9 accessory devices 9.11 motor choke dx-lm3… 152 de1… variable speed starter 11/16 mn040011en www.Eaton.Com.

  • Page 157: 10 Fault Messages

    10 fault messages de1… variable speed starter 11/16 mn040011en www.Eaton.Com 153 10 fault messages de1... Variable speed starters feature several internal monitoring functions. If they detect a state deviating from a normal operating state, they will show a fault message: • operation will stop • the...

  • Page 158

    10 fault messages 10.1 acknowledge fault message (reset) 154 de1… variable speed starter 11/16 mn040011en www.Eaton.Com if the de1... Variable speed starter has an internal communication fault (cpu fault), the green run led will turn off and the status and fault code leds will both show a continuous...

  • Page 159

    10 fault messages 10.2 fault log de1… variable speed starter 11/16 mn040011en www.Eaton.Com 155 the following example shows how to access the fault memory with the dx-key-led keypad: view description operating state stop press the ok button and hold it down for two seconds. The most recently accesse...

  • Page 160

    10 fault messages 10.3 fault list 156 de1… variable speed starter 11/16 mn040011en www.Eaton.Com 10.3 fault list the following table lists the de1... Variable speed starter’s fault messages, as well as possible causes and fixes: • fault code led (2 hz + 2 s) = number of flashing pulses plus a 2-seco...

  • Page 161

    10 fault messages 10.3 fault list de1… variable speed starter 11/16 mn040011en www.Eaton.Com 157 6 x 05 ps-trf power section fault • fault message from the power section’s output. ￫ check the connection to the motor (short-circuit, earth fault). ￫ disconnect the cable from terminals u, v, w. ￫ if th...

  • Page 162

    10 fault messages 10.3 fault list 158 de1… variable speed starter 11/16 mn040011en www.Eaton.Com.

  • Page 163: 11 List Of Parameters

    11 list of parameters de1… variable speed starter 11/16 mn040011en www.Eaton.Com 159 11 list of parameters following is an overview of all the parameters in de1... Variable speed starters, including a brief description. The abbreviations and acronyms used in the overview are defined below: table 46:...

  • Page 164

    11 list of parameters 160 de1… variable speed starter 11/16 mn040011en www.Eaton.Com p-05 133 run rw stop mode 0; 1 1 stop mode used to define how the de1... Variable speed starter will behave if the enable signal (fwd/rev) is switched off: 1 : the drive will decelerate with the time set in p- 04 al...

  • Page 165

    11 list of parameters de1… variable speed starter 11/16 mn040011en www.Eaton.Com 161 p-10 138 stop rw motor nom speed 0/200 - 15000 rpm (18000 rpm) 0 rated speed of the motor display value: 0 : output frequency in hz ≧ 200 : rpm. All frequency-based parameter values will be converted and shown in rp...

  • Page 166

    11 list of parameters 162 de1… variable speed starter 11/16 mn040011en www.Eaton.Com p-12 140 run rw processdataaccess 0 - 13 0 process data access (control level) used to select the control and signal paths that will be used. Regardless of the control level selected, the enable signal at di1 (fwd) ...

  • Page 167

    11 list of parameters de1… variable speed starter 11/16 mn040011en www.Eaton.Com 163 extended parameter range (default access code: p-14 = 101) p-15 143 stop rw di configuration selection 0 - 9 0 function of the control terminals when p12 = 0, control terminals di1 to di4 can be configured with the ...

  • Page 168

    11 list of parameters 164 de1… variable speed starter 11/16 mn040011en www.Eaton.Com p-19 147 stop rw di3 logic 0/1 0 digital input di3, logic di3 logic when assigned the extflt (external fault) function in p-15 (= 1, 3, 5, 7, 9): 0 : high = ok, low = extflt 1 : low = ok, high = extflt led fault mes...

  • Page 169

    11 list of parameters de1… variable speed starter 11/16 mn040011en www.Eaton.Com 165 p-29 1) 157 stop rw switching frequency 4 - 32 khz 10 - 20 khz 16 khz switching frequency switching frequency (audible pulse frequency) of igbts in power section de1-12… : 4/8/12/16/24/32 khz de1-34… : 10/12/14/16/1...

  • Page 170

    11 list of parameters 166 de1… variable speed starter 11/16 mn040011en www.Eaton.Com p-34 162 run rw pdp address 1 - 63 1 pdp address unique address of de1 variable speed starter on a communication network – p-35 163 run rw modbus baud rate 0 - 4 4 modbus baud rate 0 = 960 bit/s 1 = 19.2 kbit/s 2 = ...

  • Page 171

    11 list of parameters de1… variable speed starter 11/16 mn040011en www.Eaton.Com 167 p-41 169 run rw parameteraccess 0; 1 0 parameter access 0 : all parameters can be changed from any source (smartwire-dt, drivesconnect, external keypad). 1 : all parameters are locked and can only be changed via sma...

  • Page 172

    11 list of parameters 168 de1… variable speed starter 11/16 mn040011en www.Eaton.Com display parameters, monitor extended parameter range (default access code: p-14 = 101) table 47: display parameters, monitor pnu access right name value description ro/rw p00-01 ro analog input 1 0.0 - 100 % analog ...

  • Page 173

    11 list of parameters de1… variable speed starter 11/16 mn040011en www.Eaton.Com 169 p00-14 ro actual switching frequency 16 khz switching frequency, active instantaneous value of switching frequency. If p-32 = 0 (temperature management enabled for heat sink), this value may be lower than the value ...

  • Page 174

    11 list of parameters 170 de1… variable speed starter 11/16 mn040011en www.Eaton.Com.

  • Page 175: Index

    De1 variable speed starter 11/16 mn040011en www.Eaton.Com 171 index a abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ac supply systems . . . . . . . . . . . . . . . . . . . . . . . . 25 acceleration time . . . . . . . . . . . . . . . . . . . . . . . . . 88 accessories . ...

  • Page 176

    172 de1 variable speed starter 11/16 mn040011en www.Eaton.Com i i x t characteristic . . . . . . . . . . . . . . . . . . . . . . . . . 93 inching operation . . . . . . . . . . . . . . . . . . . . . . . . . . 69 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 installatio...

  • Page 177

    De1 variable speed starter 11/16 mn040011en www.Eaton.Com 173 t technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 terminal capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 55 testing the motor cable insulation . . . . . . . . . . . 41 thermistor protection . . . . ...