Eaton XV400 5.7" Operating Instructions Manual - Device Description

Manual is about: MICRO PANEL

Summary of XV400 5.7"

  • Page 1

    Operating instructions 12/2014 mn04802009z-en replaces m000746 xv400 5.7"/8.4" micro panel.

  • Page 2

    Imprint 2 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com manufacturer support original instructions the german version of this document is the original instructions. Translations of the original instructions all non-german editions of this document are translations of the original ...

  • Page 3: Contents

    Contents micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 3 contents 1 general....................................................................................................................... 7 1.1 purpose of these operating instructions............................................

  • Page 4

    Contents 4 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.3.7 usb host .................................................................................................................... 36 5.3.8 can...................................................................................

  • Page 5

    Contents micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5 9.8 applicable standards and regulations ......................................................................... 76 9.9 ambient conditions.......................................................................................

  • Page 6

    Contents 6 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com.

  • Page 7: General

    1 general 1.1 purpose of these operating instructions micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 7 1 general 1.1 purpose of these operating instructions these operating instructions contain the information required for the correct and safe use of the micro panels xv400 5.7"/8.4...

  • Page 8

    1 general 1.3 additional documentation 8 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com.

  • Page 9: Device Description

    2 device description 2.1 device names micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 9 2 device description 2.1 device names xv400 5.7"/8.4" and mc2 5.7" are two different names of equivalent products. 2.2 function micro panels xv400 5.7"/8.4"; mc2 5.7" can be used as hmi devices o...

  • Page 10

    2 device description 2.4 device versions 10 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com abb. 1 5.7" device with resistive touch and standard front abb. 2 5.7" device with infra-red touch and standard front abb. 3 5.7" device with infra-red touch and 4-hole front abb. 4 5.7" devi...

  • Page 11

    2 device description 2.5 package contents micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 11 2.5 package contents the accessories supplied with the micro panels xv400 5.7"/8.4"; mc2 5.7" depend on the device version. 2.5.1 package contents for devices with standard front tab. 2 pack...

  • Page 12

    2 device description 2.6 accessories 12 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 2.5.3 package contents for devices with stainless steel front tab. 4 package contents for devices with stainless steel front 2.6 accessories different accessories are available. Use only original...

  • Page 13: Safety Regulations

    3 safety regulations 3.1 general micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 13 3 safety regulations 3.1 general hazards may still occur even though the device meets the current state of the art and complies with all recognized safety requirements. The device must only be instal...

  • Page 14

    3 safety regulations 3.2 meaning of symbols 14 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 3.2 meaning of symbols the following symbols are used in this document according to the hazard level described: the danger symbol used and the text indicate the actual danger and the relat...

  • Page 15

    3 safety regulations 3.3 mandatory requirements, personnel micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 15 3.3 mandatory requirements, personnel 3.3.1 work safety all applicable work safety regulations (in-house and national) must be observed. 3.3.2 qualification of personnel the...

  • Page 16

    3 safety regulations 3.3 mandatory requirements, personnel 16 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 3.3.6 requirements for proper operation the following points must be observed so that the device meets the contractual requirements: only qualified personnel may work with t...

  • Page 17

    3 safety regulations 3.4 device related hazards micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 17 3.4 device related hazards danger explosion hazard death, serious injury or material damage may occur if an electrical plug connection is removed in a potentially explosive atmosphere ...

  • Page 18

    3 safety regulations 3.4 device related hazards 18 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com caution non-isolated interfaces the device may be damaged due to potential differences. The gnd terminals of all bus stations must be connected. Caution sensitive resistive touch surfa...

  • Page 19

    3 safety regulations 3.4 device related hazards micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 19 caution cleaning the device damage to the device due to the use of pointed or sharp objects or by liquids. Do not use any pointed or sharp objects (e.G. Knife) for cleaning. Do not use...

  • Page 20

    3 safety regulations 3.4 device related hazards 20 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com.

  • Page 21

    4 operating and indication elements 4.1 operating and indication elements on the front micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 21 4 operating and indication elements 4.1 operating and indication elements on the front the device has the following operating and indication elem...

  • Page 22

    4 operating and indication elements 4.2 operating elements on the service side 22 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 4.2 operating elements on the service side the device has the following operating elements on the service side: tab. 6 operating elements on the service ...

  • Page 23

    4 operating and indication elements 4.3 indication elements on the service side micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 23 4.3 indication elements on the service side the device has the following indication elements on the service side: tab. 7 indication elements on the serv...

  • Page 24

    4 operating and indication elements 4.3 indication elements on the service side 24 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com.

  • Page 25: Installation

    5 installation 5.1 safety regulations micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 25 5 installation 5.1 safety regulations read chapter 3 safety regulations, 13 before installing and commissioning the de- vice. This contains important information for your personal safety..

  • Page 26

    5 installation 5.2 requirements for the place of installation 26 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.2 requirements for the place of installation approvals: the device must only be used in locations that are approved for the device. See the markings on the nameplate an...

  • Page 27

    5 installation 5.2 requirements for the place of installation micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 27 special specifications apply to the mounting surfaces of devices with a stainless steel front which have to ensure protection to ip69k (required for cleaning with high-pr...

  • Page 28

    5 installation 5.3 interfaces 28 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.3 interfaces warning potential equalization currents large equalization currents between the protective ground systems of different de- vices may cause operational malfunctions due to signal interfere...

  • Page 29

    5 installation 5.3 interfaces micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 29 5.3.1 overview of interfaces connector side: service side: tab. 8 overview of interfaces abb. 10 connector side of the device abb. 11 service side of the device interface interface description a etherne...

  • Page 30

    5 installation 5.3 interfaces 30 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.3.2 preparation of cables with d-sub connector the preparation of bus cables is an essential factor in ensuring reliable operation and electromagnetic compatibility (emc). Wiring requirements the cabl...

  • Page 31

    5 installation 5.3 interfaces micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 31 abb. 13 cable prepared with d-sub connector a cable with cable sheath b heat shrinkable tubing or rubber grommet c cable clamp d shield braid e d-sub connector f mounting screw unc the emc values stated...

  • Page 32

    5 installation 5.3 interfaces 32 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.3.3 power supply the device is provided with an internal fuse and is protected against polarity reversal. The functional earthing terminal is connected to both the housing and the 0 v terminal. The de...

  • Page 33

    5 installation 5.3 interfaces micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 33 5.3.4 rs232 (system port) the rs232 interface is not electrically isolated. The gnd pin is directly connected to the housing potential. Tab. 11 pin assignment of the rs232 interface wiring shielded cabl...

  • Page 34

    5 installation 5.3 interfaces 34 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com when preparing the cables, ensure that there is a low-resistance connection between the cable shield and the connector casing ( chapter 5.3.2, 30)..

  • Page 35

    5 installation 5.3 interfaces micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 35 5.3.5 ethernet for the approval in accordance with the standard ul 60950, consideration must be given to the condi- tions for use in an end-product (according to underwriters labaratories inc. (ul)): in...

  • Page 36

    5 installation 5.3 interfaces 36 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.3.6 usb device the usb device interface supports usb 1.1. Cable only use shielded usb standard cable. Maximum cable length: 5 m. 5.3.7 usb host the usb host interface supports usb 2.0. Cable only use ...

  • Page 37

    5 installation 5.3 interfaces micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 37 5.3.8 can the can interface is electrically isolated. Tab. 14 pin assignment of can interface in accordance with cia wiring shielded twisted pair cables must be used. Tab. 15 cable specifications the ma...

  • Page 38

    5 installation 5.3 interfaces 38 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com tab. 16 relationship of cable length / baud rate can bus topology a bus segment can connect up to 32 bus stations. Several bus segments can be linked via repeaters (bidirectional amplifiers). Refer to t...

  • Page 39

    5 installation 5.4 mounting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 39 5.4 mounting 1 check the device for damage in transit. 2 if necessary, fit the required communication module in the device. See chapter 5.4.1 fitting the communication module in the device, 40. 3 mount th...

  • Page 40

    5 installation 5.4 mounting 40 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.4.1 fitting the communication module in the device the device is provided with a slot for a communication module. Optional communication modules enable the device to be connected to automation devices (...

  • Page 41

    5 installation 5.4 mounting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 41 procedure: 1 configure the communication module as stated in the relevant module description. 2 loosen the knurled screws on the slot cover. 3 remove the slot cover. 4 fit the communication module in the ...

  • Page 42

    5 installation 5.4 mounting 42 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.4.2 mounting a device with standard front 1 select the mounting position of the device as described in chapter 5.2.2 requirements for the mounting position, 26. 2 prepare a mounting cutout for the devic...

  • Page 43

    5 installation 5.4 mounting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 43 4 fit the supplied threaded pins in the retaining brackets beforehand. 5 fit the device from the front into the mounting cutout. 6 clip on the retaining brackets in the recesses provided for them on the d...

  • Page 44

    5 installation 5.4 mounting 44 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com devices which must be mounted in accordance with ip65 or used in potentially explosive atmo- spheres: top and bottom of the device: one retaining bracket at each of the fixing positions (left, right and i...

  • Page 45

    5 installation 5.4 mounting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 45 5.4.3 mounting a device with 4-hole front 1 select the mounting position of the device as described in chapter 5.2.2 requirements for the mounting position, 26. 2 prepare a mounting cutout for the device ...

  • Page 46

    5 installation 5.4 mounting 46 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 3.4 fit the front seal with the adhesive side face down onto the rear of the front plate and press it down. 4 fit the device from the front into the mounting cutout. 5 fasten the device so that the front ...

  • Page 47

    5 installation 5.4 mounting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 47 5.4.4 mounting a device with stainless steel front (standard mounting and mounting to ip65) 1 select the mounting position of the device as described in chapter 5.2.2 requirements for the mounting positio...

  • Page 48

    5 installation 5.4 mounting 48 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 3.1 fit the seal in the groove on the rear of the device front plate. 3.2 use a small screwdriver to push the securing tabs of the seal into the groove. The securing tabs must not protrude over the edge o...

  • Page 49

    5 installation 5.4 mounting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 49 standard mounting: top and bottom of the device: fit one retaining bracket each at the left and right fixing position devices which must be mounted in accordance with ip65 or used in potentially explosive...

  • Page 50

    5 installation 5.4 mounting 50 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 5.4.5 mounting a device with stainless steel front (mounting to ip69k) 1 select the mounting position of the device as described in chapter 5.2.2 requirements for the mounting position, 26. 2 prepare a mo...

  • Page 51

    5 installation 5.4 mounting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 51 3.1 fit the seal in the groove on the rear of the device front plate. 3.2 use a small screwdriver to push the securing tabs of the seal into the groove. The securing tabs must not protrude over the edge o...

  • Page 52

    5 installation 5.4 mounting 52 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com left and right on the device: one retaining bracket each at the central fixing position 7 if the device front plate is not flush mounted, fit a suitable protection in order to achieve the required sealing...

  • Page 53: Operation

    6 operation 6.1 safety regulations micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 53 6 operation 6.1 safety regulations read chapter 3 safety regulations, 13 before working with the device. This contains important information for your personal safety. Caution sensitive resistive to...

  • Page 54

    6 operation 6.2 starting the device 54 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 6.2 starting the device 1 insert the cf card with the operating system: 1.1 remove the cf slot cover (a). 1.2 insert the cf card into cf slot (b). 1.3 fit the cf slot cover (a). 2 energize the dev...

  • Page 55

    6 operation 6.2 starting the device micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 55 3 if the device does not boot up and/or if an error message appears while starting (booting) the device, see chapter 7.4 troubleshooting, 62. 4 complete the following steps after initial commissio...

  • Page 56

    6 operation 6.3 switching off the device 56 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 6.3 switching off the device 1 de-energize the device. Caution data loss during a write operation, the cf card may lose data or may be destroyed if it is re- moved or if there is a power fail...

  • Page 57: Maintenance and Service

    7 maintenance and service 7.1 safety regulations micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 57 7 maintenance and service 7.1 safety regulations read chapter 3 safety regulations, 13 before working with the device. This contains important information for your personal safety..

  • Page 58

    7 maintenance and service 7.2 maintenance 58 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 7.2 maintenance devices with resistive touch are maintenance-free. However, the following work may be necessary: cleaning of the resistive touch if contaminated. Recalibration of the resisti...

  • Page 59

    7 maintenance and service 7.2 maintenance micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 59 7.2.3 cleaning the infra-red touch the infra-red frame must be cleaned regularly. The infra-red channels may be interrupted if the infra-red frame is severely contaminated. In extreme cases,...

  • Page 60

    7 maintenance and service 7.2 maintenance 60 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com tab. 18 information in cleaning instructions 7.2.4 recalibrating the infra-red touch devices with infra-red touch do not have to be recalibrated. 7.2.5 battery the integrated battery cannot ...

  • Page 61

    7 maintenance and service 7.3 service micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 61 7.3 service 7.3.1 repairs the device must only be opened by the manufacturer or by an authorized repair center. Contact your local supplier or eaton technical support for repairs. Only the origi...

  • Page 62

    7 maintenance and service 7.4 troubleshooting 62 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 7.4 troubleshooting fault and possible cause corrective action device does not start (boot). Power supply interface does not have any power. Check the power supply cable. While the devic...

  • Page 63

    7 maintenance and service 7.4 troubleshooting micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 63 tab. 19 troubleshooting touch is deactivated. Start (boot) the device. Activate touch ( document «mn05010007z-en system description windows ce»). Led «touch error» permanently lit and/or...

  • Page 64

    7 maintenance and service 7.4 troubleshooting 64 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com.

  • Page 65

    8 storage, transport and disposal 8.1 safety regulations micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 65 8 storage, transport and disposal 8.1 safety regulations 8.2 storage the ambient conditions for storage must be fulfilled. See chapter 9.9 ambient conditions, 77. 8.3 transpor...

  • Page 66

    8 storage, transport and disposal 8.4 disposal 66 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 8.4 disposal devices that are no longer used must be properly disposed of in accordance with the applicable national regulations or returned to the manufacturer or sales office. Materia...

  • Page 67: Technical Data

    9 technical data 9.1 dimensions and weights micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 67 9 technical data 9.1 dimensions and weights 9.1.1 5.7" devices with standard or stainless steel front tab. 22 dimensions and weights of the 5.7" devices with standard or stainless steel fr...

  • Page 68

    9 technical data 9.1 dimensions and weights 68 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 9.1.2 5.7" devices with 4-hole front tab. 23 dimensions and weights of the 5.7" devices with 4-hole front abb. 48 mechanical dimensions of the 5.7" devices with 4-hole front in mm property...

  • Page 69

    9 technical data 9.1 dimensions and weights micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 69 9.1.3 8.4" devices tab. 24 dimensions and weights of the 8.4" devices abb. 49 mechanical dimensions of the 8.4" devices in mm property xv400 8.4" height 208 mm width 275 mm depth 95 mm thi...

  • Page 70

    9 technical data 9.2 display 70 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 9.2 display 9.2.1 5.7" devices xv-432-57; mc2-432-57 and xv-442-57; mc2-442-57 tab. 25 display of the 5.7" devices xv-432-57; mc2-432-57 and xv-442-57; mc2-442-57 1) devices with infra-red touch and stan...

  • Page 71

    9 technical data 9.2 display micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 71 9.2.2 5.7" devices xv-450-57 and xv-460-57 tab. 26 display of the 5.7" devices xv-450-57 and xv-460-57 9.2.3 8.4" devices tab. 27 display of the 8.4" devices property xv-450-57 and xv-460-57 type tft-lcd...

  • Page 72

    9 technical data 9.3 touch sensor 72 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 9.3 touch sensor 9.3.1 devices with resistive touch tab. 28 touch sensor of the devices with resistive touch 9.3.2 devices with infra-red touch tab. 29 touch sensor of the devices with infra-red tou...

  • Page 73

    9 technical data 9.5 interfaces micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 73 9.5 interfaces tab. 31 interfaces property xv400 5.7"/8.4"; mc2 5.7" ethernet 100base-tx / 10base-t system port rs232, not electrically isolated usb host usb 2.0 (1.5 / 12 mbit/s), not electrically is...

  • Page 74

    9 technical data 9.5 interfaces 74 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 9.5.1 power supply tab. 32 power supply property xv400 5.7"/8.4"; mc2 5.7" rated voltage 24 vdc selv (safety extra low voltage) permissible voltage rms value: 20.4… 28.8 vdc (rated voltage -15 % / +20...

  • Page 75

    9 technical data 9.6 enclosure ratings micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 75 9.6 enclosure ratings tab. 33 enclosure ratings 9.7 agency approvals and standards tab. 34 agency approvals and standards 1) zone 22, category 3d: - ip5x for devices of the group iiib (non-cond...

  • Page 76

    9 technical data 9.8 applicable standards and regulations 76 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 9.8 applicable standards and regulations tab. 35 applicable standards and regulations property xv400 5.7"/8.4"; mc2 5.7" emc (in relation to ce) iec/en 61000-6-2 immunity for...

  • Page 77

    9 technical data 9.9 ambient conditions micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com 77 9.9 ambient conditions tab. 36 ambient conditions property xv400 5.7"/8.4"; mc2 5.7" temperature operation 0 … 50°c storage / transport -20 … 60°c relative air humidity 10 … 95%, non-condensin...

  • Page 78

    9 technical data 9.9 ambient conditions 78 micro panel xv400 5.7"/8.4" 12/2014 mn04802009z-en www.Eaton.Com.