EAW FB1SB Installation Instructions
HINGE TUBE
REAR
LABEL
FLY - BAR / FB1SB
FRONT
HOLE FOR QUICK DISCONNECT PIN
HOLE FOR
QUICK
DISCONNECT PIN
HINGE TUBE
2X USER
SUPPLIED
SHACKLE
1
2
Eas
ter
n Aco
ust
ic W
ork
s
Wh
itin
svi
lle
, M
A US
A
Te
l : (
5 0
8 )
2 3
4 -
6 1
5 8
WA
RN
ING
Wo
rkin
g L
oad
Lim
it (W
LL)
:
200
0 lb
/ 9
07 k
g
MA
X T
we
lve
(12
) S
B1
002
in
suc
ces
sio
n,
155
lb /
70
.3 k
g e
a.
Fly
-Ba
r =
20
lb /
9.1
kg
.
1
REMOVE QUICK
DISCONNECT PIN
2
3
RAISE
HINGE
LOWER
FLY-BAR
AND FULLY
INSERT
HINGE INTO
HINGE TUBE
HINGE
TUBE
HINGE
4
5
1
2
East
ern
Ac
ou
stic
Wo
rks
Wh
itin
sville
, M
A U
SA
Te
l : (
5 0
8 )
2 3
4 -
6 1
5 8
WAR
NIN
G
Wor
king
Lo
ad Lim
it (W
LL):
2000 lb /
90
7 kg
MAX T
we
lve (12)
SB
1002 in
succ
ess
ion
,
155 lb /
70
.3 k
g ea.
Fly-B
ar =
20 lb /
9.1 kg.
ALIGN HOLES IN
HINGE TUBE AND
HINGE. FULLY INSERT
QUICK DISCONNECT PIN
TO LOCK FLY-BAR TO
ENCLOSURE
ALIGN HOLES IN
HINGE TUBE AND
HINGE. FULLY INSERT
QUICK DISCONNECT PIN
TO LOCK FLY-BAR TO
ENCLOSURE
Installation Instructions
FB1SB Fly-Bar & Rigging
Warning: Suspending Loudspeakers should be done with extreme caution and by a certified professional
who is qualified to determine the requirements for and to implement overhead rigging. Failure to
follow proper precautions may result in
damage to the equipment, injury, or death.
Working Load Limit (WLL): vertical pull
FB1SB Fly-Bar WLL: 2000 lb/ 907 kg
maximum twelve (12) SB1002 in succession
Weights: SB1002: 155 lb/70 kg, Fly-Bar: 20 lb/9 kg
ENCLOSURE
TO FLY-BAR
1
2
Eas
ter
n A
cou
stic
Wo
rks
Wh
itin
svi
lle
, M
A U
SA
Te
l : (
50
8 )
2 3
4 -
6 1
58
WA
RN
ING
Wor
king
Lo
ad Li
mit
(W
LL):
2000
lb / 90
7 k
g
MA
X T
we
lve
(12
) SB
100
2 in
succe
ssio
n,
155
lb / 70
.3 k
g e
a.
Fly
-Bar = 20 l
b / 9.
1 k
g.
FLY-BAR POSITIONED
ABOVE PALLET
OF SB1002
LOUDSPEAKERS
ENCLOSURE TO
ENCLOSURE
CASTER PALLET
FROM
ENCLOSURE
Description:
The FB1SB Fly-Bar is used to suspend up
to 12 SB1002 loudspeakers. These instructions enable a technician to suspend 2 SB1002 Loudspeakers
from the Fly-Bar. To suspend additional SB1002 loudspeakers, refer to the SB1002 Installation Manual.
Rigging Points on the SB1002 Array:
These instructions follow the same sequence a
technician must follow when flying an array of
SB1002 enclosures. The figure to the right shows,
from the top down, the three rigging operations:
A. Enclosure to Fly-Bar,
B. Enclosure to Enclosure
C. Caster Pallet from Enclosure
The three rigging operations are defined by the
following three assembly illustrations.
Rigging tubes, hinges, and their tethered quick disconnect pins are attached to both sides of the SB1002
Loudspeaker. These instructions apply to both the right and left sides of the Fly-Bar, Loudspeakers, and Caster
Pallet. To disassemble the array reverse the sequence of the operations defined in these instructions.
A. Enclosure to Fly-Bar: