1. DL manuals
  2. EBS
  3. Transmitter
  4. LX1NB-5L
  5. Installation And Programming Manual

EBS LX1NB-5L Installation And Programming Manual

Manual is about: GPRS TRANSMITTER

Summary of LX1NB-5L

  • Page 1

    Gprs transmitter lx1nb-5l installation and programming short manual version of the manual: v1.6 date of issue: 2015.04.03.

  • Page 2

    Lx1nb-5l short manual page 2 / 24 declaration of compliance we, ebs sp. Z.O.O. Declare with full responsibility that the present product meets all requirements provided for in the directive 1999/5/ec of european parliament and council dated 9 march 1999 the copy of the “declaration of compliance” ca...

  • Page 3

    Lx1nb-5l short manual page 3 / 24 contents contents .......................................................................................................... 3 1. General information .......................................................................... 4 1.1. Capabilities ........................

  • Page 4: 1.  General Information

    Lx1nb-5l short manual page 4 / 24 1. General information lx1nb-5l is a sms/gprs switch in an ip65 plastic enclosure for the control of gates, doors, lighting, pumps, generators, hvac etc with clip or sms. 1.1. Capabilities lx1nb-5l offers the control of a relay with nc and no outputs. Up to 5 admini...

  • Page 5

    Lx1nb-5l short manual page 5 / 24 1.3. Specifications 1.3.1. Functional inputs: (programmable) 4 signal inputs (no, nc, eol-no, eol-nc, deol-no, deol-nc) outputs: (programmable) 2 (1 x open collector & 1 x relay) operation modes: gprs transmission only sms transmission only gprs and sms transmission...

  • Page 6

    Lx1nb-5l short manual page 6 / 24 1.3.3. Layout below is a schematic of the lx1nb-5l with the explanations of its components. 1. Relay outputs: c (common), nc (normally closed), no (normally open). 2. Prog button. 3. Gsm antenna socket. 4. Sim card slot. 5. Output and input terminals 6. Power supply...

  • Page 7

    Lx1nb-5l short manual page 7 / 24 1.3.4. Terminal description terminal connection description c, nc, no relay outputs. Connection to external device that is to be controlled by switches relay. Gnd device ground, common for other input and output in1 - in4 signal inputs. Possible connection of detect...

  • Page 8

    Lx1nb-5l short manual page 8 / 24 1.3.6. Input configuration inputs in1 - in4 can work as normally closed (nc) or normally open (no). Additionally inputs might be configured as end of line (eol-no or eol-nc) with resistors 2,2kΩ or as double end of line (deol-no or deol-nc) with resistor 1,1kΩ. Figu...

  • Page 9: 2.  Installation

    Lx1nb-5l short manual page 9 / 24 2. Installation caution! For the device to work properly, voice mail has to be disabled 2.1. First run caution! Sim card has to be removed from the device before first run please switch the power supply off before following any of the below instructions. Device can ...

  • Page 10: 3.  Configuration

    Lx1nb-5l short manual page 10 / 24 3. Configuration 3.1. Configuration tool caution! Gprs transmitter’s configurator and full operation manual, describing how to use this software may be downloaded at www.Ebs.Pl (login: ebs, password: ebs) to use the configuration tool, please connect the programmin...

  • Page 11

    Lx1nb-5l short manual page 11 / 24 3.1.2. Relay configuration please select the 3. Inputs/outpus option. Select the relay (out 2) tab. Explanation of the fields: admins - this section allows you configure the administrators programmed in the device. At least one administrator is required for the dev...

  • Page 12

    Lx1nb-5l short manual page 12 / 24 3.2. Sms commands 3.2.1. First run first step is to add a new administrator. At least one administrator is required – if you don’t setup any administrators you will not be able to change the password. To add the administrators please refer to adminadd command. When...

  • Page 13

    Lx1nb-5l short manual page 13 / 24 commands list change password command password= response ‘password changed’ or error message single/multiple single this command can be used to change current password. Default password is 0000. Before the password can be changed, at least one admin has to be progr...

  • Page 14

    Lx1nb-5l short manual page 14 / 24 delete admin command admindelete= response no response single/multiple multi this command can be used to delete admin numbers under a given index. Should be a digit from 0 to 4. Example: 1234 admindelete=2 will delete administrator number saved under index 2. Allow...

  • Page 15

    Lx1nb-5l short manual page 15 / 24 verify user command usercheck= response user found / user not found or error message single/multiple single this command can be used to check if a given number is already programmed in the system. Should be a phone number with the country code, but without ‘00’ or ...

  • Page 16

    Lx1nb-5l short manual page 16 / 24 delete all users command deleteallusers response all users deleted single/multiple single this command can be used to delete all user numbers from the system. Example: 1234 deleteallusers will empty the user number list configure output activation time command conf...

  • Page 17

    Lx1nb-5l short manual page 17 / 24 configure periodic tests command configtest=, response periodic tests configuration changed or error message single/multiple single this command can be used to configure the periodic tests with system status information. These messages will be sent to all administr...

  • Page 18

    Lx1nb-5l short manual page 18 / 24 configure system date and time command dt=--,:: response date and time changed or error message single/multiple single this command can be used to change current system date and time. Should be two last digits of year should be the number of a month should be the h...

  • Page 19: 4.  Led Indicators

    Lx1nb-5l short manual page 19 / 24 4. Led indicators there are 2 led diodes mounted directly on printed circuit board to show the actual condition of the device. 4.1. Logging to gsm network once the sim card has been inserted into the device and the power supply has been turned on, it logs onto the ...

  • Page 20

    Lx1nb-5l short manual page 20 / 24 4.3. Data transmission during data transmission a green diode indicates data transmitting. Description led diodes green red gprs transmission sms transmission 4.4. Programming after detection of programming wire diodes indicate programming. Description led diodes g...

  • Page 21: 5.  Revision History

    Lx1nb-5l short manual page 21 / 24 4.6. Factory default restore if the prog button is pushed in and held during the system start, factory defaults for relay functionality will be restored. This process will be indicated by led diodes flashing in the following sequence: description led diodes green r...

  • Page 22

    Lx1nb-5l short manual page 22 / 24 notes:…………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………… ………………………………………………...

  • Page 23

    Lx1nb-5l short manual page 23 / 24 other products in the ebs range. Available from gm techtronics ltd active track: the personal gps lone worker tracking device with rfid active track trailer: works alongside active track as well as an independent asset tracker active track door: a portable void pro...

  • Page 24

    Lx1nb-5l short manual page 24 / 24 sole distributor of the ebs range throughout the uk and ireland. Gm techtronics ltd unit 17, paxcroft farm hilperton trowbridge wiltshire ba14 6jb 0844 824 6690 info@gmtechtronics.Co.Uk www.Gmtechtronics.Co.Uk.