Summary of PCC-10
Page 1
Pcc/pclta network interface user's guide 078-0450-01a.
Page 2
Ii echelon, lonworks, neuron, lns, lonmaker, and the echelon logo are trademarks of echelon corporation registered in the united states and other countries. Lonsupport and openldv are trademarks of echelon corporation. Other brand and product names are trademarks or registered trademarks of their re...
Page 3: Table of Contents
Pcc/pclta network interfaces user's guide iii table of contents preface ............................................................................................................ V purpose .......................................................................................................... Vi...
Page 4
Iv preface.
Page 5: Preface
Pcc/pclta network interfaces user's guide v preface you can install and configure a pcc-10, pclta-20, or pclta-21 pci network interface card on your computer so that you can manage, test, and monitor and control your l on w orks ® network with an lns ® or openldv ™ application. The pcc/pclta cards s...
Page 6: Purpose
Vi preface purpose this document describes how to install, configure, and test the pcc-10, pclta-20, and pclta-21 network interface cards that you can use to connect an lns or openldv application to a l on w orks network. Audience this guide is intended for developers and end users of l on w orks ne...
Page 7
Pcc/pclta network interfaces user's guide vii region languages supported contact information the americas english japanese echelon corporation attn. Customer support 550 meridian avenue san jose, ca 95126 phone (toll-free): 1-800-258-4lon (258-4566) phone: +1-408-938-5200 fax: +1-408-790-3801 lonsup...
Page 9
Pcc/pclta network interfaces user's guide 1 1 installing and configuring the pcc/pclta network interface cards this chapter describes how to install the pcc/pclta network interface cards and configure them using the l on w orks interfaces application..
Page 10
2 installing and configuring the pcc/pclta network interface cards installing the pcc/pclta network interface cards the following section describes how to install and configure the hardware for the pclta-21, pclta-20, and pcc-10 network interface cards. Make sure the driver software is installed bef...
Page 11
Pcc/pclta network interfaces user's guide 3 configuring the pclta-21 network interface in most cases, pclta-21 initialization occurs automatically upon installation of the card and subsequent power-up of the computer. Manual initialization will be required following software installation to a direct...
Page 12
4 installing and configuring the pcc/pclta network interface cards installing and configuring the pclta-20 network interface the pclta-20/smx interface supports smx transceivers. The pclta-20 card features downloadable memory, a network management interface, and plug n’ play capability with microsof...
Page 13
Pcc/pclta network interfaces user's guide 5 4. To change the system image used by the pclta-20 card, click anywhere in the ni application property, click the box to the right, and then browse to and select the desired system image from the lonworks\images\pclta10 folder. Note: for more information o...
Page 14
6 installing and configuring the pcc/pclta network interface cards 3. The details pane lists the pcc-10 card’s system image and transceiver properties. 4. Optionally, you can modify the pcc-10 card’s transceiver properties following these steps: a. Click anywhere in the transceiver property, and the...
Page 15
Pcc/pclta network interfaces user's guide 7 e. Click ok to save any changes. Note: for more information on configuring, testing, and diagnosing the pcc-10 network interface, see the lonworks interfaces online help..
Page 16
8 installing and configuring the pcc/pclta network interface cards.
Page 17
Pcc/pclta network interfaces user's guide 9 2 electrical and mechanical interfaces this chapter describes the hardware interfaces and mechanical layout of the pcc/pclta cards. ..
Page 18: Pclta-21 Board Layout
10 electrical and mechanical interfaces pclta-21 board layout the following figure shows the layout of the pclta-21 card models 74501, 74502, 74503, and 74504. The pclta-21 card model 74504 (tp-rs485) includes jumpers that must be configured to set the correct speed on the rs-485 channel. P1 and p2 ...
Page 19
Pcc/pclta network interfaces user's guide 11 network connector the pclta-21 model 74501-74503 cards are supplied with a removable two terminal, blz 5180/2/180 for the network connection. The wiring to the twisted pair channel is polarity insensitive. The connector will accept 12 to 26 awg (1.2 mm to...
Page 20: Pclta-20 Board Layout
12 electrical and mechanical interfaces pclta-20 board layout the following figure shows the layout of the pclta-20/smx interface. This card has a header connector for an smx transceiver and does not have an integral transceiver. Attach the smx transceiver in accordance with the manufacturer’s instr...
Page 21
Pcc/pclta network interfaces user's guide 13 the following figure shows the pin-out of the mating female hirose nx30ta-15paa connector to which the network wiring or transceiver pod is connected. The hirose connector plug should be protected with a cover (hirose nx-15t-cv1). The following figure sho...
Page 22
14 electrical and mechanical interfaces the following table describes the electrical characteristics of the card’s digital inputs and outputs. Network connector the pcc-10 card includes a standard 68-pin computer pc card connector for interfacing with a host computer or embedded controller. This con...
Page 23
Pcc/pclta network interfaces user's guide 15 the switchcraft a3mbau xlr male connector is compatible with a wide variety of female connectors, as shown in the following table. You can create a general purpose cable that includes a 15-pin hirose connector, a two or 14-conductor cable plus shield, and...
Page 24
Www.Echelon.Com.