P ower e dger a ttachment o perator ' s m anual 1 power edger attachment operator's manual model 99944200470 serial number 001001 - 057000 models used on: srm-2100sb/2400sb srm-210sb/211sb srm-260sb/261sb pas 2100/2400 pas 210/211 pas 230/231 pas 260/261 x7532278700 x753001210 08/02 warning danger r...
2 i ntroduction welcome to the echo family. This echo product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the safety manual you found in the same package. You will find both easy to use and full of helpful operating tips and s...
P ower e dger a ttachment o perator ' s m anual 3 s afety decals locate these safety decals on your unit. The complete unit illustration found in the "description" section, will help you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a d...
4 symbol description/application symbol form/shape symbol description/ application symbol form/shape hot surface carburetor adjustment - idle speed carburetor adjustment - high speed mixture symbol description/application symbol form/shape symbol description/ application symbol form/shape read and u...
P ower e dger a ttachment o perator ' s m anual 5 extended operation / extreme conditions vibration and cold -- it is believed that a condition called raynaud’s phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration ...
6 d escription after opening the carton, check for damage. Immediately notify your retailer or echo dealer of damaged or missing parts. Use the contents list to check for missing parts. 1 5 6 4 3 2 1. Debris shield/flap - mounted over the cutting attachment. Helps protect operator by deflecting debr...
P ower e dger a ttachment o perator ' s m anual 7 s pecifications model ----------------------------------------------------- power edger attachment shaft length ------------------------------------------------ 845 mm (33.25in.) attachment width ----------------------------------------- 165.1 mm (6....
8 4. Rotate locator pin (a) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by twisting lower drive shaft. Locator pin should snap flush in coupler. Full engagement will prevent further shaft rotation. 5. Secure lower shaft assembly to coupler by tightening clampin...
P ower e dger a ttachment o perator ' s m anual 9 increase depth wheel adjustment knob decrease depth 1/2 in. 4. Adjust the blade's depth of cut to produce a fine cut between sidewalk and grass using a minimum blade depth, usually with about 13 mm (1/2 in.) of the blade into the ground. 5. Before ed...
10 blade replacement / lubrication level 1. Tools required: scrench, locking tool, needle nose pliers, 8 mm open end wrench, grease gun parts required: echo ® lube tm 8 oz. (p/n 91014) or lithium base grease, blade p/n 69601552632 gear case note grease gear case every 50 hours of use. Replace blade ...
P ower e dger a ttachment o perator ' s m anual 11 drive shaft (lower) important lower and upper drive shaft must be lubricated with high temperature automotive grease every 25 hours of operation, otherwise drive shaft assembly overheating and failure can result. 1. Loosen two (2) screws (a) and rem...
Echo, incorporated 400 o akwood r oad l ake z urich , il 60047 www.Echo-usa.Com dealer? Call 1-800-432-echo www.Echo-usa.Com consumer product support 1-800-673-1558 8:30 - 4:30 mon - fri c.S.T. S ervicing i nformation parts genuine echo parts and echo repower™ parts and assemblies for your echo prod...
Specification (pg. 7) gear ratio ----------------------------- 2.07:1 weight w/blade ---------------------- 2.54 kg (5.6 lbs.) maintenance (pg. 9) maintenance intervals drive shaft every 50 hours of use gear housing every 15-25 hours of use blade replacement/lubrication (pg. 10) tools required: 13 m...
