1. DL manuals
  2. Echo
  3. Saw
  4. CS-355T
  5. Instruction Manual

Echo CS-355T Instruction Manual

Manual is about: Echo CHAIN SAW

Summary of CS-355T

  • Page 1

    Chain saw instruction manual model : cs-355t warning x7503320104 06/13 users of this equipment risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Echo provides an operator's manual and a safety manual. Both must be read and understood for ...

  • Page 2: Contents

    2 cs-355t copyright© 2013 by echo, incorporated all rights reserved. Contents contents .............................................................................................................. 2 packing list ..........................................................................................

  • Page 3: Packing List

    3 cs-355t packing list the echo product you purchased has been fac- tory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage. Im- mediately notify your retailer or echo...

  • Page 4: Rules For Safe Operation

    4 cs-355t rules for safe operation kickback safety precautions for chain saw users 1. With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. 2. Keep a good firm grip on the saw with both hands, the right hand on the rear...

  • Page 5: Correct Use of Chain Brake

    5 cs-355t correct use of chain brake the installation of a chain brake may be mandatory by law or as stipulated by insurance regulations in your area of operation. You should inquire through local government offices, your employer or your local dealer to ensure that your chain saw conforms to the re...

  • Page 6

    6 cs-355t end of the guide bar may be placed at the height of about 55 cm (22 in.). 55 cm (22 in.) automatic chain brake kickback produced from the tip of the guide bar will trip the automatic chain brake. To make sure that the automatic chain brake operates properly, follow these steps: 1. Stop the...

  • Page 7

    7 cs-355t 12. Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance. 13. When cutting a limb that is under tension, be alert for spring-back so that you will not be struck when the tension in ...

  • Page 8: Operator Safety

    8 cs-355t operator safety vibration and cold • it is believed that a condition called raynaud’s phe- nomenon, which affects the fingers of certain individu- als, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning followed by loss of ...

  • Page 9: Symbols and Signs

    9 cs-355t carburetor adjustment - idle speed carburetor adjustment - high speed mixture warning!! Read and follow all safety precaution in the instruction manual. Failure to follow instructions could result in serious personal injury. Wear eyes, ears and head protection carburetor adjustment - low s...

  • Page 10: Emission Data

    10 cs-355t decals locate this safety decal on your unit. The complete unit illustration found in the “nomenclature of parts” section will help you locate them. Make sure the decal is legible and that you under- stand and follow the instructions on it. If a decal cannot be read, a new one can be orde...

  • Page 11: Description of Parts

    11 cs-355t description of parts 19 14 15 17 16 2 1 21 22 20 23 18 13 5 4 7 11 12 3 10 6 8 9.

  • Page 12: Description of Parts

    12 cs-355t 1. Instruction manual - included with unit. Read be- fore operation and keep for future reference to learn proper, safe operating techniques. 2. Safety manual - describe operating and safety instructions for this chain saw. 3. Chain brake lever/front hand guard - guard between the front h...

  • Page 13: Preparation For Use

    13 cs-355t preparation for use warning saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. Note the machine may be delivered with guide bar, tip guard, and saw chain separated. Install guide bar, tip guard, and saw chain as follows. Kick guard...

  • Page 14

    14 cs-355t 4. Mount guide bar on studs and slide toward clutch to make saw chain installation easier. Install chain with cutters on top of guide bar facing forward. 5. Unlock the chain brake, and install the clutch cover over the guide bar studs. Ensure chain tension adjust- er pin fits into the gui...

  • Page 15

    15 cs-355t handling fuel warning fuel is very flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • use an approved fuel container. • do not smoke near fuel. • do not allow flames or sparks near fuel. • fuel tanks/cans may be under pressure. Always loo...

  • Page 16

    16 cs-355t important stored fuel ages. Do not mix more fuel than you ex- pect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Important stored two-stroke fuel may separate. Always shake fuel container thoroughly before each use. Oil tank cap fuel tank cap mixing instruc...

  • Page 17: Operation

    17 cs-355t operation cold start chain brake starter handle purge pump control lever warning moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come t...

  • Page 18

    18 cs-355t cold start chain brake starter handle purge pump control lever chain brake control lever run (i) purge pump control lever run (i) when the engine is warm caution make sure the bar and chain are free from any obstruction when starting the chain saw. • move chain brake lever fully forward t...

  • Page 19

    19 cs-355t stop control lever throttle trigger unlock chain brake running warning the saw chain should not move at idle, otherwise serious personal injury may result. Note if saw chain moves adjust carburetor according to “carburetor adjustment” instructions in this manual, or see your dealer. • whe...

  • Page 20: Cutting Instruction

    20 cs-355t cutting instruction general warning • read the echo “chain saw safety manual” included with your chain saw for additional cutting and safety instructions. • wear suitable hearing protection such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. • do no...

  • Page 21

    21 cs-355t felling the tree warning a falling tree can seriously damage anything it may hit - a car, a house, a fence, a power-line, or an- other tree.There are ways to make a tree fall where you want it, so first decide where that is! Before cutting, clear the area around the tree. You will need go...

  • Page 22

    22 cs-355t limbing limbing a fallen tree is much the same as bucking. Never stand on the tree that you are limbing. When limbing, caution is the word. Be careful of the tip touching other limbs. Always use both hands. Don’t cut with the saw overhead or aligned vertical- ly with your body. If the saw...

  • Page 23

    23 cs-355t chain and guide bar combination the following combinations are recommen ded for model cs-355t. Guide bar (low-kickback) replacement guide bars. The following guide bars may be considered to have equivalent kickback energy. • sprocket nose guide bars of the same length and nose radius, sam...

  • Page 24

    24 cs-355t m aintenance and c are warning moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a com- plete stop before removing obstructions, ...

  • Page 25

    25 cs-355t idle adjusting screw low speed needle (l) high speed needle (h) carburetor adjustment every unit is run at the factory and the carburetor is set in compliance with emission regulations. In addition, the carburetor is equipped with “h” (high speed) and “l” (low speed) needle adjustment lim...

  • Page 26

    26 cs-355t oil filter fuel filter oil tank cap fuel tank cap 0.65 mm (0.026 in.) check fuel system • check before every use. • after refueling, make sure fuel does not leak from around fuel pipe, fuel grommet or fuel tank cap. • in case of fuel leakage there is a danger of fire. Stop using the machi...

  • Page 27

    27 cs-355t worn : 0.5 mm (0.02 in.) spark arrestor screen muffler screen cover adjusting screw cylinder fins decrease increase spark arrestor muffler • the spark arrestor muffler controls the exhaust noise and prevents hot, glowing particles of carbon from leaving the muffler. • make sure the spark ...

  • Page 28

    28 cs-355t exhaust port cleaning level 2. Parts required: as needed: muffler gasket 1. Remove spark plug cover (a) and remove spark plug lead (b). 2. Release chain brake, and remove guide bar nuts, clutch cover, guide bar, and chain. 3. Remove muffler cover screws and remove muffler cover. (see “gui...

  • Page 29

    29 cs-355t setting the saw chain sharpen lower edge drive link tie strap right hand cutter preset tie strap left hand cutter guard link top plate side plate depth guage important points for proper maintenance of saw chain: • keep the cutters sharp at all times. • keep the left and the right cutters ...

  • Page 30

    30 cs-355t note these angles are referred to as 91px. To sharpen other chains, follow chain manufac- turer’s instructions. • place the depth gauge tool firmly on guide bar so that depth gauge protrudes. Then file top of depth gauge with the flat file until flat with top of the depth gauge tool. • be...

  • Page 31: Troubleshooting

    31 cs-355t troubleshooting t r a h c g n i t o o h s e l b u o r t m e l b o r p e n i g n e m e l b o r p k c e h c s u t a t s e s u a c y d e m e r e n i g n e - s k n a r c / d r a h s tr a t s t' n s e o d tr a t s r o t e r u b r a c t a l e u f r o t e r u b r a c t a l e u f o n d e g g o lc...

  • Page 32: Storage After Use

    32 cs-355t storage after use warning do not store in an enclosure where fuel fumes may accumulate or reach an open flame or spark. Caution do not lend or rent your chain saw without the instruction manual and safety manual. Note • for future reference, you should keep this instruction manual and the...

  • Page 33: Technical Data

    33 cs-355t * technical data subject to change without notice. Technical data model cs-355t dimension l × w × h mm 287 × 244 × 220 (11.3 in. × 9.6 in. × 8.7 in.) mass power head, dry kg 3.5 (7.72 lb.) without chain and guide bar engine type air-cooled two-stroke single cylinder displacement ml (cm³) ...

  • Page 34: Warranty Statements

    34 cs-355t warranty statements echo limited warranty statement for product sold in usa and canada beginning 01/01/2010 echo's responsibility echo incorporated’s limited warranty, provides to the original purchaser that this echo product is free from defects in material and workmanship. Under normal ...

  • Page 35

    35 cs-355t purchased repair parts, short blocks and accessories • 90-day residential, or non-income producing warranty • 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty attention two-stroke engine power product owners this echo two-stroke ...

  • Page 36

    Echo, incorporated 400 o akwood r oad l ake z urich , il 60047 www.Echo-usa.Com consumer product support 1-800-673-1558 8:30 - 4:30 mon - fri c.S.T. Dealer? Call 1-800-432-echo 1-800-432-3246 or www.Echo-usa.Com s ervicing i nformation parts / serial number genuine echo parts and echo repower™ parts...