1. DL manuals
  2. Echo
  3. Chainsaw
  4. CS-4510
  5. Operator's Manual

Echo CS-4510 Operator's Manual

Summary of CS-4510

  • Page 1

    1 cs-4510 operators manual chain saw cs-4510 warning read the instructions carefully and follow the rules for safe operation. Failure to do so could result in serious injury. X7503350601 echo, incorporated 400 oakwood road, lake zurich, illinois 60047-1564 phone : 847-540-8400 1/18 this product comp...

  • Page 2

    2 cs-4510 copyright © 2017 all rights reserved. The engine exhaust from this product contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Warning.

  • Page 3: Rules For Safe Operation

    3 cs-4510 rules for safe operation a. Kickback safety precautions for chain saw users 1. With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. 2. Keep a good firm grip on the saw with both hands, the right hand on the r...

  • Page 4

    4 cs-4510 1. Do not operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders, or any combination of these persons may result from one-handed operation. A chain saw is intended for two-handed use. 2. Do not operate a chain saw when you are fatigued. 3. Use safety footwea...

  • Page 5: Symbols and Signs

    5 cs-4510 warning the safety alert symbol accompanied by the word “warning” calls attention to an act or condition which can lead to serious personal injury or death if not avoided. Caution the safety alert symbol accompanied by the word “caution” calls attention to an act or condition which may lea...

  • Page 6: Stop

    6 cs-4510 symbol form locate this safety decal on your unit. The complete unit illustration found in the “nomenclature of parts” section will help you locate them. Make sure the decal is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be or...

  • Page 7: Packing List

    7 cs-4510 packing list the echo product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or echo dea...

  • Page 8: Nomenclature of Parts

    8 cs-4510 nomenclature of parts * if a decal cannot be read, a new one can be ordered from your echo dealer. 21 16 17 19 18 5 4 8 7 10 11 12 3 1 x505-010090 9 23 6 24 22 20 15 part number x505-010090 13 14 2 operators 25.

  • Page 9: Nomenclature of Parts

    9 cs-4510 1. Operators manual - included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Safety manual - describe operating and safety instructions for this chain saw. 3. Spark arrestor muffler - the spark arrestor muffler controls the ex...

  • Page 10: Operator Safety

    10 cs-4510 operator safety vibration and cold • it is believed that a condition called raynaud’s phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning followed by loss of col...

  • Page 11: Correct Use of Chain Brake

    11 cs-4510 spark arrestor muffler • the spark arrestor muffler controls the exhaust noise and prevents hot, glowing particles of carbon from leaving the muffler. Make sure the spark arrestor screen is in good repair and properly seated in the muffler. • certain internal combustion engines operated o...

  • Page 12: Preparation For Use

    12 cs-4510 warning saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. Guide bar and saw chain installation/removal notice • move the chain brake lever (front hand guard) fully rearward to remove or install the clutch cover to chain saw. • ali...

  • Page 13

    13 cs-4510 adjusting chain tension important always loosen clutch cover nuts before turning the chain tension adjuster, otherwise the clutch cover and tensioner will be damaged. 1. Remove spark plug lead. (see maintenance sec- tion) 2. Unlock the chain brake and loosen a clutch cover nuts, if necess...

  • Page 14: Fuel and Lubricant

    14 cs-4510 warning diesel fuels and alternative fuels, such as e-15 (15% ethanol), e-85 (85% ethanol) or any fuels not meeting echo requirements are not approved for use in echo 2-stroke gasoline engines. Use of diesel or alternative fuels may cause performance problems, loss of power, overheating, ...

  • Page 15

    15 cs-4510 handling fuel mixing instructions - 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. I...

  • Page 16: Emission Data

    16 cs-4510 emission data emission control (exhaust and evaporative) epa 2010 and/ or c.A.R.B. Tier iii the emission control system for the engine is em/ twc (engine modification and 3-way catalyst) and for the fuel tank the control system is evap (evaporative emissions) or n (for nylon tank). Evapor...

  • Page 17: Operation

    17 cs-4510 operation chain brake starter handle throttle trigger choke throttle trigger lockout purge pump warning • after choke control knob is pulled and then knob is returned to original position, throttle remains slightly open (fast idle latch condition). • the chain will attempt to move when en...

  • Page 18

    18 cs-4510 chain brake starter handle throttle trigger choke throttle trigger lockout purge pump chain brake starter handle when the engine is cold caution make sure the bar and chain are free from any obstruction when starting the chain saw. • move chain brake lever fully forward to lock chain brak...

  • Page 19

    19 cs-4510 running • when engine starts, keep idling for a few minutes. • set the brake lever in the unlocked position before starting to cut. • pull throttle trigger gradually and increase revolution of the engine. • the chain starts running when the engine reaches 4,150 r/min approximately. • conf...

  • Page 20: Cutting Instruction

    20 cs-4510 cutting instruction general caution • read the echo “chain saw safety manual” included with your chain saw for additional cutting and safety instructions. • wear suitable hearing protection such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. • do no...

  • Page 21

    21 cs-4510 felling the tree a falling tree can seriously damage anything it may hit - a car, a house, a fence, a power-line, or another tree. There are ways to make a tree fall where you want it, so first decide where that is! Before cutting, clear the area around the tree. You will need good footin...

  • Page 22

    22 cs-4510 limbing limbing a fallen tree is much the same as bucking. Never stand on the tree that you are limbing. When limbing, caution is the word. Be careful of the tip touching other limbs. Always use both hands. Don’t cut with the saw overhead or aligned vertically with your body. If the saw s...

  • Page 23

    23 cs-4510 chain brake function when the lever is pushed forward, chain brake instantly stops the chain. Chain brake unlock when the lever is fully pulled toward the operator, brake is unlocked. When the bar nose hits another tree, etc. Improper thrust cutting chain brake operation • set the lever i...

  • Page 24

    24 cs-4510 end of the guide bar may be placed at the height of about 50 cm (20 in.). 50 cm (20 in.) automatic chain brake kickback produced from the tip of the guide bar will trip the automatic chain brake. To make sure that the automatic chain brake operates properly, follow these steps: 1. Stop th...

  • Page 25

    25 cs-4510 chain and guide bar combination the following combinations are recommended for model cs-4510. Guide bar (low-kickback) replacement guide bars. The following guide bars may be considered to have equivalent kickback energy. • sprocket nose guide bars of the same length and nose radius, same...

  • Page 26: Maintenance and Care

    26 cs-4510 maintenance and care important time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. Your echo chain saw is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your chain saw achie...

  • Page 27

    27 cs-4510 carburetor adjustment every unit is run at the factory and the carburetor is set in compliance with emission regulations. In addition, the carburetor is equipped with “h” (high mix) and “l” (low mix) needle adjustment limiters that prevent settings outside acceptable limits. 1. Before adj...

  • Page 28

    28 cs-4510 0.65 mm (0.026 in.) cleaner cover latch air filter air cleaner cover air filter • check before every use. • close choke ( ). • release the cleaner cover latch. • pull air cleaner cover back and up to remove. • remove the air filter by turning it counterclockwise. • brush off dust lightly,...

  • Page 29

    29 cs-4510 fuel filter fuel tank cap fuel filter • check periodically. • do not allow dust to enter fuel tank. • a clogged filter will cause difficulty in starting engine or abnormalities in engine performance. • pull the fuel filter out through fuel inlet port with a piece of steel wire or the like...

  • Page 30

    30 cs-4510 cylinder fins • check daily or before use. • clogged fins will result in poor engine cooling. • remove the air cleaner cover and the air filter, and the spark plug lead. • remove the three bolts of the cylinder cover. • loosen the two mounting bolts of the cleaner case. • lift the cylinde...

  • Page 31: Setting The Saw Chain

    31 cs-4510 setting the saw chain sharpen lower edge drive link tie strap right hand cutter preset tie strap left hand cutter guard link top plate side plate depth gauge hold the file tipped 10° upward 10° important points for proper maintenance of saw chain: • keep the cutters sharp at all times. • ...

  • Page 32

    32 cs-4510 • place the depth gauge tool firmly on guide bar so that depth gauge protrudes. Then file top of depth gauge with the flat file until flat with top of the depth gauge tool. - be sure to round off the front edge of the depth gauge. Properly filed cutters are shown in illustration. When set...

  • Page 33: Troubleshooting

    33 cs-4510 troubleshooting warning fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. Problem engine — hard to start cause remedy — does not start engine...

  • Page 34: Technical Data

    34 cs-4510 * technical data subject to change without notice. Technical data model cs-4510 dimension l × w × h mm (in) 437 × 237 × 298 (17.2 × 9.3 × 11.7) mass power head, dry kg (lb) 5.0 (11) without chain and guide bar engine type air-cooled two-stroke single cylinder displacement ml (in³) 45.0 (2...

  • Page 35: Warranty Registration Sheet

    35 cs-4510 warranty registration sheet thank you for choosing echo power equipment please go to http://www.Echo-usa.Com/warranty/register-your-echo to register your new product on-line. It’s fast and easy! Note: your information will never be sold or misused by echo, inc. Registering your purchase e...

  • Page 36

    36 cs-4510 c71315001001 - c71315999999.