Instruction manual chain saw cs-530 warning read the instructions carefully and follow the rules for safe operation. Failure to do so could result in serious injury. X750-011 30 1 x750 319-710 1 echo, incorporated 400 oakwood road, lake zurich, illinois 60047-1564 phone : 847-540-8400 printed in jap...
Copyright © 2007 all rights reserved. The engine exhaust from this product contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Warning.
1 cs-530 rules for safe operation a. Kickback safety precautions for chain saw users 1.With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. 2.Keep a good firm grip on the saw with both hands, the right hand on the rear...
2 cs-530 1.Do not operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders, or any combination of these persons may result from one-handed operation. A chain saw is intended for two- handed use. 2.Do not operate a chain saw when you are fatigued. 3.Use safety footwear, ...
3 cs-530 contents warning the safety alert symbol accompanied by the word “warning” calls attention to an act or condition which can lead to serious personal injury or death if not avoided. Circle and slash symbol this symbol means the specific action shown is prohibited. Ignoring these prohibitions...
4 cs-530 to avoid kickback 1. Hold the chain saw firmly with both hands. 2. Don’t let the nose of the guide bar contact any obstruction. 3. Tip contact may suddenly move the guide bar upward and backward, which may cause serious injury. Part number 890191-30131 carburetor adjustment - idle speed car...
5 cs-530 packing list the echo product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or echo deal...
6 cs-530 nomenclature of parts * if a decal cannot be read, a new one can be ordered from your echo dealer. 23 20 15 16 17 19 18 14 5 4 7 6 9 10 11 12 13 3 2 1 x524-002000 890191-30131 x503-009050 8 21 22 part number x503-009050 warning!! Read and follow all safety precaution in the instruction manu...
7 cs-530 nomenclature of parts 1. Instruction manual - included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Safety manual - describe operating and safety instructions for this chain saw. 3. Front hand guard - guard between the front h...
8 cs-530 vibration and cold • it is believed that a condition called raynaud’s phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning followed by loss of color and numbness in...
9 cs-530 spark arrestor muffler • the spark arrestor muffler controls the exhaust noise and prevents hot, glowing particles of carbon from leaving the muffler. Make sure the spark arrestor screen is in good repair and properly seated in the muffler. • certain internal combustion engines operated on ...
10 cs-530 preparation for use bolt (a) dimple (d) recess (e) front hole (c) rear hole (b) nut (f) guide bar kick guard ® brake connector clutch cover brake lever (front hand guard) two nuts warning saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may r...
11 cs-530 5. Mount guide bar on studs and slide toward clutch to make saw chain installation easier. Install chain with cutters on top of guide bar facing forward. 6. Unlock the chain brake, and install the clutch cover over the guide bar studs. Ensure chain tension adjuster pin fits into the guide ...
12 cs-530 fuel and lubricant fuel mix chart 50 : 1 us. Metric gasoline oil gasoline oil gallons us. Fl. Oz. L ml 1 2.6 4 80 2 5.2 8 160 5 12.8 20 400 fuel statement gasoline - use 89 octane [(r+m)/2] (mid grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10 % e...
13 cs-530 handling fuel mixing instructions - 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. Im...
14 cs-530 oil tank cap fuel tank cap cap indication fuel/oil tanks are indicated by the following illustrations. Chain lubricant proper lubrication of the chain while in operation reduces friction between the chain and the guide bar to a minimum and assures a longer service life. • use bar and chain...
15 cs-530 when the engine is cold caution make sure the bar and chain are free from any obstruction when starting the chain saw. • move chain brake lever fully forward to lock chain brake before starting. • fill the fuel tank with fuel mixture. It is not permitted to fill fuel above the shoulder lev...
16 cs-530 stop ignition switch throttle trigger running • when engine starts, keep idling for a few minutes. • set the brake lever in the unlocked position before starting to cut. • pull throttle trigger gradually and increase revolution of the engine. • the chain starts running when the engine reac...
17 cs-530 cutting instruction kickback general caution • read the echo “chain saw safety manual” included with your chain saw for additional cutting and safety instructions. • wear suitable hearing protection such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises....
18 cs-530 felling the tree a falling tree can seriously damage anything it may hit - a car, a house, a fence, a power-line, or another tree. There are ways to make a tree fall where you want it, so first decide where that is! Before cutting, clear the area around the tree. You will need good footing...
19 cs-530 uphill position finish cut first cut limbing limbing a fallen tree is much the same as bucking. Never stand on the tree that you are limbing. When limbing, caution is the word. Be careful of the tip touching other limbs. Always use both hands. Don’t cut with the saw overhead or aligned ver...
20 cs-530 chain brake function when the lever is pushed forward, chain brake instantly stops the chain. Chain brake unlock when the lever is fully pulled, toward the operator, brake is unlocked. Kickback kickback motion chain brake operation • set the lever in the unlocked position before starting t...
21 cs-530 end of the guide bar may be placed at the height of about 50 cm (20 in.). 50 cm (20 in.) automatic chain brake kickback produced from the tip of the guide bar will trip the automatic chain brake. To make sure that the automatic chain brake operates properly, follow these steps: 1. Stop the...
22 cs-530 chain and guide bar combination the following combinations are recommended for model cs-530 . @ standard configuration guide bar (low-kickback) replacement guide bars. The following guide bars may be considered to have equivalent kickback energy. • sprocket nose guide bars of the same leng...
23 cs-530 maintenance and care important time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. Your echo chain saw is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your chain saw achiev...
24 cs-530 carburetor adjustment every unit is run at the factory and the carburetor is set in compliance with emission regulations. In addition, the carburetor is equipped with “h” (high speed) and “l” (low speed) needle adjustment limiters that prevent settings outside acceptable limits. 1. Before ...
25 cs-530 oil filter fuel filter oil tank cap fuel tank cap 0.65 mm (0.026 in.) air filter • check before every use. • loosen cleaner cover knob and remove air cleaner cover and filter. • brush off dust lightly, or clean with compressed air, or replace the air filter. • reinstall air filter and cove...
26 cs-530 guide bar • clean before using. - clean the groove of the guide bar with a small screwdriver. - clean oil holes with a wire. • reverse guide bar periodically. • check sprocket and the clutch and clean the bar mount area before installation of the bar. Replace either or both if worn. Sprock...
27 cs-530 setting the saw chain sharpen lower edge drive link tie strap right hand cutter preset tie strap left hand cutter guard link top plate side plate depth guage important points for proper maintenance of saw chain: • keep the cutters sharp at all times. • keep the left and the right cutters p...
28 cs-530 note these angles are referred to as oregon 33sl or 95vp. To sharpen other follow chain manufacturer’s instruction. • place the depth gauge tool firmly on guide bar so that depth gauge protrudes. Then file top of depth gauge with the flat file until flat with top of the depth gauge tool. -...
29 cs-530 troubleshooting problem engine — hard to start cause remedy — does not start engine fuel at no fuel • fuel filter clogged • clean or replace cranks carburetor at carburetor • fuel line clogged • clean • carburetor • ask your echo dealer fuel at no fuel at • carburetor • ask your echo deale...
30 cs-530 storage after use technical data • inspect and adjust every part of the chain saw. - completely clean every part and repair if necessary. - apply thin coating of oil on metal parts to prevent rust. • remove chain and guide bar. • drain fuel tank, pull starter slowly a few times to drain fu...