Echo CS-8001 Service Data

Manual is about: Echo CS-8001 Chain Saw

Summary of CS-8001

  • Page 1

    Cs-8001 01-81b-00 1 introduction we are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications and directions in this service data are based on the latest products i n f o r m a t i o...

  • Page 2

    Service information cs-8001 2 1 service information 1-1 specifications dimensions length* mm(in) 421 (16.58) width mm(in) 244 (9.61) height mm(in) 311 (12.24) dry weight* kg(lb) 7.5 (16.5) engine type kioritz, air-cooled, two-stroke, single cylinder ventilated piston rotation clockwise as viewed fro...

  • Page 3

    Service information cs-8001 3 1-2 technical data engine idling speed r/min 2300 - 3300 operating speed r/min 9000 - 9500 wide open throttle speed* r/min 11500 - 12500 clutch engagement speed r/min 3500 - 4000 compression pressure mpa (kgf/cm 2 ) (psi) 0.98 (10.0) (142) ignition system spark plug gap...

  • Page 4

    Service information cs-8001 4 1-3 torque limits descriptions size kgf•cm n•m in•lbf starter starter center post screw m 5* 70 - 110 7 - 11 60 - 95 system starter pawl m 5* 70 - 110 7 - 11 60 - 95 starter case m 5 50 - 60 5 - 6 45 - 50 ignition magneto rotor (flywheel) m 8 230 - 270 23 - 27 200 - 240...

  • Page 5

    Service information cs-8001 5 1-4 special repairing materials material location remarks adhesive stud bolt loctite #609, threebond 1373 or equivalent bellows holder intake insulator loctite #406 (424), threebond 1741 cushion (rear handle) or equivalent check valve assembly thread locking sealant sta...

  • Page 6

    Service information cs-8001 6 0 5 10 1 2 3 4 5 6 7 8 9 10 11 5k083 5k084 5k081 5k082 5k016 5k042 5k172 5k173 5k175 5k171 5k097 5k171 1-5 service limits a b c d e f g h k l m p n description mm (in) a cylinder bore when plating is worn and aluminium can be seen b piston outer diameter min. 51.82 (2.0...

  • Page 7

    Service information cs-8001 7 a b 20 20 40 40 60 60 80 80 1 20 120 140 140 160 160 180 180 20 20 100 100 1-6 special tools 1 5 7 2 8 11 12 13 15 17 18 19 21 3 9 key part number description used for: 1 897801-33330 tachometer pet-1000 measuring engine speed to adjust carburettor 2 895610-79920 l-hex ...

  • Page 8

    Service information cs-8001 8 2 emission adjustment guide 2-1 general adjusting rules before starting the unit for adjustment, check the following items. 1. The correct spark plug must be clean and properly gapped. 2. The air filter element must be clean and properly installed. 3. The muffler exhaus...

  • Page 9

    Service information cs-8001 9 2-3 adjusting carburettor 1. Start engine and warm it up well for 2 -3 minutes with cycle of 5 seconds at wot (wide open throttle) and 10 seconds at idling. 2. Using 2.5 mm wide blade screw driver, adjust l mixture needle to obtain maximum idle speed. 3. Set idle speed ...

  • Page 10

    Service information cs-8001 9 2-3 adjusting carburettor 1. Start engine and warm it up well for 2 -3 minutes with cycle of 5 seconds at wot (wide open throttle) and 10 seconds at idling. 2. Using 2.5 mm wide blade screw driver, adjust l mixture needle to obtain maximum idle speed. 3. Set idle speed ...