1. DL manuals
  2. Echo
  3. Tools
  4. EDR-260
  5. Operator's Manual

Echo EDR-260 Operator's Manual

Other manuals for EDR-260: Operator's Manual, Operator's Manual

Summary of EDR-260

  • Page 1

    Operator manual engine drill edr-260 x750-025 62 1 x750409-4601 warning read instructions carefully and follow rules for safe operation. Failure to do so could result in serious injury. Echo, incorporated 400 oakwood road, lake zurich, illinois 60047-1564 phone : 847-540-8400 printed in japan 1305sf...

  • Page 2: Warning

    Warning some dust created by power sanding, sawing, grinding, drilling, and oth- er construction activities contains chemicals known to the state of cal- ifornia to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: •lead from lead-based paints, •crystallin...

  • Page 3: Introduction

    1 caution the safety alert symbol accompanied by the word “caution” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. Warning improper use or care of this unit, or failure to wear proper protection can result in serious injury. Read and unders...

  • Page 4: Safety

    2 warning always stop the engine when a drill jam occurs. Do not attempt to remove an object causing a drill jam if the engine is running. Physical injury can occur if a drill jam is removed and the drills start moving. • do all drilling at full throttle speed. Drilling at less at than full speed ca...

  • Page 5

    3 wear non-slip, heavy-duty work gloves to improve your grip on the engine drill handles. The gloves also help reduce the transmission of machine vibrations to your hands. Protecting others spectators, children, fellow workers and animals must be warned to come no nearer than 4.6 m (15 feet) while t...

  • Page 6

    4 repetitive stress injuries it is believed that over-using the muscles and tendons of the fi ngers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a repetitive s...

  • Page 7: Operating Techniques

    5 • do not force the drills and only move as quickly as the drills will allow. • stop the engine and disconnect from ignition cable before: - cleaning or when clearing a blockage; checking, maintenance or working on the machine. • handle fuel with care; it is highly fl ammable. Never add fuel to a m...

  • Page 8: Description

    6 description 1. Operator’s manual - included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Throttle trigger - device activated by the operator’s fi nger, for controlling the engine speed. 3. Rear handle - handle located furthest from t...

  • Page 9: Assembling

    7 assembling front handle • insert the front handle to the machine, and turn clockwise. (tighten the screw firmly) - to operate front handle with right hand, remove right plug then reverse sides when installing handle and plug. Drill bit • insert the drill bit (not provided with unit) until it reach...

  • Page 10

    8 check up of nuts and other hardwares • check up loose nuts, bolts and screws before using the unit every day. Fuel statement gasoline - use 89 octane [(r+m)/2] (mid grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10 % ethyl (grain) alcohol or 15 % mtbe (met...

  • Page 11

    9 handling fuel mixing instructions - 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-stroke oil to gaso- line. 3. Close container and shake to mix oil with gaso- line. 4. Add remaining gasoline, close fuel container, and remix. Import...

  • Page 12

    10 on stop throttle trigger note when engine does not stop, shift choke lever to close position. Check and repair ignition switch before starting the engine again. Starting cold engine stopping engine • set throttle trigger in idle position. • place ignition switch in stop position. Starting warm en...

  • Page 13: Maintenance and Care

    11 reverse rotation • this model is equipped with reverse rotation mechanism. • when drilling, set shift lever down to clockwise (cw) rotation position. • if bit is locked due to deep penetration during drilling operation, set shift lever up to counterclockwise (ccw) rotation position and operate re...

  • Page 14: Emission Data

    12 important time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance. Record dates of monthly and yearly inspections. Emission data emission control (exhaust and evaporative) epa 2010 and later and/or c.A.R.B. Tier iii the emission control syst...

  • Page 15: Trouble Shooting

    13 warning • all engine drill service operations, other than items listed in the operator’s manual, should be performed by an authorized echo dealer. • fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug ho...

  • Page 16: Maintenance

    14 maintenance air filter • clean before use. - remove air cleaner cover and pull out air fi lter. - lightly brush off dust or wash it in water and detergent. - dry completely before putting it back in place. Fuel fi lter fuel tank cap spark plug • check periodically. - the standard spark gap is 0.6...

  • Page 17

    15 adjusting carburetor (as required) general information the idle speed adjuster screw controls the throttle opening at the idle position. Idle adjustment 1. Start engine and allow it to run at high idle until warm. 2. Turn the idle speed screw clockwise until drill bit begins to move. 3. Turn idle...

  • Page 18

    16 cleaning cylinder fins (check periodically) note clogged fi ns will cause poor engine cooling. 1. Carefully remove housing and clean dirt and dust from fi ns. 2. Reinstall housing. Cleaning silencer and exhaust port (check periodically) 1. Carefully remove housing halves. 2. Remove and disassembl...

  • Page 19: Storage

    17 storage 6. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor. 7. Remove the spark plug and pour 1/2 tablespoon (1/4 oz) of fresh, clean, 2-stroke engine oil into the cylinder through the spark plug hole. A. Place a clean cloth over ...

  • Page 20: Specifications

    18 specifications edr-260 mass without drill bit kg 5.18 (11.42 lb) volume fuel tank l 0.58 (19.6 us fl . Oz.) drill size mm 32 - 178 (1.25 - 7 inch) chuck capacity mm 13 (0.5 inch) speed r/min 610 mission reduction ratio 17.1 (regular side) 19.0 (reverse side) lubrication grease external dimensions...

  • Page 21: Warranty Statements

    19 warranty statements echo limited warranty statement for product sold in usa and canada beginning 01/01/2010 echo's responsibility echo incorporated’s limited warranty, provides to the original purchaser that this echo product is free from defects in material and workmanship. Under normal use and ...

  • Page 22

    20 purchased repair parts, short blocks and accessories ‡gd\uhvlghqwldoruqrqlqfrphsurgxflqjzduudqw\ ‡gd\frpphufldolqvwlwxwlrqdodjulfxowxudolqgxvwuldolqfrphsurgxflqjruuhqwdodssolfdwlrqzduudqw\ attention two-stroke engine power product owners this echo two-stroke engine power product is a quality-engi...

  • Page 23: Product Registration

    21 thank you for choosing echo power equipment please go to http://www.Echo-usa.Com/warranty/register-your-echo to register your new product on-line. It’s fast and easy! Note: your information will never be sold or misused by echo, inc. Registering your purchase enables us to contact you in the unli...

  • Page 24

    22.