1. DL manuals
  2. Echo
  3. Trimmer
  4. GT-225
  5. Operator's Manual

Echo GT-225 Operator's Manual

Summary of GT-225

  • Page 1

    X7502257007 © 4/2016 echo inc. Operator’s manual specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include ...

  • Page 2

    Table of contents shc-225/s 2 x7502257007 © 4/2016 echo inc. Table of contents table of contents .............................................................................................. 2 introduction ................................................................................................

  • Page 3

    X7502257007 3 © 4/2016 echo inc. Shc-225/s introduction introduction welcome to the echo family. This echo product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the safety manual. You will find both easy to use and full of helpfu...

  • Page 4

    Safety shc-225/s 4 x7502257007 © 4/2016 echo inc. Echo consumer product support if you require assistance or have questions concerning the application, operation or maintenance of this product you may call the echo consumer product support department at 1-800-673-1558 from 8:00 am to 5:00 pm (centra...

  • Page 5

    X7502257007 5 © 4/2016 echo inc. Shc-225/s safety the safety alert symbol accompanied by the word “caution” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. The enclosed message provides information necessary for the protection of the unit. N...

  • Page 6

    Safety shc-225/s 6 x7502257007 © 4/2016 echo inc. Avoid all power lines. This unit is not insulated against electrical current. Plan retreat path from falling objects do not allow flames or sparks near fuel ignition on / off do not smoke near fuel primer bulb choke control “run” position (choke open...

  • Page 7

    X7502257007 7 © 4/2016 echo inc. Shc-225/s safety personal condition and safety equipment users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit. Physical c...

  • Page 8

    Safety shc-225/s 8 x7502257007 © 4/2016 echo inc. • pants should have long legs, shirts should have long sleeves. • do not wear shorts. • do not wear ties, scarves, jewelry, or clothing with loose or hanging items that could become entangled in moving parts or surrounding growth. • keep clothing but...

  • Page 9

    X7502257007 9 © 4/2016 echo inc. Shc-225/s safety • keep your body warm, especially the head, neck, feet, ankles, hands, and wrists. • maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking. • limit the hours of operation. Try to fil...

  • Page 10

    Safety shc-225/s 10 x7502257007 © 4/2016 echo inc. All over head electrical conductors and communications wires can have electricity flow with high voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly, otherwise serious injury or death may result....

  • Page 11

    X7502257007 11 © 4/2016 echo inc. Shc-225/s safety equipment use only echo attachments. Serious injury may result from the use of a non-approved attachment combination. Echo, inc. Will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and ap...

  • Page 12

    Emission control shc-225/s 12 x7502257007 © 4/2016 echo inc. Emission control (exhaust & evaporative) carb and epa emissions control information the emission control system for the engine is em (engine modification) and, if the second to last character of the engine family on the emission control in...

  • Page 13

    X7502257007 13 © 4/2016 echo inc. Shc-225/s description description locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your echo dealer. 1 2 3 4 5 6 8 10 9 7 9 ...

  • Page 14

    Description shc-225/s 14 x7502257007 © 4/2016 echo inc. 1. Power head - includes the engine, clutch, fuel system, ignition system and recoil starter. 2. Throttle handle - for right hand - contains stop switch, throttle lockout, and throttle trigger. 3. Throttle trigger lockout - this lever must be h...

  • Page 15

    X7502257007 15 © 4/2016 echo inc. Shc-225/s contents contents the echo product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or echo dealer...

  • Page 16

    Assembly shc-225/s 16 x7502257007 © 4/2016 echo inc. Assembly support handle note: label shows minimum spacing for support handle location 1. Position support handle in comfortable operating position and tighten screws. Operation moving parts can amputate fingers or cause severe injuries. Keep hands...

  • Page 17

    X7502257007 17 © 4/2016 echo inc. Shc-225/s operation fuel diesel fuels and alternative fuels, such as e-15 (15% ethanol), e-85 (85% ethanol) or any fuels not meeting echo requirements are not approved for use in echo 2-stroke gasoline engines. Use of diesel or alternative fuels may cause performanc...

  • Page 18

    Operation shc-225/s 18 x7502257007 © 4/2016 echo inc. ◆ fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. ◆ never refuel a unit when the engine is hot or running! ◆ do not fill fuel tanks indoors. Always fill fuel tanks outdoors over bare ground. ◆ ...

  • Page 19

    X7502257007 19 © 4/2016 echo inc. Shc-225/s operation stored two-stroke fuel may separate. Always shake fuel container thoroughly before each use. Starting cold engine hedge trimmer blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades whenever possible, and ...

  • Page 20

    Operation shc-225/s 20 x7502257007 © 4/2016 echo inc. 4. Recoil starter lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Firmly grasp throttle handle and throttle trigger lockout with left hand and fully depress throttle trigger to wide open position. Rapidly pul...

  • Page 21

    X7502257007 21 © 4/2016 echo inc. Shc-225/s operation 1. Stop switch move stop switch (a) away from the stop position. 2. Purge bulb pump purge bulb (c) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. 3. Recoil starter lay the unit on ...

  • Page 22

    Operation shc-225/s 22 x7502257007 © 4/2016 echo inc. If engine does not stop when stop switch is moved to stop position, close choke - cold start position - to stall engine. Have your echo dealer repair stop switch before using unit again. Hedge trimming engine exhaust is hot, and contains carbon m...

  • Page 23

    X7502257007 23 © 4/2016 echo inc. Shc-225/s maintenance maintenance moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before...

  • Page 24

    Maintenance shc-225/s 24 x7502257007 © 4/2016 echo inc. Important note - time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. Maintenance procedure notes: (1) apply lithium based grease every 25 hours of use. (2) inspect blade, and cl...

  • Page 25

    X7502257007 25 © 4/2016 echo inc. Shc-225/s maintenance 2. Remove air filter cover. Brush dirt from inside cover. 3. Replace filter if it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed. • lightly brush debris from filter. • soak heavily soiled filters in water/ deterge...

  • Page 26

    Maintenance shc-225/s 26 x7502257007 © 4/2016 echo inc. Use only ngk bpm-8y spark plug (bpmr-8y in canada) otherwise severe engine damage may occur. 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. Do not sand blast to clean....

  • Page 27

    X7502257007 27 © 4/2016 echo inc. Shc-225/s maintenance 1. Remove spark plug lead. 2. Remove air cleaner cover (a). 3. Remove engine cover (b). Do not use a metal scraper to remove dirt from the cylinder fins. 4. Use brush to remove dirt from the cylinder fins. 5. Remove ignition wires from clip for...

  • Page 28

    Maintenance shc-225/s 28 x7502257007 © 4/2016 echo inc. 1. Remove spark plug lead. 2. Remove engine cover (b). 3. Place piston at top dead center (tdc) to prevent carbon/dirt from entering cylinder. 4. Remove spark arrestor screen cover (c), gaskets (d), (e), and screen (f), from muffler body. 5. Cl...

  • Page 29

    X7502257007 29 © 4/2016 echo inc. Shc-225/s maintenance 4. Inspect heat shield, and replace if damaged. 5. Install heat shield and muffler. 6. Tighten muffler mounting bolts (or nuts) to 90-110 kgf•cm (80-95 in•lbf). 7. Install engine cover and attach spark plug lead. 8. Start engine, and warm to op...

  • Page 30

    Maintenance shc-225/s 30 x7502257007 © 4/2016 echo inc. 1. Check idle speed and reset if necessary. If a tachometer is available, idle speed screw (a) should be set to the specifications found on “specifications” page of this manual. Turn idle screw (a) clockwise to increase idle speed; counterclock...

  • Page 31

    X7502257007 31 © 4/2016 echo inc. Shc-225/s maintenance gear case level 1. 1. Clean dirt from the grease fitting (a). 2. Carefully pump grease into fitting (a). Do not force grease. Too much pressure will force grease past seals and cause damage. Apply 1 - 2 pumps of grease every 15 - 25 hours of op...

  • Page 32

    Maintenance shc-225/s 32 x7502257007 © 4/2016 echo inc. 2. Pull the drive shaft (c) from the housing, wipe clean and re-coat with a thin coating (15 ml [1/2 oz.]) of grease. 3. Slide the drive shaft back in the drive housing being careful not to get dirt on the flex shaft. 4. Install the gear housin...

  • Page 33

    X7502257007 33 © 4/2016 echo inc. Shc-225/s maintenance 1. Move stop switch to stop position. 2. Disconnect spark plug wire. 3. Remove blade guard, if installed (see “blade guard remove/ install instructions”). 4. Slide blades to allow file clearance using slots (a) on bottom of blade. Do not pry ag...

  • Page 34

    Maintenance shc-225/s 34 x7502257007 © 4/2016 echo inc. 1. Tighten blade screws (a) securely. 2. Hold blade screws (a) to prevent turning, and tighten lock nuts (b). Locking ability of hedge trimmer blade lock nuts will diminish each time they are removed. Replace if turning resistance is not felt w...

  • Page 35

    X7502257007 35 © 4/2016 echo inc. Shc-225/s troubleshooting troubleshooting engine problem troubleshooting chart problem check status cause remedy engine cranks - starts hard/ doesn’t start fuel at carburetor no fuel at carburetor fuel strainer clogged fuel line clogged carburetor clean or replace c...

  • Page 36

    Storage shc-225/s 36 x7502257007 © 4/2016 echo inc. Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. Storage the muffler and surrounding cover become h...

  • Page 37

    X7502257007 37 © 4/2016 echo inc. Shc-225/s storage hedge trimmer blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades whenever possible, and always wear gloves to protect hands. Do not store in enclosure where fuel fumes may accumulate or reach an open flam...

  • Page 38

    Specifications shc-225/s 38 x7502257007 © 4/2016 echo inc. Specifications model shc-225, shc-225s length (shc-225) 1758 mm (69.21 in.) length (shc-225s) 1480 mm (58.27 in.) width (shc-225) 246 mm (9.69 in.) width (shc-225s) 246 mm (9.69 in.) height (shc-225) 290 mm (11.4 in.) height (shc-225s) 290 m...

  • Page 39

    X7502257007 39 © 4/2016 echo inc. Shc-225/s specifications this spark ignition system complies with the canadian standard ices-002. Height 21mm (0.83 in.) maximum diameter cut soft material 25.4 mm (1 in.) woody material 13 mm (1/2 in.) idle speed 2,750 rpm clutch engagement speed 4,100 rpm wide ope...

  • Page 40

    Product registration shc-225/s 40 x7502257007 © 4/2016 echo inc. Product registration thank you for choosing echo power equipment please go to http://www.Echo-usa.Com/warranty/register-your-echo to register your new product on-line. It's fast and easy ! Note: your information will never be sold or m...

  • Page 41

    X7502257007 41 © 4/2016 echo inc. Shc-225/s product registration.

  • Page 42

    Notes shc-225/s 42 x7502257007 © 4/2016 echo inc. Notes.

  • Page 43

    X7502257007 43 © 4/2016 echo inc. Shc-225/s notes.

  • Page 44

    Echo, incorporated 400 oakwood road lake zurich, il 60047 www.Echo-usa.Com s85513001125/s85513999999 (s)s86213001061/s86213999999.