Echo HCA-2500 Service Data

Manual is about: Hedge Trimmer

Summary of HCA-2500

  • Page 1

    Hca-2500 15-23c-00 1 lntroduction we are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications, illustrations and directions in this service data are based on the latest products inf...

  • Page 2

    Service information hca-2500 2 1 service information 1-1 specifications dimensions length mm(in) 2330 (91.7) width mm(in) 225 (9.3) height mm(in) 225 (9.3) dry weight kg(lb) 6.4 (14.1) engine type kioritz, air-cooled, two-stroke, single cylinder rotation anticlockwise as viewed from the output end d...

  • Page 3

    Service information hca-2500 3 1-2 technical data engine idling speed r/min 2400 - 3200 operating speed r/min 7000 - 8000 wide open throttle speed r/min 9000 - 10500 clutch engagement speed r/min 3700 - 4300 compression pressure mpa (kgf/cm 2 ) (psi) 0.94 (9.6) (136) ignition system spark plug gap m...

  • Page 4

    Service information hca-2500 4 1-3 torque limits descriptions size kgf•cm n•m in•lbf starter pawl carrier m 8 80 - 100 8 - 10 70 - 85 system starter case m 4* 22 - 28 2.2 - 2.8 19 - 24 ignition ignition coil (cdi module) m 4* 38 - 55 3.8 - 5.5 35 - 50 system spark plug m 14 150 - 170 15 - 17 130 - 1...

  • Page 5

    Service information hca-2500 5 5k193 5k228 5k229 5k230 5k231 5k016 5k042 5k194 0 1 2 3 4 5 6 7 8 9 10 11 12 0 5 10 5k171 5k232 1-5 service limits a b c d e f g h k l description mm (in) a cylinder bore when plating is worn and aluminium can be seen b piston outer diameter min. 33.91 (1.335) c piston...

  • Page 6

    Service information hca-2500 6 a 20 20 40 40 60 60 80 80 120 120 140 140 160 160 18 0 180 20 20 100 100 91019 ignition air gap gauge #.014 = .35mm p/n 91004 key part number description used for: 1 897801-33330 tachometer pet-1000 measuring engine speed to adjust carburettor 2 363018-00310 washer ins...

  • Page 7

    Service information hca-2500 7 2 emission adjustment guide 2-1 general adjusting rules a. Before starting the unit for adjustment, check the following items. 1. The correct spark plug must be clean and properly gapped. 2. The air filter element must be clean and properly installed. 3. The muffler ex...

  • Page 8

    Service information hca-2500 8 3. Remove the limiter cap tool from the limiter cap turning the tool clockwise, leaving the limiter cap in place. 4. Screw threaded end of limiter cap tool 91019 into centre hole of the other limiter cap anticlockwise until the limiter cap is come out from the mixture ...

  • Page 9

    Service information hca-2500 9 2-3 adjusting carburettor 1. Start engine and warm it up alternating engine speed between wot and idle every 5 seconds for 1 minute. 2. Using 2.5 mm wide blade screw driver, adjust l mixture needle to obtain maximum idle speed. 3. Set idle speed in the range of 3,400 t...

  • Page 10

    Service information hca-2500 10 2-3 adjusting carburettor (continued) 8. After adjusting carburettor, put new limiter cap on the other side of limiter cap tool as shown, and press the limiter caps to the bottoms on l and h mixture needles respectively. Note : align the limiter cap’s tabs (a) with lo...