1. DL manuals
  2. Echo
  3. Saw
  4. Power Blend CSG-680
  5. Operator's Manual

Echo Power Blend CSG-680 Operator's Manual

Other manuals for Power Blend CSG-680: Specification Sheet

Summary of Power Blend CSG-680

  • Page 1

    Warning read the instructions carefully and follow the rules for safe operation. Failure to do so could result in serious injury. Warnung lesen sie die bedienungsanleitung sorgfältig durch und befolgen sie die sicherheitsbestimmungen, weil sonst das risiko schwerer verletzungen besteht. Avvertenza l...

  • Page 2: Introduction

    2 csg-680 specifications, descriptions and illustrations in this manual were accurate at the time of publication, and are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment. Warning improper use or care of this u...

  • Page 3: Symbols and Signs

    3 csg-680 symbols and signs decals f r o n t carefully read the operator’s manual. Wear eyes, ears, respiration and head protection. Locate this safety decal on your unit. The complete unit illustration found in the “description” section will help you locate them. Make sure the decal is legible and ...

  • Page 4: Description

    4 csg-680 description wheel shield wheel wheel mounting bolt outer flange wheel blotter rubber spark / dust shield fuel tank cap ignition switch throttle trigger throttle latch metal foot choke starter grip air cleaner cover nut front handle air cleaner cover throttle lockout rear handle idle speed ...

  • Page 5: Definition Of Terms

    5 csg-680 definition of terms ansi – american national standards institute. Arbor – a spindle or axle. Arbor hole – the mounting hole in the abrasive wheel. Autmatic belt tensioner – this feature, a spring- loaded device in the wheel arm, maintains belt tension. Blotters – discs of soft material pla...

  • Page 6: Operator Safety Precautions

    6 csg-680 read this cut-off saw operator’s manual carefully. Be sure you understand how to operate this saw properly before you use it. Establish a training program for cut-off saw operators. Use safety footwear, snug-fitting clothing and protective gloves. Wear eye, hearing and head protection devi...

  • Page 7

    7 csg-680 keep a firm grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle when the engine is running. Use a firm grip with thumbs and fingers encircling the saw handles. A firm grip will help you to keep control if the saw kickback toward you, or...

  • Page 8: Preparing For Use

    8 csg-680 spectators children and fellow workers must be warned to come no nearer than 9 m while the saw is in use. Shut off the saw immediately if some one moves closer to you than 9 m. Persons working in the area near you should wear the same protective equipment as the saw operator if endangered ...

  • Page 9

    9 csg-680 physical condition your judgment and / or dexterity may be impaired if you are ill or have taken alcohol or other substances known to affect the way you would function normally. Operate only when sound in mind and body. Warning precautions againt vibration and cold it is believed that a co...

  • Page 10

    10 csg-680 prim use general purpose mild and stainless steel: re-bar, pipe and structural steel ductile or cast iron and concrete lined pipe heat treated, wear hardened and alloyed steel all masonry, concrete and stone products and asphalt rock, block, stone, tile engine drive pully 9500 r/min ± 500...

  • Page 11

    11 csg-680 refer to chart wheel dimensions abrasive wheel: diamond wheel: wheel diameter 355 mm 355 mm mounting hole diameter 20 mm (22 mm with adapter) 20 mm (22 mm with adapter) wheel blotters and mounting flanges wheel blotters attached to both sides of reinforced wheels are cushions needed to eq...

  • Page 12

    12 csg-680 facts about abrasive wheel echo wheels are made by laying a strong fiber mesh material into a form, pouring a mixture of resin and the abrasive grit particles over the mesh, and adding a second layer of mesh over the mixture. Then the resin and reinforcing mesh are bonded together and cur...

  • Page 13

    13 csg-680 how to install the wheel insert the bar tool. Rotate the drive shaft until the hole in the large pulley and the bar tool aligned. Unscrew wheel mounting bolt with the 17 mm end of the box wrench or your fingers. Remove wheel bolt, washers and outer flange, leaving inner flange in place. M...

  • Page 14: Operation

    14 csg-680 set saw down on level ground with wheel or saw blade in the clear. Grasp front handle with left hand, and hold down rear handle with toe of your boot. Never “drop-start” the saw. Warning wheel will rotate when engine is started at latched throttle setting. Keep cutting wheel in the clear....

  • Page 15

    15 csg-680 1. Squeeze and release trigger to unlatch it and take control of the throttle. 2. Let engine warm to operating temperature before doing any cutting. 3. Take cutting stance on left side of saw. Never get any part of your body behind the saw. Hold the saw firmly with both hands. Throttle up...

  • Page 16

    16 csg-680 cutting technique the main objectives are to avoid overheating the wheel, and to prevent it from being pinched or trapped or stressed in any way. Z adjust position of wheel guard to direct the discharge away from you. Z prepare to make straight cuts only. Use a snap- line to mark long cut...

  • Page 17

    17 csg-680 troubleshooting cutting problems troubleshooting engine problems trouble wheel stops when cutting pressure is applied belt slips and cannot be tensioned properly poor cutting – wheel discoloured at outer area trouble engine will not start engine hard to start engine misses engine overheat...

  • Page 18: Maintenance and Adjustment

    18 csg-680 maintenance and adjustment rib ace-belt change and adjustment 1. Move ignition switch down “stop” position. 2. Remove belt tension (with 13 mm end of the box wrench) by turning the cam anticlockwise. 3. Remove rear arm cover and front arm cover. (save the seven screws.) 4. Use the 13 mm e...

  • Page 19

    19 csg-680 pleated main filter nylon mesh third filter foam first filter air cleaner base plate air filter air cleaner cover dust from cutting must be prevented from entering the engine. The three (3) filters in the air cleaner system can do this if they are properly maintained and correctly install...

  • Page 20

    20 csg-680 (check periodically) 1. Do not allow dust to enter fuel tank. 2. Clogged filter will cause difficulty in starting engine or abnormalities in engine performance. 3. Pull the fuel filter out through fuel inlet port with a piece of steel wire or the like. 4. When the filter is dirty, replace...

  • Page 21

    21 csg-680 every unit is run at the factory and the carburettor is set in compliance with emission regulations. In addition, the carburettor is equipped with “h” (high speed needle) and “l” (low speed needle) needle adjustment limiters that prevent settings outside acceptable limits. 1. Before adjus...

  • Page 22

    22 csg-680 clean muffler and cooling system the dust created in cutting is drawn into the cooling system by the rotor fan. It can cover the cooling fins and clog the air passages. Unless the system is cleaned in time, the engine will run too hot. Whenever cleaning the cooling system, take advantage ...

  • Page 23: Storage After Use

    23 csg-680 storage after use z inspect and adjust every part of the cut-off saw. - completely clean every part and repair if necessary. - apply thin coating of oil on metal parts to prevent rust. Z remove cutting wheel. Z drain fuel tank, pull starter slowly a few times to drain fuel from carburetto...

  • Page 24: Specifications

    24 csg-680 specifications * technical data subject to change without notice. External dimentions : without cutting wheel length × width × height mm 740 × 250 × 385 mass : without cutting wheel and empty tank kg 11.5 volume : fuel tank ml (cm³) 640 fuel ( mixture ratio ) regular grade petrol. Minimum...

  • Page 25

    25 csg-680 gb declaration “ce” of conformity the undersigned manufacturer: kioritz corporation 7-2 suehirocho 1-chome ohme ; tokyo 198-8711 japan declares that the hereunder specified new unit: engine cut-off saw brand : echo type : csg-680 complies with: *the requirements of machinery directive 98/...

  • Page 26

    X750-006 93 4 x750410-420 5 gb © 2004 7-2 suehirocho 1-chome, ohme, tokyo 198-8711, japan phone: 81-428-32-6118. Fax: 81-428-32-6145..