1. DL manuals
  2. Echo
  3. Brush Cutter
  4. SMR-2110 - 01-99
  5. Operator's Manual

Echo SMR-2110 - 01-99 Operator's Manual

Summary of SMR-2110 - 01-99

  • Page 1

    Grass trimmer/brush cutter operator's manual models, srm - 2100, 2110 serial number 001001 & up models, type 1e srm - 2100, 2110 serial number 001001 - 982332 x7532278901 89861554131 01/99 warning danger read rules for safe operation and instructions carefully. Echo provides an operator's manual and...

  • Page 3

    G rass t rimmer /b rush c utter o perator ' s m anual 3 the circle with the slash symbol means whatever is shown within the circle is prohibited. Important the enclosed message provides information necessary for the protection of the unit. Note this enclosed message provides tips for use, care and m...

  • Page 4: Warning

    4 shaft decal warning danger • this unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the operator's and safety manuals. • blindness can occur from objects that are thrown or ricocheted even with shield i...

  • Page 5

    G rass t rimmer /b rush c utter o perator ' s m anual 5 s afety i nstructions personal condition and safety equipment warning danger trimmer/brush cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and or safety precautions are not followed. Proper cloth...

  • Page 6

    6 repetitive stress injuries it is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a repetitive str...

  • Page 7

    G rass t rimmer /b rush c utter o perator ' s m anual 7 safe operation warning danger do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. • provide all operators of this equipment with the operato...

  • Page 8

    8 contents list items 1 - power head 1 - drive shaft assembly 1 - plastic bag (co-pack) - 1, operator's manual - 1, safety manual - 1, warranty registration card - 1, limited warranty statement - 1, plastic shield - 1, tool bag --1, 8mm x 10mm wrench --1, scrench --1, locking tool - 1, nylon trimmer...

  • Page 9

    G rass t rimmer /b rush c utter o perator ' s m anual 9 1 safety video 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26 5 21 22 23 24 25.

  • Page 10

    10 1. Operator's manual - included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.E., operation, maintenance, storage and specifications. 2. Safety manual - included in plastic bag (co-pack). Read before operation and keep in a safe place for future ...

  • Page 11

    G rass t rimmer /b rush c utter o perator ' s m anual 11 s pecifications srm-2100, 2110 1/1e l e d o m e 1 / 1 0 0 1 2 e 1 / 1 0 1 1 2 h t g n e l ) . N i 9 5 ( m m 0 0 5 1 ) . N i 9 5 ( m m 0 0 5 1 h t d i w ) . N i 0 . 3 1 ( m m 0 3 3 ) . N i 6 . 3 2 ( m m 0 0 6 t h g i e h ) . N i 8 . 1 1 ( m m 0...

  • Page 12

    12 plastic shield installation (for nylon line operation) tools required: screwdriver. Parts required: plastic shield, shield plate, three (3) 5mm x 15mm screws. Note the plastic shield is for use with the nylon line head only. Install metal shield when using plastic or metal blades. 1. (srm-2110) r...

  • Page 13

    G rass t rimmer /b rush c utter o perator ' s m anual 13 blade installation all models. Important if non-standard monofilament head, metal/plastic blade or cultivator etc. Is used, the carburetor must be re-set or serious engine damage may occur. See "carburetor adjustment" pages 27 - 28 and "specif...

  • Page 14

    14 install harness clamp note some models require installation of harness clamp. If your unit does not have a clamp, follow these directions. Tools required: screwdriver, 8mm x 10mm open end wrench. Parts required: clamp, 4mm x 18mm hexagon head, bolt, link. 6. Remove shield and gear housing as an a...

  • Page 15

    G rass t rimmer /b rush c utter o perator ' s m anual 15 throttle linkage and ignition leads tools required: 8mm x 10mm open end wrench (all models), 3mm allen wrench. 1. Close choke and remove air filter cover. 2. Loosen nut (a) and place threaded end of throttle linkage in bracket slot. Finger tig...

  • Page 16

    16 u - handle installation tools required: 8mm x 10mm open end wrench, slotted screwdriver, (3mm hex wrench srm-2100 only.) parts required: u-handle kit. (srm-2100) p/n 35130454130 note on model srm-2110 use steps 1, 10, 11, and 13 - 17 only. 1. Close choke and remove air filter cover. 2. Disconnect...

  • Page 17

    G rass t rimmer /b rush c utter o perator ' s m anual 17 11. Secure throttle linkage and leads to drive shaft with cable clips supplied. 12. Install power head and align gear box, power head and u-handles. Tighten all screws. 13. Place throttle linkage in slot in bracket with one nut (a) and washer ...

  • Page 18: - O

    18 warning danger the type of blade used must be matched to the type and size of material cut. An improper or dull blade can cause serious personal injury. Blades must be sharp. Dull blades increase the chance of kick out and injury to yourself and bystanders. Plastic and nylon blades require "blade...

  • Page 19

    G rass t rimmer /b rush c utter o perator ' s m anual 19 8 tooth weed/grass blade p/n 69600120331 is designed for grass, garden debris and thick weeds. Do not use this blade for brush or heavy woody growth, 3/4" in. (19 mm) diameter or larger. Brush/clearing blade p/n 69500120331is designed for cutt...

  • Page 20

    20 fuel fuel requirements gasoline - use 89 octane [ ] gasoline or gasohol known to be good quality. Gasohol may contain up to 10% ethyl (grain) alcohol or 15% mtbe (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is not approved. Two stroke oil - a two-stroke engine oil meeti...

  • Page 21

    G rass t rimmer /b rush c utter o perator ' s m anual 21 o peration starting cold engine warning danger the cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "carburetor adjustment" instructions in this manual or see your echo dealer, otherwise ser...

  • Page 22

    22 starting warm engine the starting procedure is the same as cold start except do not close the choke. Warning danger the cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "carburetor adjustment" instructions in this manual or see your echo dealer...

  • Page 23

    G rass t rimmer /b rush c utter o perator ' s m anual 23 maintenance intervals / t n e n o p m o c m e t s y s e c n a n e t n i a m e r u d e c o r p d ' q e r l l i k s l e v e l r o y l i a d e r o f e b e s u y r e v e l e u f e r 3 s h t n o m 0 9 r o s r u o h 6 s h t n o m 0 7 2 r o s r u o h...

  • Page 24

    24 air filter level 1. Tools required: cleaning brush parts required: 90008 repower air & fuel filter kit. 1. Close choke (cold start position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu- lated dirt from the air cleaner area. 2. Remove the ai...

  • Page 25

    G rass t rimmer /b rush c utter o perator ' s m anual 25 spark plug level 2. Tools required: scrench (combination socket wrench and screw driver supplied with unit), feeler gauge (preferably a wire gauge), soft metal brush parts required: spark plug ngk bpm-7a 1. Remove spark plug and check for foul...

  • Page 26

    26 note the throttle linkage remains assembled to the cover and the spark plug lead and grommet remain installed. 3. Use the wooden stick or brush to remove dirt form cylinder fins. 4. Remove grass and leaves from the grid between the recoil starter and fuel tank. 5. Assemble components in reverse o...

  • Page 27

    G rass t rimmer /b rush c utter o perator ' s m anual 27 carburetor adjustment type 1e emission models level 2. Tools required: slotted screwdriver w/2 mm blade width, tachometer (echo p/n 99051130017) parts required: none. Note every unit is run at the factory and the carburetor is set in complianc...

  • Page 28

    28 carburetor adjustment type 1 non emission models idle speed adjustment note if carburetor has limiter caps follow "carburetor adjustment" procedures for type 1e models on previous page. Turn "idle" speed adjustment screw (c) cw (clockwise) until cutting attachment begins to turn, then turn screw ...

  • Page 29

    G rass t rimmer /b rush c utter o perator ' s m anual 29 a b b c lubrication level 1. Tools required: 8 mm open end wrench, cross head screwdriver, clean rag parts required: echo ® lube tm 8 oz. (p/n 91014) or lithium base grease. Gear housing 1. Clean all loose debris from gear box. 2. Remove plug ...

  • Page 30

    30 a b d c e d g e b h f a b 1. Hold drum (a) and turn spool (b) cw (clockwise) until it stops. Pull spool from drum. Do not push in on spool when turning. 2. Use one piece of new nylon line (c) 40 ft. (12m) long and thread through the molded loop (d) on the spool. Pull line tight and adjust so one ...

  • Page 31

    G rass t rimmer /b rush c utter o perator ' s m anual 31 sharpening metal blades three styles of metal blades are approved for use on the echo brush cutter. The 8-tooth blade can be sharpened during normal mainte- nance. The clearing blade and 80 tooth blade require professional service. Before shar...

  • Page 32

    32 t roubleshooting engine problem troubleshooting chart problem check status cause remedy engine cranks - starts hard/ doesn't start fuel at carburetor no fuel at carburetor fuel strainer clogged fuel line clogged carburetor clean or replace clean or replace see your echo dealer fuel at cylinder no...

  • Page 33: Warning

    G rass t rimmer /b rush c utter o perator ' s m anual 33 2. Place the stop switch in the "off" position. 3. Remove accumulation of grease, oil, dirt, and debris from exterior of unit. 4. Perform all periodic lubrication and services that are required. 5. Tighten all the screws and nuts. 6. Drain the...

  • Page 34

    S ervicing i nformation parts genuine echo parts and echo re power parts and assemblies for your echo products are available only from an authorized echo dealer. When you do need to buy parts always have the model number, type number and serial number of the unit with you. You can find all three num...

  • Page 35

    1 models: serial number manual numbers modelo: nÚmeros de serie numero de pieza srm-2100 982333 & up x7532278901 / 89861554131 srm-2110 n/a x7532278901 / 89861554131 supplement to operator's manual suplemento del manual del operador this supplement contains important information. Please keep with yo...

  • Page 36

    2 d warning danger inspect starting area for hazards such as rocks, glass, debris etc. Which could be contacted by the cutting attachment when starting. Keep helpers and bystanders at least 15 m (50 ft.) from starting area, other- wise serious personal injury may result. 4. Lay the pruner on a flat ...