1. DL manuals
  2. Echo
  3. Brush Cutter
  4. SRM-210 - 12-03 SERIAL NUMBER 05295101-05999999
  5. Operator's Manual

Echo SRM-210 - 12-03 SERIAL NUMBER 05295101-05999999 Operator's Manual

Summary of SRM-210 - 12-03 SERIAL NUMBER 05295101-05999999

  • Page 1

    Grass trimmer/brush cutter operator's manual model srm-210 serial number 05295101 - 05999999 warning danger read rules for safe operation and instructions carefully. Echo provides an operator's manual and a safety manual. Both must be read and understood for proper and safe operation. X7702275402 x7...

  • Page 2: ’

    2 t able of c ontents introduction ........................................................................ 2 - the operator's manual ............................................... 2 - the safety manual ....................................................... 2 manual safety symbols and important in...

  • Page 3

    G rass t rimmer /b rush c utter o perator ' s m anual 3 important the enclosed message provides information necessary for the protec- tion of the unit. Note this enclosed message provides tips for use, care and maintenance of the unit. This symbol accompanied by the words warning and danger calls at...

  • Page 4

    4 shaft decal warning danger • this unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the operator's and safety manuals. • blindness can occur from objects that are thrown or ricocheted even with shield i...

  • Page 5

    G rass t rimmer /b rush c utter o perator ' s m anual 5 s afety i nstructions personal condition and safety equipment warning danger users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear m...

  • Page 6

    6 equipment warning danger use only echo approved attachments. Serious injury may result from the use of a non-approved attachment combination. Echo, inc. Will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by echo. Read and ...

  • Page 7

    G rass t rimmer /b rush c utter o perator ' s m anual 7 important engine information engine family: 3ehxs.0214ea displacement: 21.2 cc emission compliance period: 300 hours this engine meets u.S. Epa ph2 emission regula- tions for small nonroad engine. Refer to owner's manual for maintenance specifi...

  • Page 8

    8 d escription the echo product you purchased has been partially assembled for your convenience. Due to packaging restrictions, installation of the plastic debris shield, nylon line head, and positioning of the front handle may be necessary. After opening the carton, check for damage. Immediately no...

  • Page 9

    G rass t rimmer /b rush c utter o perator ' s m anual 9 12 18 safety video 20 11 13 14 15 16 17 19 1 2 5 6 7 8 9 10 4 3.

  • Page 10

    10 1. Power head - includes the engine, clutch, fuel system, ignition system and recoil starter. 2. Grip - rear (right hand) handle. 3. Throttle trigger lockout - this lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged....

  • Page 11

    G rass t rimmer /b rush c utter o perator ' s m anual 11 s pecifications * install and use u-handle when operating any model with blade. Model ----------------------------------------------------- srm-210 length ------------------------------------------------------- 1770 mm (69.7 in.) width -------...

  • Page 12

    12 tools required: screwdriver, head locking tool, 17x19mm t-wrench parts required: plastic shield, shield plate, three (3) 5mm x 16mm screws, nylon line head plastic shield installation (for nylon line operation) note the plastic shield is for use with the nylon line head only. Install metal shield...

  • Page 13: - O

    G rass t rimmer /b rush c utter o perator ' s m anual 13 front handle installation 1. Position front handle for comfortable operation and secure screws. P re - o peration operation with blades preparing the trimmer/brush cutter for blade use warning danger blade use demands specific brush cutter con...

  • Page 14

    14 choosing the correct blade warning danger the type of blade used must be matched to the type and size of material cut. An improper or dull blade can cause serious personal injury. Blades must be sharp. Dull blades increase the chance of kick out and injury to yourself and bystanders. Plastic/nylo...

  • Page 15

    G rass t rimmer /b rush c utter o perator ' s m anual 15 80 tooth brush blade(p/n 69500120331) is designed for cutting brush and woody growth up to 64 mm (2-1/2 in.) diameter. 22 tooth clearing blade (99944200130) is designed for dense thickets and saplings up to 64 mm (2-1/2 in.) diameter. Use shou...

  • Page 16

    16 important spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your echo dealer for ordering information. After refueling • wipe any spilled fuel from the unit. • move at least 3 m (10 ft.)...

  • Page 17

    G rass t rimmer /b rush c utter o perator ' s m anual 17 o peration starting cold engine warning danger the attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from ob...

  • Page 18

    18 starting warm engine the starting procedure is the same as cold start except do not close the choke, and do not depress throttle trigger to wide open position. Warning danger the attachment should not move at idle, otherwise serious personal injury may result. Note if attachment moves, readjust c...

  • Page 19

    G rass t rimmer /b rush c utter o perator ' s m anual 19 a stopping engine 1. Throttle release throttle and allow engine to return to idle before shutting off engine. 2. Stop switch move stop switch button (a) backward to stop position. Warning danger if engine does not stop when stop switch is move...

  • Page 20

    20 maintenance intervals / t n e n o p m o c m e t s y s e c n a n e t n i a m e r u d e c o r p d ' q e r l l i k s l e v e l r o y l i a d e r o f e b e s u y r e v e l e u f e r 3 s h t n o m 0 9 r o s r u o h 6 s h t n o m 0 7 2 r o s r u o h y l r a e y 0 0 6 s r u o h s e r u d e c o r p e c n...

  • Page 21

    G rass t rimmer /b rush c utter o perator ' s m anual 21 air filter level 1. Tools required: 25 - 50 mm (1 - 2 in.) cleaning brush parts required: 90008 repower tm air & fuel filter kit. 1. Close choke (cold start position [ ]). This prevents dirt from entering the carburetor throat when the air fil...

  • Page 22

    22 spark plug level 2. Tools required: t-wrench, feeler gauge, soft metal brush parts required: repower tm tune-up kit p/n 90074 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. Do not sand blast to clean. Remaining sand will...

  • Page 23

    G rass t rimmer /b rush c utter o perator ' s m anual 23 1. Disconnect spark plug lead from spark plug. 2. Remove (1) screw from top guard (a), and remove guard. 3. Remove (3) screws from engine cover (b), and remove cover. 4. Use the brush to remove dirt form cylinder fins. 5. Remove grass and leav...

  • Page 24

    24 1. Remove engine cover. See “cleaning cooling system” page 23 for instructions. 2. Remove spark arrestor screen cover (a), gasket (b), and screen (c) from muffler body. 3. Clean carbon deposits from muffler components. 4. Replace screen if it is cracked, plugged or has holes burned through. 5. Re...

  • Page 25

    G rass t rimmer /b rush c utter o perator ' s m anual 25 carburetor adjustment engine break-in new engines must be operated for a minimum of two tanks of fuel before carburetor adjustments can be made. During the break-in period, your engine performance will increase and exhaust emissions will stabi...

  • Page 26

    26 lubrication level 1. Tools required: 8 mm open end wrench, cross head screwdriver, clean rag parts required: echo ® lube tm 8 oz. (p/n 91014) or lithium base grease. Gear housing 1. Clean all loose debris from gear box. 2. Remove plug (a) and check level of grease. 3. Add grease if necessary, do ...

  • Page 27

    G rass t rimmer /b rush c utter o perator ' s m anual 27 nylon line replacement level 1. Parts required: echo 0.095" nylon trimmer line 6 m (20 ft.) long. 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (a) and firmly turn spool (b) cw (clockwise) until it disengages f...

  • Page 28

    28 8. Hold drum (a) firmly and turn spool (b) ccw (counterclockwise) until it stops. Do not push in on spool when turning. 9. Pull both lines out and trim to cut-off knife length. Sharpening metal blades three styles of metal blades are approved for use on the echo brush cutter. The 8-tooth blade ca...

  • Page 29

    G rass t rimmer /b rush c utter o perator ' s m anual 29 t roubleshooting t r a h c g n i t o o h s e l b u o r t m e l b o r p e n i g n e m e l b o r p k c e h c s u t a t s e s u a c y d e m e r s k n a r c e n i g n e - / d r a h s t r a t s t' n s e o d t r a t s r o t e r u b r a c t a l e u f...

  • Page 30

    30 s torage warning danger during operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long term storage (over 30 days) d...

  • Page 31: Notes

    G rass t rimmer /b rush c utter o perator ' s m anual 31 notes.

  • Page 32

    Echo, incorporated 400 o akwood r oad l ake z urich , il 60047 www.Echo-usa.Com available parts catalog srm-210 serial number 05001001 - 05999999 part number 99922203252 s ervicing i nformation parts genuine echo parts and echo repower™ parts and assemblies for your echo products are available only ...