1. DL manuals
  2. Echo
  3. Trimmer
  4. SRM-2110 TYPE 1E - PARTS CATALOG SERIAL NUMBER 001001
  5. Operator's Manual

Echo SRM-2110 TYPE 1E - PARTS CATALOG SERIAL NUMBER 001001 Operator's Manual

Other manuals for SRM-2110 TYPE 1E - PARTS CATALOG SERIAL NUMBER 001001: Parts Catalog, Operator's Manual
Manual is about: Echo Grass Trimmer/Brush Cutter Operator's Manual

Summary of SRM-2110 TYPE 1E - PARTS CATALOG SERIAL NUMBER 001001

  • Page 1

    Grass trimmer/brush cutter operator's manual models, type 1e srm - 2100, 2110 serial number 982333 & up x7532278902 89861554132 11/01 warning danger read rules for safe operation and instructions carefully. Echo provides an operator's manual and a safety manual. Both must be read and understood for ...

  • Page 3

    G rass t rimmer /b rush c utter o perator ' s m anual 3 the circle with the slash symbol means whatever is shown within the circle is prohibited. Important the enclosed message provides information necessary for the protection of the unit. Note this enclosed message provides tips for use, care and m...

  • Page 4: Warning

    4 shaft decal warning danger • this unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the operator's and safety manuals. • blindness can occur from objects that are thrown or ricocheted even with shield i...

  • Page 5

    G rass t rimmer /b rush c utter o perator ' s m anual 5 s afety i nstructions personal condition and safety equipment warning danger trimmer/brush cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and or safety precautions are not followed. Proper cloth...

  • Page 6

    6 repetitive stress injuries it is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a repetitive str...

  • Page 7

    G rass t rimmer /b rush c utter o perator ' s m anual 7 safe operation warning danger do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. • provide all operators of this equipment with the operato...

  • Page 8

    8 contents list items 1 - power head 1 - drive shaft assembly 1 - plastic bag (co-pack) - 1, operator's manual - 1, safety manual - 1, warranty registration card - 1, limited warranty statement - 1, plastic shield - 1, plastic shield hardware --1, shield plate --3, 5mm x 15mm screws (shield mtg.) - ...

  • Page 9

    G rass t rimmer /b rush c utter o perator ' s m anual 9 safety video 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 25 4 22 21 23 24 20 4.

  • Page 10

    10 1. Power head - includes the engine, clutch, fuel system, ignition system and recoil starter. 2. Grip - rear (right hand) handle. 3. Throttle trigger lockout - this lever must be held down during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is dep...

  • Page 11

    G rass t rimmer /b rush c utter o perator ' s m anual 11 s pecifications * install and use u-handle when operating any model with blade. L e d o m 0 0 1 2 - m r s 0 1 1 2 - m r s h t g n e l ) . N i 9 5 ( m m 0 0 5 1 h t d i w ) . N i 0 . 3 1 ( m m 0 3 3 ) . N i 6 . 3 2 ( m m 0 0 6 t h g i e h ) . N...

  • Page 12

    12 plastic shield installation (for nylon line operation) tools required: screwdriver. Parts required: plastic shield, shield plate, three (3) 5mm x 15mm screws. Note the plastic shield is for use with the nylon line head only. Install metal shield when using plastic or metal blades. 1. Remove plast...

  • Page 13

    G rass t rimmer /b rush c utter o perator ' s m anual 13 blade installation all models. Important if non-standard monofilament head, metal/plastic blade or cultivator etc. Is used, the carburetor must be re-set or serious engine damage may occur. See "carburetor adjustment" page 27 and "specificatio...

  • Page 14

    14 install harness clamp note some models require installation of harness clamp. If your unit does not have a clamp, follow these directions. Tools required: screwdriver, 8mm x 10mm open end wrench. Parts required: clamp, 4mm x 18mm hexagon head, bolt, link. 6. Remove shield and gear housing as an a...

  • Page 15

    G rass t rimmer /b rush c utter o perator ' s m anual 15 throttle linkage and ignition leads tools required: 8mm x 10mm open end wrench (all models), 3mm allen wrench. 1. Close choke and remove air filter cover. 2. Loosen nut (a) and place threaded end of throttle linkage in bracket slot. Finger tig...

  • Page 16

    16 g e d f u - handle installation tools required: 8mm x 10mm open end wrench, slotted screwdriver, (3mm hex wrench srm-2100 only.) parts required: u-handle kit. (srm-2100) p/n 35130454130 note on model srm-2110 use steps 1, 10, 11, and 13 - 17 only. 1. Close choke and remove air filter cover. 2. Di...

  • Page 17

    G rass t rimmer /b rush c utter o perator ' s m anual 17 11. Secure throttle linkage and leads to drive shaft with cable clips supplied. 12. Install power head and align gear box, power head and u-handles. Tighten all screws. 13. Place throttle linkage in slot in bracket with one nut (a) and washer ...

  • Page 18: - O

    18 choosing the correct blade warning danger the type of blade used must be matched to the type and size of material cut. An improper or dull blade can cause serious personal injury. Blades must be sharp. Dull blades increase the chance of kick out and injury to yourself and bystanders. Plastic and ...

  • Page 19

    G rass t rimmer /b rush c utter o perator ' s m anual 19 plastic/nylon blades may be used where ever the nylon line head is used. Do not use this blade for heavy weeds or brush! 8 tooth weed/grass blade p/n 69600120331 is designed for grass, garden debris and thick weeds. Do not use this blade for b...

  • Page 20

    20 fuel fuel requirements gasoline - use 89 octane [ ] gasoline or gasohol known to be good quality. Gasohol may contain up to 10% ethyl (grain) alcohol or 15% mtbe (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is not approved. Two stroke oil - a two-stroke engine oil meeti...

  • Page 21: Warning

    G rass t rimmer /b rush c utter o perator ' s m anual 21 o peration starting cold engine warning danger the cutting attachment should not move at idle. If cutting attach- ment moves, readjust carburetor according to "carburetor adjust- ment" instructions in this manual or see your echo dealer, other...

  • Page 22: Warning

    22 a starting warm engine the starting procedure is the same as cold start except do not close the choke. Warning danger the cutting attachment should not move at idle. If cutting attach- ment moves, readjust carburetor according to "carburetor adjust- ment" instructions in this manual or see your e...

  • Page 23

    G rass t rimmer /b rush c utter o perator ' s m anual 2 3 m aintenance your echo unit is designed to provide many hours of trouble-free service. Regular scheduled maintenance will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take y...

  • Page 24

    24 air filter level 1. Tools required: cleaning brush parts required: 90008 repower air & fuel filter kit. 1. Close choke (cold start position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu- lated dirt from the air cleaner area. 2. Remove the ai...

  • Page 25

    G rass t rimmer /b rush c utter o perator ' s m anual 25 spark plug level 2. Tools required: scrench (combination socket wrench and screw driver supplied with unit), feeler gauge (preferably a wire gauge), soft metal brush parts required: spark plug ngk bpm-7a 1. Remove spark plug and check for foul...

  • Page 26

    26 exhaust system spark arrestor screen level 2. Tools required: cross-head screwdriver, soft metal brush, wooden carbon scraper. Parts required: screen p/n 14586240630, gasket lid p/n 14586642031 1. Remove engine cover (a). See “cleaning cooling system” pages 25 & 26 for step by step instructions. ...

  • Page 27

    G rass t rimmer /b rush c utter o perator ' s m anual 27 carburetor adjustment emission models level 2. Tools required: slotted screwdriver w/2 mm blade width, tachometer (echo p/n 99051130017) parts required: none. Note every unit is run at the factory and the carburetor is set in compliance with e...

  • Page 28

    28 lubrication level 1. Tools required: 8 mm open end wrench, cross head screwdriver, clean rag parts required: echo ® lube tm 8 oz. (p/n 91014) or lithium base grease. Gear housing 1. Clean all loose debris from gear box. 2. Remove plug (a) and check level of grease. 3. Add grease if necessary, do ...

  • Page 29

    G rass t rimmer /b rush c utter o perator ' s m anual 29 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (a) and turn spool (b) cw (clockwise) until it stops. Pull spool from drum. Do not push in on spool when turning. 3. Use one piece of new nylon line (c) 6m (20 ft.)...

  • Page 30

    30 sharpening metal blades three styles of metal blades are approved for use on the echo brush cutter. The 8-tooth blade can be sharpened during normal mainte- nance. The clearing blade and 80 tooth blade require professional service. Before sharpening, closely inspect blade for cracks (look at the ...

  • Page 31

    G rass t rimmer /b rush c utter o perator ' s m anual 31 t roubleshooting warning danger fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open spark plug opening, otherwise serious personal injury may result. T r a h c g n i t o o h s e l...

  • Page 32: Warning

    32 2. Place the stop switch in the "off" position. 3. Remove accumulation of grease, oil, dirt, and debris from exterior of unit. 4. Perform all periodic lubrication and services that are required. 5. Tighten all the screws and nuts. 6. Drain the fuel tank completely and pull the recoil starter hand...

  • Page 33: Notes

    G rass t rimmer /b rush c utter o perator ' s m anual 33 notes.

  • Page 34: Notes

    34 notes.

  • Page 35: Notes

    G rass t rimmer /b rush c utter o perator ' s m anual 35 notes.

  • Page 36

    S ervicing i nformation parts genuine echo parts and echo re power parts and assemblies for your echo products are available only from an authorized echo dealer. When you do need to buy parts always have the model number, type number and serial number of the unit with you. You can find all three num...

  • Page 37

    Suplemento del manual del operador nÚmero de pieza x7532278902 (89861554132) para los modelo: srm-2100 s/n 991201 y superior, srm-2110 s/n 510001 y superior utilice por favor este suplemento manual del operador al ensamblar y manteniendo su srm-2100 - srm-2110 1 d escription page 7 emission control ...