1. DL manuals
  2. Echo
  3. Brush Cutter
  4. SRM-230 - 12-08
  5. Operator's Manual

Echo SRM-230 - 12-08 Operator's Manual

Summary of SRM-230 - 12-08

  • Page 1

    Warning read rules for safe operation and instructions carefully. Echo provides an operator's manual and a safety manual. Both must be read and understood for proper and safe operation. Grass trimmer/brush cutter operator's manual model srm - 230 srm - 230s x7532098302 x753002992 12/08.

  • Page 2

    2 copyright© 2008 by echo, incorporated all rights reserved. I ntroduction welcome to the echo family. This echo product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the safety manual you found in the same package. You will find...

  • Page 3

    G rass t rimmer /b rush c utter o perator ' s m anual 3 international symbols throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what th...

  • Page 4

    4 physical condition your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye protection wear eye protection that meets ansi z87.1 or ce requi...

  • Page 5

    G rass t rimmer /b rush c utter o perator ' s m anual 5 danger do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the manuals • provide all users of this equipment with the operator’s manual...

  • Page 6

    6 equipment warning use only echo approved attachments. Serious injury may result from the use of a non-approved attachment combination. Echo, inc. Will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by echo. Read and comply ...

  • Page 7

    G rass t rimmer /b rush c utter o perator ' s m anual 7 11 13 14 15 16 17 18 12 19 1 2 3 4 5 6 7 8 9 10 p/n x505002310 hot decal (near muffler) p/n 89016054130 d escription locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions o...

  • Page 8

    8 1. Power head - includes the engine, clutch, fuel system, ignition system and recoil starter. 2. Grip - rear (right hand) handle. 3. Throttle trigger lockout - this lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. ...

  • Page 9

    G rass t rimmer /b rush c utter o perator ' s m anual 9 c ontents the echo product you purchased has been partially assembled for your convenience. Due to packaging restrictions, installation of the plastic debris shield, nylon line head, and positioning of the front handle are necessary. After open...

  • Page 10

    10 a c nylon line head installation tools required: head locking tool. Parts required: nylon line head. Caution wear gloves or personal injury may result: • cutoff knife is sharp. • gearcase and surrounding area may be hot. 1. Be sure adapter plate (c) remains on pto shaft. 2. Align locking hole in ...

  • Page 11

    G rass t rimmer /b rush c utter o perator ' s m anual 11 min spacing front handle adjustment note label shows minimum spacing for front handle location. 1. Position front handle for comfortable operation and secure screws. O peration warning moving parts can amputate fingers or cause severe injuries...

  • Page 12

    12 srm/pas/sb blade set-up guide* to use these blades pro maxi-cut grass/weed plastic cutters rigid plastic tri-cut grass/weed blade metal tri-cut/8 tooth grass/weed blade metal 80t brush blade metal 22t clearing saw blade handle loop handle, w/or w/o barrier bar loop handle w/barrier bar, or u-hand...

  • Page 13

    G rass t rimmer /b rush c utter o perator ' s m anual 13 choosing the correct blade warning the type of blade used must be matched to the type and size of material cut. An improper or dull blade can cause serious personal injury. Blades must be sharp. Dull blades increase the chance of kick-out and ...

  • Page 14

    14 fuel notice: use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the storage section of this manual. Warning alternative fuels, such as e-20 (2...

  • Page 15

    G rass t rimmer /b rush c utter o perator ' s m anual 15 mixing instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close ...

  • Page 16

    16 starting cold engine warning the attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown. 1. Stop switch move stop sw...

  • Page 17

    G rass t rimmer /b rush c utter o perator ' s m anual 17 starting warm engine the starting procedure is the same as cold start except do not close the choke, and do not hold throttle trigger fully depressed. Warning the attachment should not move at idle, otherwise serious personal injury may result...

  • Page 18

    18 warning moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing uni...

  • Page 19

    G rass t rimmer /b rush c utter o perator ' s m anual 19 air filter level 1. Tools required: cleaning brush 25 or 50 mm (1 or 2 in.) parts required: repower tm air & fuel filter kit. 1. Close choke (cold start position [ ]). This prevents dirt from entering the carburetor throat when the air filter ...

  • Page 20

    20 spark plug level 2. Tools required: t-wrench, feeler gauge, soft metal brush. Parts required: repower tm tune-up kit important use only ngk bpm-8y spark plug (bpmr-8y in canada) otherwise severe engine damage may occur. 1. Remove spark plug and check for fouling, worn and rounded center electrode...

  • Page 21

    G rass t rimmer /b rush c utter o perator ' s m anual 21 1. Remove spark plug lead. 2. Remove two (2) muffler cover screws and muffler cover (a). 3. Remove screw and top guard (b). 4. Remove engine cover (c). Important do not use a metal scraper to remove dirt from the cylinder fins. 5. Use brush to...

  • Page 22

    22 5. Clean carbon deposits from muffler components. Note when cleaning carbon deposit, be careful not to damage the catalylic element inside muffler. 6. Replace screen if it is cracked, plugged or has holes burned through. 7. Assemble components in reverse order. B c d a exhaust port cleaning level...

  • Page 23

    G rass t rimmer /b rush c utter o perator ' s m anual 23 carburetor adjustment engine break-in new engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissio...

  • Page 24

    24 a a lubrication level 1. Tools required: 13 mm open end wrench, screwdriver, clean rag. Parts required: power blendx tm 8 oz. (p/n 91014) or lithium base grease. Gear housing 1. Clean all loose debris from gear box. 2. Remove plug (a) and check level of grease. 3. Add grease if necessary, do not ...

  • Page 25

    G rass t rimmer /b rush c utter o perator ' s m anual 25 nylon line replacement level 1. Parts required: echo 2.4mm (0.095 in.) nylon trimmer line 9m (30 feet [two 15 ft. Sections]) echomatic pro trimmer head 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Do not push spool in. ...

  • Page 26

    26 sharpening metal blades three styles of metal blades are approved for use on the echo brush cutter. The 8-tooth blade can be sharpened during normal maintenance. The clearing blade and 80 tooth blade require professional service. Before sharpening, closely inspect blade for cracks (look at the bo...

  • Page 27

    G rass t rimmer /b rush c utter o perator ' s m anual 27 t r a h c g n i t o o h s e l b u o r t m e l b o r p e n i g n e m e l b o r p k c e h c s u t a t s e s u a c y d e m e r e n i g n e - s k n a r c / d r a h s t r a t s t' n s e o d t r a t s r o t e r u b r a c t a l e u f t a l e u f o n ...

  • Page 28

    28 danger do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark. S torage warning during operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwis...

  • Page 29

    G rass t rimmer /b rush c utter o perator ' s m anual 29 s pecifications models --------------------------------------------------- srm-230, srm-230s length ------------------------------------------------------- 1795 mm (70.7 in.) width -------------------------------------------------------- 250 m...

  • Page 30

    30 notes.

  • Page 31

    G rass t rimmer /b rush c utter o perator ' s m anual 31 notes.

  • Page 32

    Echo, incorporated 400 o akwood r oad l ake z urich , il 60047 www.Echo-usa.Com consumer product support 1-800-673-1558 8:30 - 4:30 mon - fri c.S.T. Additional or replacement manuals safety manuals in english/spanish or english/french are available, free of charge, from your echo dealer or at www.Ec...