1. DL manuals
  2. Echo
  3. Trimmer
  4. SRM - 410U
  5. Operator's Manual

Echo SRM - 410U Operator's Manual

Other manuals for SRM - 410U: Operator's Manual
Manual is about: Brush Cutter

Summary of SRM - 410U

  • Page 1

    Warning read rules for safe operation and instructions carefully. Echo provides an operator's manual and a safety manual. Both must be read and understood for proper and safe operation. Grass trimmer/brush cutter operator's manual model srm - 410u x7502163701 x750012311 03/09.

  • Page 2

    2 copyright© 2009 by echo, incorporated all rights reserved. I ntroduction welcome to the echo family. This echo product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the safety manual you found in the same package. You will find...

  • Page 3

    G rass t rimmer /b rush c utter o perator ' s m anual 3 international symbols s afety manual safety symbols and important information throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre- ceded by symbols or key words. The following is...

  • Page 4

    4 physical condition your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye protection wear eye protection that meets ansi z87.1 or ce requi...

  • Page 5

    G rass t rimmer /b rush c utter o perator ' s m anual 5 danger do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the manuals • provide all users of this equipment with the operator’s manual...

  • Page 6

    6 equipment warning use only echo approved attachments. Serious injury may result from the use of a non-approved attachment com- bination. Echo, inc. Will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by echo. Read and compl...

  • Page 7

    G rass t rimmer /b rush c utter o perator ' s m anual 7 p/n 89016054130 p/n x505002310 hot decal (near muffler) d escription locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them. If a decal cannot be read, a new one c...

  • Page 8

    8 1. Power head - includes the engine, clutch, fuel system, ignition system and recoil starter. 2. Throttle trigger lockout - this lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 3. Stop switch - "slide switch" moun...

  • Page 9

    G rass t rimmer /b rush c utter o perator ' s m anual 9 c ontents the echo product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify...

  • Page 10

    10 a ssembly drive shaft / power head tools required: 4 mm hex wrench parts required: power head, drive shaft assembly 1. Stand power head upright on a level surface. 2. Loosen the drive shaft clamp bolt (a) at engine drive shaft clamp, and remove drive shaft locating bolt (b). 3. Remove protective ...

  • Page 11

    G rass t rimmer /b rush c utter o perator ' s m anual 11 1. Align hole in upper plate (d) with notch in gear housing (e), and insert locking tool to prevent splined shaft from turning. Arrow on gear housing flange points to notch location. 2. Remove split pin (f), l.H. Blade nut (g), lower plate (h)...

  • Page 12

    12 a b c u - handle installation tools required: 17 & 19 mm wrench, 4 mm hex wrench parts required: u-handle, clamp w/screws, 8 mm x 55 mm hex bolt, 8 mm flat washer 1. Remove assembling bolt (a) from right hand grip. Install right hand grip (b) onto right hand u-handle (c) until bolt hole in u- han...

  • Page 13

    G rass t rimmer /b rush c utter o perator ' s m anual 13 6. Secure the right hand u-handle by tightening 4 right handle assem- bling bolts (h) loosely. 7. Adjust handles for comfortable operation and tighten handle as- sembling bolt (e) and 4 right handle assembling bolts (h). 8. Route throttle link...

  • Page 14

    14 optional nylon head installation tools required: locking tool parts required: nylon line head. 1. Align hole in upper plate with notch in gear housing, and insert locking tool to prevent splined shaft from turning. 2. Thread line head onto pto shaft by turning it counter-clockwise until head is t...

  • Page 15

    G rass t rimmer /b rush c utter o perator ' s m anual 15 2.Replacing spool note keep line tight on spool. A. Snap spool into housing while pulling line through eyelets with about 15 cm (6 in) extending out. Caution knob tightens counterclockwise, “left”. B. Fasten spool to housing with shaft bolt, s...

  • Page 16

    16 o peration warning moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or se...

  • Page 17

    G rass t rimmer /b rush c utter o perator ' s m anual 17 plastic/nylon grass/weed blades may be used where ever the nylon line head is used. Do not use this blade for heavy weeds or brush! 8 tooth weed/grass blade is designed for grass, garden debris and thick weeds. Do not use this blade for brush ...

  • Page 18

    18 fuel notice: use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the storage section of this manual. Warning alternative fuels, such as e-20 (2...

  • Page 19

    G rass t rimmer /b rush c utter o perator ' s m anual 19 mixing instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close ...

  • Page 20

    20 starting cold engine warning when engine is started, confirm that there is not any abnormal vibration or sound. If there is abnormal vibration or sound, ask your dealer to repair. After refueling tighten fuel cap firmly and check for leakage. In case of fuel leakage repair before starting operati...

  • Page 21

    G rass t rimmer /b rush c utter o perator ' s m anual 21 starting warm engine 1. Press the decompression device (e). 2. Stop switch move stop switch button (a) forward away from the stop posi- tion. 3. Purge bulb pump purge bulb (c) until fuel is visible in the "clear" fuel return line. 4. Recoil st...

  • Page 22

    22 m aintenance warning moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or ...

  • Page 23

    G rass t rimmer /b rush c utter o perator ' s m anual 23 b a air filter level 1. Tools required: 25 - 50mm (1 - 2 in.) cleaning brush parts required: repower tm tune-up kit note always brush dirt and debris away from air cleaner area prior to cleaning air filter. 1. Brush dirt off air cleaner area. ...

  • Page 24

    24 fuel filter level 1. Tools required: 200- 250 mm (8 - 10 in.) length of wire with one end bent into a hook, clean rag, funnel, and an approved fuel container. Parts required: repower tm tune-up kit danger fuel is very flammable. Use extreme care when mixing, storing or handling. 1. Use a clean ra...

  • Page 25

    G rass t rimmer /b rush c utter o perator ' s m anual 25 cooling system level 2. Tools required: air compressor and safety nozzle, or: 4 mm hex wrench, 25 - 50 mm (1 - 2 in.) cleaning brush. Parts required: none. Important to maintain proper engine operating temperatures, cooling air must pass freel...

  • Page 26

    26 exhaust port cleaning level 2. Tools required: 4 & 5 mm hex wrench, wood or plastic scraper parts required: as needed: heat shield 1. Remove spark plug lead from spark plug, and remove muffler cover (2 screws). 2. Place piston at top dead center. Remove muffler (a) and heat shield (b). 3. Use a w...

  • Page 27

    G rass t rimmer /b rush c utter o perator ' s m anual 27 caution when starting, idling adjustment speed should be adjusted not to rotate the cutting attachment. Correct idle speed is adjusted 2300 to 2700 r/min. Or 1/4 turn ccw from the point the cutting attachment stops moving. When there is some t...

  • Page 28

    28 lubrication level 1. Tools required: 8 & 13 mm open end wrench, screwdriver, clean rag. Parts required: power blendx tm 8 oz. (p/n 91014) or lithium base grease. Gear housing 1. Clean all loose debris from gear box. 2. Remove plug (a) and check level of grease. Grease should fill gear case to bot...

  • Page 29

    G rass t rimmer /b rush c utter o perator ' s m anual 29 sharpening metal blades three styles of metal blades are approved for use on the echo brush cutter. The 8-tooth blade can be sharpened during normal mainte- nance. The clearing blade and 80 tooth blade require professional service. Before shar...

  • Page 30

    30 danger fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result. T roubleshooting t r a h c g n i t o o h s e l b u o r t m e l b o r p e n i g n e m e l b...

  • Page 31

    G rass t rimmer /b rush c utter o perator ' s m anual 31 danger do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark. S torage warning during operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable ...

  • Page 32

    32 s pecifications model ---------------------------------------------------- srm-410u length ------------------------------------------------------- 1860 mm (73.2 in.) width -------------------------------------------------------- 630 mm (24.8 in.) height -------------------------------------------...

  • Page 33

    G rass t rimmer /b rush c utter o perator ' s m anual 33 notes.

  • Page 34

    34 notes.

  • Page 35

    G rass t rimmer /b rush c utter o perator ' s m anual 35 notes.

  • Page 36

    Echo, incorporated 400 o akwood r oad l ake z urich , il 60047-1564 7-2 suehirocho 1-chome, ohme, tokyo, 198-8711, japan phone: 81-428-32-6118 fax: 81-428-32-6145 gb © 2009 s05403001001/s05403999999.