Echo SRM-5000 Service Data

Other manuals for SRM-5000: Operator's Manual

Summary of SRM-5000

  • Page 1

    Srm-5000 10-52d-02 1 lntroduction we are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications, illustrations and directions in this service data are based on the latest products inf...

  • Page 2

    Service information srm-5000 2 1 service information 1-1 specifications model srm-5000(l) srm-5000(u) dimensions length* mm(in) 1860 (73.2) 1860 (73.2) width mm(in) 325 (12.8) 700 (27.6) height mm(in) 265 (10.4) 430 (16.9) dry weight ** kg(lb) 8.3 (18.30) 8.7 (19.18) engine type kioritz, air-cooled,...

  • Page 3

    Service information srm-5000 3 1-2 technical data engine idling speed r/min 2000 - 2700 operating speed r/min 7500 - 8500 wide open throttle speed r/min 9700 - 10300 †1 10500 - 12000 †2 clutch engagement speed r/min 3400 - 3900 compression pressure mpa (kgf/cm 2 ) (psi) 0.93 (9.5) (135) ignition sys...

  • Page 4

    Service information srm-5000 4 1-3 torque limits descriptions size kgf•cm n•m in•lbf starter pawl carrier m 8 80 - 100 8 - 10 70 - 90 system pawl carrier nut m 8 160 - 200 16 - 20 140 - 175 starter case m 5* 35 - 50 3.5 - 5 30 - 45 ignition magneto rotor (flywheel) m 10 200 - 240 20 - 24 175 - 210 s...

  • Page 5

    Service information srm-5000 5 5k223 5k224 5k225 5k016 5k042 5k222 0 5 10 1 2 3 4 5 6 7 8 9 10 11 5k245 5k246 1-5 service limits a b c d e f g h k l m description mm (in) a cylinder bore when plating is worn and aluminium can be seen b piston outer diameter min. 43. 88 (1.728) c piston pin bore max....

  • Page 6

    Service information srm-5000 6 a 1.5 1.65 1.3 0.4 a b a 20 20 40 40 60 60 80 80 120 120 140 140 160 160 180 180 20 20 100 100 ec ho key part number description used for: 1 897801-33330 tachometer pet-1000 measuring engine speed to adjust carburettor 2 895610-79920 l-hex wrench (4 mm) removing and in...

  • Page 7

    Service information srm-5000 7 2 emission adjustment guide 2-1 general adjusting rules a. Before starting the unit for adjustment, check the following items. 1. The correct spark plug must be clean and properly gapped. 2. The air filter element must be clean and properly installed. 3. The muffler ex...

  • Page 8

    Service information srm-5000 8 2-3 adjusting carburettor 1. Start engine and warm it up well as follows. (1) warm engine up for approx. 1 minute at idle speed. (2) warm it up alternating engine speed between half-throttle speed (partial speed approx. 6,000 r/min with nylon line head, 7,000 r/min wit...

  • Page 9

    Service information srm-5000 9 (g) echo echo 4. Start engine again, and verify engine idle speed ranges from 2,000 to 2,700 r/min, and wot engine speed ranges from 9,700 to 10,300 r/min (when using metal blade : 10,500 - 12,000 r/min). Make sure the cutting device does not rotate when engine is idli...