Telescopic pole chain saw model:cs015 user manual important: read and understand this manual before assembling or operating this appliance. Improper use of this appliance can cause severe injury or death. Keep this manual in a safe place for future reference. Any questions or problems-please call th...
1 contents: page 2……………………………………………….Safety symbols explanation page 2……………………………………………….Technical data page 3-6…………………………………………….Safety instructions page 7……………………………………………. Assembly page 8……………………………………………….Saw chain tension page 9……………………………………………….Saw chain tension adjustment page 10………………………………...
2 explanation of symbols on your product do not use in the rain. Read the user manual before using the machine. Always wear a helmet, goggles and ear protection. Risk of fatal electric shock. Work at least 10m distance from overhead power lines.. Danger do not operate this equipment when there are c...
3 product identificat ion contents: 1. Guard 2.Saw chain 3. Guide bar 4. Power head 5. Inner adjustable 6. Locking knob 7.Collet. 8.Under pole 9.Grip 10.Strap 11. Buckle 12.Handle 13.Switch lockout 14.On/off trigger 15.Mains power cable 16.Oil filler cap. Safety instructions warning read all safety ...
4 your body isearthed or grounded. C) do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. D) do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges...
5 unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. E) maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operatio...
6 never stand on a ladder or other type of unstable support while using the pole saw. Always use both hands to operate pole saw. Keep a firm, steady pressure on the pole saw while cutting but do not try to force the saw through the wood. Do not use the pole saw to cut limbs larger in diameter than t...
7 pole saw information pole saw assembly (warning: cutting edges on chain are sharp. Use protective gloves when handling chain.) 1. Lay chain out flat. 2. Turn adjusting screw counterclockwise (see figure 1). Continue to turn adjusting screw until adjusting block is to rear of adjusting plate. 3. In...
8 6. Fill with chain oil before use. Always check oil level before use. A full tank of oil will last approximately 30 minutes. (see figure 2) pole saw information saw chain tension warning:unplug chain saw from power source before adjusting saw chain tension. Severe injury or death could occur from ...
9 figure 4 2. Turn adjusting screw on front of power head clockwise until slack is out of chain. ( see figure 5) figure 5 3. Wearing protective gloves, pull down on chain to check chain tension. 4. Do not over-tension chain. Over-tensioning will cause excessive wear and will reduce the life of the g...
10 adjusting pole length the pole saw has a telescoping pole assembly that will extend from 1.8 meters (fully retracted) to 2.7 meters (fully extended). The collet with a locking knob is used to hold the pole in position at any extended length. 1. To extend the pole, loosen the locking knob(see figu...
11 5. When ready to make a cut, press in trigger lockout and squeeze trigger(see figure 9). This will turn pole saw on. Releasing trigger will turn pole saw off. Make sure saw is running before starting a cut. Figure 9 6. When starting a cut, place moving chain against wood. Hold pole saw firmly in ...
12 normal guide bar maintenance 1. Remove guide bar from chain saw. 2. Remove sawdust from guide bar groove periodically. Use putty knife or wire (see figure 11). 3. Clean oil slots after each day of use. 4. Remove burrs from sides of guide bar. Use flat file to make side edges square. Replace guide...
13 figure 12). (note: file at midpoint of guide bar.) figure 12 note: this illustration shows file guide placement and filing direction for sharpening cutters on left side of chain. 4. Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see figure 13). This wi...
14 figure.14 figure.15 replacing saw chain replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Check drive sprocket for wear when replacing chain. This will maintain proper driving of chain. (note: for proper chain and drive sproc...
15 figure 16 caution: do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. Storage if storing saw for more than 30 days, follow steps below.1. Drain oil tank after each use. 2. Remove and clean guide bar and chain. Clean guide bar and chain by soaking ...
