- DL manuals
- Eckman
- Chainsaw
- EKECS03
- Instruction Manual
Eckman EKECS03 Instruction Manual
Summary of EKECS03
Page 1
2400w electric chain saw model ekecs03 instruction manual please read and save the instruction manual for future reference any questions please call the eckman helpline on：0844 441 3011 or go to www.Eckman.Co.Uk.
Page 2
- 1 - contents environmental protection....................................................................................- 2 - safety instructions.................................................................................................- 2 - description of symbols..............................
Page 3
- 2 - environmental protection waste electric products should not be disposed of with household waste. Please recycle check with your local authority or retailer for recycling advice. Safety instructions before using the chainsaw, please read the following instructions and follow them during operati...
Page 4
- 3 - safety rules – general and for electric chainsaws 1. Replacement parts. When servicing, use only identical replacement parts. 2. Plugs. Do not modify the plug connected to the power lead in any way. 3. Cleanliness. Keep work area clean. Cluttered areas invite injuries. Do not start cutting unt...
Page 5
- 4 - inspect periodically and if damaged, have repaired by authorized service facility. Keep mains power lead clear of the chain and operator at all times. Never carry saw by the mains lead and keep cord away from oil and sharp edges. Keep the chain sharp, clean, and properly tension-adjusted for b...
Page 6
- 5 - ⑦ . Only use replacement bars and chains specified by the manufacturer or the equivalent. 20. Power supply. Connect chain saw to correct voltage, that is, be sure that the voltage supplied is the same as that specified on the nameplate of the tool. Technical data factory model/eckman model sf7...
Page 7
- 6 - start type soft touch start function of led indicator power overload indicator parts identification 1 cable + plug (uk plug supplied) 2 rear handle 3 on/off switch 4 lock-off button 5 oil tank cap 6 front handle 7 activation lever for kickback brake (hand guard) 8 nose sprocket 9 oregon bar 10...
Page 8
- 7 - setting chain and chain bar chain and chain bar assembly for model with sds tool-less tensioning system place the chainsaw with the motor on a cover to avoid any mess from the oil. Place the chain in the grove of the bar. Pay attention to the correct running direction. As shown by the running ...
Page 9
- 8 - setting the chainsaw tension tensioning chain for model with sds tool-less tensioning system loosen the lock knob by turning it anti-clockwise approximately 1-2 turns. Check whether all chain links lie correctly in the guide tracks of the bar. Press the tension ring inwards and turn it in a cl...
Page 10
- 9 - checking the automatic oil function switch on the chainsaw, rev it up and point the tip of the saw towards a piece of paper laying on the ground. If a patch of oil appears and becomes larger, then the automatic oil function is working. If there are no traces of oil even though the oil tank is ...
Page 11
- 10 - note. Ensure the brake is working efficiency, check its operation every time you use the chain saw before commencing work with it . Warning. The trigger must never be depressed before pulling back the front hand guard. 1.Hold the electric chain saw by its grip with both hands. 2.To start the ...
Page 12
- 11 - 2. Reset the gripping teeth at a lower point when sawing thicker logs by pulling the chain saw slightly backwards, until the gripping teeth release, and reposition at lower level to continue sawing. Do not remove the saw completely from the wood. 3. Log supported along entire length: cut from...
Page 13
- 12 - ●to fell trees, observe all the safety regulations and proceed as follows: the chainsaw may be used to fell only trees which are smaller in diameter than the length of the bar and chain. If the saw chain gets jammed, release it using a wooden wedge. ●felling trees is dangerous and requires pr...
Page 14
- 13 - chain brake in the event of kick-back, the chain brake will be actuated via the front finger guard. The front finger guard is pushed forwards by the back of the hand and this causes the chain brake to stop the chain saw, or rather the motor, within 0.15 of a second. Releasing the chain brake:...
Page 15
- 14 - chainsaw maintenance warning. Always ensure that the machine is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures. 1. Always keep the air holes clean on the electric chainsaw body. They tend to become clogged with sawdust during ...
Page 16
- 15 - is always greater than the chain’s transmission links so that the latter do not touch the bottom. Replace the bar if required. The chainsaw should be periodically serviced to check the correct operation of the chain, chain drive, motor and brake. Caution: water must never come into contact wi...
Page 17
- 16 - poor cutting performance blunt saw chain sharpen or replace the saw chain. Chain tension check chain tension. Saw chain fitted incorrectly check saw chain chain jumps off guide bar chain tension check chain tension. Chain works with difficulty chain tension check chain tension. Chain becomes ...
Page 18
- 17 - ec declaration of conformity we, the zhejiang safun industrial co.,ltd address: 7 south mingyuan ave,economic development zone,yongkang, zhejiang china hereby declare by our own responsibility that the product : chain saw ,type sf7j101-24-sln (ekman model ekecs03) is according to the basic re...
Page 19
- 18 -.
Page 20
- 19 -.