1. DL manuals
  2. Eckman
  3. Trimmer
  4. EKEMS2
  5. Instruction manual

Eckman EKEMS2 Instruction manual

Manual is about: 4-IN-1 1200W EXTENDABLE ELECTRIC HEDGE TRIMMER, GRASS TRIMMER/ BRUSH CUTTER & CHAINSAW BRANCH LOPPER SET

Summary of EKEMS2

  • Page 1

    4-in-1 1200w extendable electric hedge trimmer, grass trimmer/ brush cutter & chainsaw branch lopper set model ekems2 instruction manual 回 please read and save the instruction manual for future reference any questions please call the eckman helpline on：0844 441 3011 or go to www.Eckman.Co.Uk.

  • Page 2: Contents:

    - 1 - contents: i. Symbols / pictures marked on the product or used in manual............2-3 ii . General safety instruction s.…… ......................................................... .3-6 iii. Parts identification.....................................................................................

  • Page 3

    - 2 - i. Symbols pictures marked on the product or used in manual read the user manual before using the machine warning! Wear ce approved eye protection! Wear ce approved ear and head protection! Wear gloves to protect your hands. Wear sturdy and high safety boots. Before maintenance or repair – swi...

  • Page 4

    - 3 - c utting length of chainsaw lopper 220mm c utting length of hedge trimmer 400mm cutting length of brush cutter 230mm c utting length of grass trimmer 400mm warning: read and understand all instructions. Deviation from these instructions can result in serious injury. Ii . General safety instruc...

  • Page 5

    - 4 - ● do not use the unit if it is damaged o r poorly adjusted. Never remove the machine’s guard. Serious injury to the operator or bystanders could result as well as damage to the machine. ● inspect the area to be cut and remove all debris that could become entangled in the nylon cutting head or ...

  • Page 6

    - 5 - before re-using the machine after any impact, check the machine for wear and tear or damage. If necessary have the machine repaired. Wear ce approved eye and ear protection and if applicable a hard hat. Periodically check and maintain the unit. Only have the unit repaired by an authorised expe...

  • Page 7

    - 6 - i) before you start working remove any debris from the ground to avoid tripping. J) always stand in a secure position and keep your balance. K) always keep extension and connecting cables behind the saw or away from the cutting area. L) only use spare parts approved by the manufacturer, in par...

  • Page 8

    - 7 - medical implant manufacturer before operating this machine. Iii. Parts identification - drive unit: 1 motor housing case 2.Throttle control trigger 3.Trigger lockout 4.Main cable (10m with fused uk plug) 5.“d” handle 6.Hand tighten knob.

  • Page 9

    - 8 - - tool attachments: 7 chainsaw pruner 8 brush cutter 9 grass trimmer 10 hedge trimmer 11. Optional extra extension pole.

  • Page 10

    - 9 - - accessories: 19 hand-tighten knobs 12 protection guard for line trimmer/brush cutter 13 belt 14 chain saw protection cover 15 oregon bar 16 oregon chain 17 blade 18 double line, bump-feed spool 20 21 22 23 24 25 20 hexagon key 21 blade retainer 22 hexagon socket wrench 23 blade retainer nut ...

  • Page 11

    - 10 - before assembly firstly unpack and check all parts have been supplied. If you think any parts are missing, check the packaging again before calling the eckman helpline on 0844 441 3011. Iv. Technical data eckman code/factory code ekems2/sf7a214 rated voltage 230v~ 50hz rated power: 1200w no l...

  • Page 12

    - 11 - the handle has two parts. First seperate the upper and lower parts by removing the four hex-bolts using the hex key supplied. The power unit handle has two black rubberized cover sections. The longer one is sponge rubber, the shorter one is strong rubber. The longer which has a soft feel is f...

  • Page 13

    - 12 - clip to the power unit and adjust for length and comfort. (photo 4-5) vi. Chainsaw lopper attachment assembly this also need to be assembled and comprises the following parts: warning: be sure to fill the oil reservoir with the appropriate chain oil otherwise you will seize and burn out the c...

  • Page 14

    - 13 - warning the saw chain has very sharp edges. Use protective gloves for safety. 1、loosen the nut and remove the chain cover 2、mount the guide bar then fit the saw chain around the bar and sprocket.(photo 7) warning pay attention to the correct direction of the saw chain(photo 8) 3.Fit the chain...

  • Page 15

    - 14 - warning it is very important to maintain the proper chain tension. Rapid wear of the guide bar or the chain coming off easily can be caused by improper tension. Especially when using a new chain, take good care as it will expand when first used. Vii. Hedge trimmer attachment this comes suppli...

  • Page 16

    - 15 - attach shaft to the groove then mount plastic seat to tighten. (see photo14-16) 2) fitting the safety guard to the brush cutter mount two inner flanges to the safety guard then put on blade and blade retainer fixed by blade retainer nut using hexagon socket wrench, you ’ll need to line up the...

  • Page 17

    - 16 - 3) fitting the safety guard to the grass trimmer if you use the unit as a grass trimmer follow the instructions below: 1. Loosen the blade retainer nut clockwise and remove the blade retainer. 2. Mount the grass trimmer head and tighten it.(see photo 22-23) note: please store the blade retain...

  • Page 18

    - 17 - note: never attempt to lock a switch in the on position. Xi . Maintenance store the tool, instruction manual and accessories in a secure, dry place. In this way you will always have the information ready to hand. Remove dust and dirt regularly. Re-lubricate all moving parts at regular interva...

  • Page 19

    - 18 - store the machine in a place out of the reach of children. The optimum storage temperature is between 10 and 30°c. Xiii.Guarantee this product is guaranteed for a period of 36 months from date of purchase. Any modification or misuse of this machine will invalidate your guarantee. Your statuto...

  • Page 20: Exploded View & Parts List

    - 19 - imported by eckman co.,ltd add: 29 welbeck street,london w1g 8da, england 12 exploded view & parts list.

  • Page 21

    - 20 -.

  • Page 22

    - 21 - no name no name 1 nut 47 armature 2 anti-dust cover 48 bearing 608 3 upper press plate 49 carbon brush 4 3 teeth blade 50 screw 5 down press plate 51 brush holder 6 shield ring 32 52 rear holder 7 bearing 6002 53 axle sheath 8 key axle 54 fan 9 big 55 nut 10 bearing 609 56 cable 11 screw 57 c...