- DL manuals
- Ecler
- Amplifier
- CA120
- User Manual
Ecler CA120 User Manual - page 11
11
4.6. Lock mode
To switch the CA120 lock mode on or off hold in the VOL/MUTE control for 10 seconds
from the VOL/MUTE mode. The LED SETTING indicators will flash 3 times to indicate that lock mode
is now on. When in lock mode the device cannot be managed using the VOL/MUTE control (it will
flash three times to show that it is in that mode when you turn the knob). This will protect the
equipment from unwanted handling until it is restored to normal operation after holding the
VOL/MUTE control in for a further 10 seconds (the LED SETTING indicators will flash twice to show
that the lock mode is off).
Note: once lock mode is activated it will stay activated even when the equipment is turned
off and on again. It will stay in lock mode until the VOL/MUTE control is held in for 10 seconds again.
4.7. Restore default settings and update firmware
If you would like to restore the CA120 to factory settings, follow this procedure:
1. Unplug the equipment then press and hold the knob in.
2. Plug back the unit without releasing the knob. The MUTE LED indicator will flash.
3. Wait a few seconds and then switch the CA120 off again.
4. The next time you turn it on, the factory settings will be in the memory.
Note: for instructions on how to update the unit's firmware, see the product web page at
www.ecler.com
, where you will find the update software utility and instructions on how to proceed.
5. CLEANING
The CA120 must not be cleaned with solvents or abrasive substances which may damage
the prints. Clean using a cloth moistened in water and a neutral liquid detergent, then dry with a clean
cloth. Under no circumstances allow water to enter any of the orifices in the equipment.
Summary of CA120
Page 1
1 user manual manual de instrucciones notice d'utilisation bedienungsanleitung ca120
Page 3
3 instruction manual 1. Important note 04 1.1. Compliance with international standards 04 2. Introduction 04 3. Installation 05 3.1. Location and assembly 05 3.2. Mains connection 05 3.3. Audio input connections 05 3.4. Audio output connections 06 3.5. Remote control options 06 4. Operation and usag...
Page 4
4 1. Important note congratulations! You have acquired the result of painstaking design and manufacturing. Thank you for having chosen our ca120 micro amplifier. In order to get the optimum operation and efficiency from your product, it is very important - before you plug anything - to read this man...
Page 5
5 3. Installation 3.1. Location and assembly the ca120 is suitable for installation on a wall or under a surface (table, shelf, cupboard, etc.), thanks to its design and layout of its connectors, controls and led indicator lights. 3.2. Mains connection the amplifier is powered by alternating current...
Page 6
6 line3/mic signal attenuates to that of the line1 when it exceeds the activation threshold line2 + line3/mic: the line2 and line3/mic inputs are mixed, amplified and delivered to the l and r out outputs. If the talkover function is active, the line3/mic signal attenuates to that of the line2 when...
Page 7
7 o baud rate: 9600 (fixed, without auto negotiation) o data bits: 8 o parity: none o stop bits: 1 o flow control: none receiver ir: the built-in ir receiver gives general volume control of the ca120 and its mute on / off function from the revo-ir remote control included with the unit. 4. Operatio...
Page 8
8 4.2. Special active source selection mode and setting adjustments use the knob on the front panel to access special modes for selecting active sources and adjusting levels and equalization (bass and treble). You can access these modes by holding in the knob for a certain time and then turning it. ...
Page 9
9 notes: 1. If the device is in special mode for 10 seconds and the front knob is not touched, the equipment automatically reverts to vol/mute mode. 2. In tone control mode, when you turn the knob in either direction it flashes fast while the gain of the affected tone increases. When either end of t...
Page 10
10 on/stby: the green light comes on when the equipment is in normal operating mode and it goes orange when it is in standby or low consumption mode (standby). Level: this flashes when you adjust the general level of the device. It also lights up during special adjustment modes, input levels (see se...
Page 11
11 4.6. Lock mode to switch the ca120 lock mode on or off hold in the vol/mute control for 10 seconds from the vol/mute mode. The led setting indicators will flash 3 times to indicate that lock mode is now on. When in lock mode the device cannot be managed using the vol/mute control (it will flash t...
Page 12
12 6. List of functions 1. Level indicator light 2. Bass indicator light 3. Treble indicator light 4. Line1 indicator light 5. Line2 indicator light 6. Mic indicator light 7. Vol/mute knob 8. Sp input signal presence indicator light 9. Clip indicator light 10. Mute indicator light 11. On/stby on or ...
Page 13
13 7. Diagram of functions.
Page 14
14.
Page 15
15 manual de instrucciones 1. Nota importante 16 1.1. Conformidad con normativas internacionales 16 2. IntroducciÓn 16 3. InstalaciÓn 17 3.1. Ubicación y montaje 17 3.2. Conexión a red eléctrica 17 3.3. Conexiones de audio de entrada 17 3.4. Conexiones de audio de salida 18 3.5. Opciones de control ...
Page 16
16 1. Nota importante ¡enhorabuena!. Vd. Posee el resultado de un cuidadoso diseño y una esmerada fabricación. Agradecemos su confianza por haber elegido nuestro micro amplificador ca120. Para conseguir la máxima operatividad del aparato y su máximo rendimiento es muy importante, antes de su conexió...
Page 17
17 3. InstalaciÓn 3.1. Ubicación y montaje el ca120 admite instalación en pared o bien sobre o bajo una superficie (mesa, estantería, mueble, etc.), gracias a su diseño y a la disposición de sus conectores, controles e indicadores led. 3.2. Conexión a red eléctrica el amplificador se alimenta con co...
Page 18
18 el ca120 permite los siguientes modos de trabajo, en función de qué fuentes de entrada sean seleccionadas como activas: line1: sólo la entrada line1 es enviada al bus de mezcla para ser amplificada y entregada en las salidas out l y r line2: sólo la entrada line2 es enviada al bus de mezcla p...
Page 19
19 puerto mute: el conector mute permite la conexión de un cierre de contacto externo libre de potencial para silenciar totalmente el ca120 en caso de que un dispositivo externo actúe sobre él (ejemplo: un sistema de avisos para emergencias y evacuación centralizado). puerto rs-232: el puerto de...
Page 20
20 si se realiza un ajuste de volumen mediante el mando a distancia por infrarrojos las indicaciones visuales mediante los leds level y mute son exactamente las mismas que para el ajuste mediante el control giratorio del panel frontal. 4.2. Modos especiales de selección de fuentes activas y ajuste d...
Page 21
21 notas: 1. Si, estando en cualquier modo especial, transcurren 10 segundos sin actuar sobre el control giratorio frontal, se retornará automáticamente al modo por defecto de ajuste de vol/mute. 2. En el modo de ajuste de tonos, al girar el control en uno u otro sentido, éste parpadea rápidamente m...
Page 22
22 del pasaje sonoro. De lo contrario la señal amplificada presentaría altos niveles de distorsión y una baja calidad acústica e inteligibilidad. Nota: si la señal de entrada es excesivamente alta, iluminándose el indicador clip muy frecuentemente durante un intervalo de tiempo corto (pocos segundos...
Page 23
23 4.6. Modo de bloqueo para entrar o salir del modo de bloqueo del ca120 es preciso mantener pulsado el control vol/mute durante un período de 10 segundos, desde el modo vol/mute. Los indicadores led setting parpadearán 3 veces para indicar la entrada en el modo de bloqueo. En el modo de bloqueo no...
Page 24
24 6. Lista de funciones 1. Indicador luminoso level 2. Indicador luminoso bass 3. Indicador luminoso treble 4. Indicador luminoso line1 5. Indicador luminoso line2 6. Indicador luminoso mic 7. Control giratorio digital vol/mute 8. Indicador luminoso de presencia de señal en la entrada sp 9. Indicad...
Page 25
25 7. Diagrama de funciones.
Page 26
26.
Page 27
27 notice d’instructions 1. Note importante 28 1.1. Conformité avec les réglementations internationales 28 2. Introduction 28 3. Installation 29 3.1. Emplacement d'installation et montage 29 3.2. Raccordement au secteur 29 3.3. Branchement de l'entrée audio 29 3.4. Branchement de la sortie audio 30 ...
Page 28
28 1. Note importante félicitations ! Vous avez en votre possession le résultat d’une conception et d’une fabrication particulièrement soignées. Nous vous remercions de votre confiance pour avoir choisi notre micro-amplificateur ca120. Pour exploiter au mieux toutes les fonctionnalités et obtenir un...
Page 29
29 port de commande rs-232, compatible avec eclercomm logiciels (gratuit) et de contrôle protocole ca-net port mute pour mise en sourdine totale de l'unité par fermeture de contact externe 3. Installation 3.1. Emplacement d'installation et montage grâce à sa conception et à la disposition de ses con...
Page 30
30 le ca120 propose les modes de fonctionnement suivants en fonction des sources d'entrée sélectionnées en tant que sources actives : line1 : seule l'entrée line1 est envoyée au bus de mixage pour être amplifiée et délivrée aux sorties out l et r. line2 : seule l'entrée line2 est envoyée au bus ...
Page 31
31 réalisé à l'aide de cette dernière commande est prioritaire. Le cas échéant, le ca120 reprend les valeurs indiquées par le panneau mural lorsque sa position est de nouveau modifiée, et ainsi de suite. port mute : le connecteur mute permet de raccorder une fermeture de contact externe sec pour m...
Page 32
32 une pression rapide du bouton vol/mute permet d'activer/désactiver la fonction de mise en sourdine de l'unité (mute on/off). Le voyant mute s'allume lorsque la mise en sourdine est activée. Lorsque le réglage du volume est réalisé au moyen de la télécommande infrarouge, les indications visuelles ...
Page 33
33 remarques : 1. Sous un mode spécial, l'appareil retourne automatiquement au mode par défaut de réglage vol/mute lorsque le bouton rotatif avant n'est pas touché pendant 10 secondes. 2. Sous le mode de réglage de tonalité, le bouton se met à clignoter rapidement lorsqu'il est tourné dans un sens o...
Page 34
34 permanence, à savoir que ces derniers s'allument au maximum au rythme des fréquences les plus graves du passage du son. Dans le cas contraire, le signal amplifié présente des niveaux élevés de distorsion, une faible qualité acoustique et une netteté phonique médiocre. Remarque: si le signal d'ent...
Page 35
35 4.6. Mode de verrouillage pour accéder au mode de verrouillage du ca120 et le quitter, il suffit de maintenir le bouton vol/mute enfoncé pendant 10 secondes (sous le mode vol/mute). Les voyants setting se mettent à clignoter 3 fois de suite pour signaler que l'appareil est passé en mode de verrou...
Page 36
36 6. Liste des fonctions 1. Voyant lumineux level 2. Voyant lumineux bass 3. Voyant lumineux treble 4. Voyant lumineux line1 5. Voyant lumineux line2 6. Voyant lumineux mic 7. Bouton rotatif numérique vol/mute 8. Voyant lumineux de présence de signal en entrée sp 9. Voyant lumineux d'écrêtage clip ...
Page 37
37 7. SchÉma de fonctions.
Page 38
38.
Page 39
39 bedienungsanleitung 1. Wichtiger hinweis 40 1.1. Auslegung gemäß internationaler normen 40 2. Einleitung 40 3. Aufstellung 41 3.1. Aufstellungsort und montage 41 3.2. Anschluss an das stromnetz 41 3.3. Anschluss der audioeingänge 41 3.4. Anschluss der audioausgänge 42 3.5. Optionen der fernsteuer...
Page 40
40 1. Wichtiger hinweis herzlichen glückwunsch. Sie haben sich für ein sorgfältig konzipiertes, hochwertiges produkt entschieden. Wir danken ihnen für ihr vertrauen bei der auswahl des kompaktverstärkers ca120. Für einen optimalen betrieb und maximale leistung ist es unbedingt erforderlich, vor dem ...
Page 41
41 rs-232-steueranschluss, mit eclercomm kompatibel (kostenlose) software-und steuerungsprotokoll ca-net mute-anschluss zur stummschaltung der anlage durch externen abschaltkontakt 3. Aufstellung 3.1. Aufstellungsort und montage aufgrund seiner bauform und der anordnung der anschlüsse, regler und ...
Page 42
42 line1: nur eingang line1 wird zum mix-bus übertragen, um dort verstärkt und an die ausgänge out l und r weitergeleitet zu werden. line2: nur eingang line2 wird zum mix-bus übertragen, um dort verstärkt und an die ausgänge out l und r weitergeleitet zu werden. line3/mic: nur der mikrofoneing...
Page 43
43 mute-anschluss: der mute-anschluss ermöglicht den anschluss eines potenzialfreien externen schließkontaktes, mit dem der ca120 bei aufschaltung eines externen gerätes (z. B. Notfall-durchsagesystem und zentrale evakuierung) vollständig stummgeschaltet werden kann. Rs-232-anschluss: der serielle k...
Page 44
44 4.2. Sonderbetriebsarten zur auswahl der aktiven audioquellen und einstellung der zugehörigen paramete Über den drehregler an der vorderseite können besondere betriebsarten (auswahl der aktiven audioquellen und pegel- bzw. Eq-regelung (tiefen und höhen)) aktiviert werden. Die aktivierung und bedi...
Page 45
45 hinweise: 1. Wird der drehregler an der vorderseite in einer beliebigen sonderbetriebsart 10 s lang nicht betätigt, so wird automatisch wieder der standardmäßige einstellbetrieb vol/mute wirksam. 2. Dreht man den regler im modus klangregelung in eine richtung, so ist am schnellen blinken zu erken...
Page 46
46 höchstens im takt der tiefsten klangfrequenzen aufflackern. Andernfalls klingt das verstärkte signal sehr stark verzerrt, klang- und hörqualität werden stark beeinträchtigt. Anmerkung: wenn das eingangssignal zu stark ist, so dass die clip- anzeige innerhalb kurzer zeit (wenige sekunden) sehr häu...
Page 47
47 4.6. Gerätesperre zum ein- bzw. Ausschalten der gerätesperre muss vol/mute im entsprechenden modus (vol/mute) 10 s lang gedrückt gehalten werden. Die led-anzeigen setting blinken 3- mal und signalisieren, dass die sperre aktiv ist. Bei aktiver sperre kann die anlage mittels vol/mute nicht bedient...
Page 48
48 6. Funktionsliste 1. Led-anzeige level 2. Led-anzeige bass 3. Led-anzeige treble 4. Led-anzeige line1 5. Led-anzeige line2 6. Led-anzeige mic 7. Digitaler drehregler vol/mute 8. Led-anzeige für eingangssignalerkennung sp 9. Led-anzeige verzerrung clip 10. Led-anzeige stummschaltung mute 11. Led-a...
Page 49
49 7. Funktionsdiagramm.
Page 50
50 8. Technical characteristics 8. CaracterÍsticas tÉcnicas 8. CaractÉristiques techniques 8. Technische daten power (stereo/mono) 2x56w@4 1% thd 2x68w@4 10% thd 2x34w@8 1% thd 2x41w@8 10% thd frequency response 15hz - 30khz (-3db) thd+noise @ 1khz full power speaker out thd+noise aux out ch...
Page 51
51 9. Block diagram 9. Diagrama de bloques 9. SchÉma fonctionnel 9. Blockschaltbild.
Page 52
10. Configuration diagram 10. Diagrama de configuraciÓn 10. SchÉma de configuration 10. KonfigurationsÜbersicht ecler laboratorio de electro-acústica s.A. Motors 166-168, 08038 barcelona, spain internet http://www.Ecler.Com e-mail: info@ecler.Es 50.0269.01.00 -6db 0db sensitivity phantom on off sens...