- DL manuals
- Ecler
- Amplifier
- MPA4-80R
- User Manual
Ecler MPA4-80R User Manual - page 5
5
MPA6-80R
The MPA6-80R amplifier station consists of six 85W/4
amplifiers which can be configured
through a set of switches found on the rear panel. This allows multiple amplification setups useful in
many situations, for example:
Six mono amplifiers for six different mono inputs.
When setup this way, the MPA R is able to amplify six different audio signals, each one having a
dedicated volume control.
Six mono amplifiers for one common mono input.
The amplifier operates now with just one input signal for all amplifiers, but preserves the ability to control
each channel volume independently. This setup is useful when distributing signals to different zones.
Six mono amplifiers for one common stereo input.
This setup is similar to the previous example but the input is now a stereo signal. The amplifier adds
both stereo channels together converting them into a mono signal.
Three stereo amplifiers for three different stereo inputs.
Each stereo channel offers a dedicated volume control. Useful for addressing three zones with three
different stereo signals.
Three stereo amplifiers for one common stereo input.
This setup is similar to the previous example but the input is now a single stereo signal which is fed to all
three amplifiers.
Three bridged amplifiers for three different mono inputs.
Useful for addressing three zones with three different mono signals. Each bridged channel offers a
dedicated volume control. With a bridged amplifier you obtain doubled output power with a load of at
least 8
.
Three bridged amplifiers for a common mono input.
The MPA operates now with a single mono signal for three mono amplifiers, each one with its own
volume control.
Three bridged amplifiers for a common stereo input.
This setup is similar to the previous example but the input is now a stereo signal. The amplifier adds
both stereo channels together converting them into a mono signal.
Four mono amplifiers and one bridged amplifier for one common mono input.
Useful for setups with four amplifiers for mid-range speakers and tweeters and an extra (bridged)
amplifier for a subwoofer.
Summary of MPA4-80R
Page 1
User manual manual de instrucciones notice d'utilisation bedienungsanleitung.
Page 2
2 graphic symbol explanation the lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to person...
Page 3
3 instruction manual 1. Important remark 04 2. Introduction 04 3. Installation 06 3.1. Placement and mounting 06 3.2. Mains connection 06 3.3. Multi-function 07 3.4. Input connections 08 3.5. Input options 09 3.6. Output connections 10 3.7. Output options 11 4. Operation and usage 11 4.1. Start up 1...
Page 4
4 1. Important remark congratulations! You are the owner of a carefully designed and manufactured equipment. We thank you for having purchased our mpa r power amplifier. It is very important that you read this manual before connecting the amplifier in order to obtain its maximum performance. We reco...
Page 5
5 mpa6-80r the mpa6-80r amplifier station consists of six 85w/4 amplifiers which can be configured through a set of switches found on the rear panel. This allows multiple amplification setups useful in many situations, for example: six mono amplifiers for six different mono inputs. When setup t...
Page 6
6 3. Installation 3.1. Placement and mounting the amplifier is presented as a 2 unit high 19'' rack module. It is supplied with plastic washers in order not to damage the unit when tightening the screws. Always fix the amplifier to a 19” rack through the front ears using all corners and four screws....
Page 7
7 3.3. Multi-function depending on the input switches on the mpa r (28, 29, 30, 31, 32, 33, 40, 41, 42) located on the rear panel, four different amplification configurations can be achieved: mpa4-80r mpa6-80r - 4 mono amplifiers with following possibilities: - 6 mono amplifiers with following possi...
Page 8
8 3.4. Input connections the signal input connections (34, 35, 36, 37, 38, 39) are electronically balanced xlr-3 sockets, with input impedance higher than 20k and a nominal sensitivity of 0dbv(1v). Pin assignment: 1. Ground 2. Phase (in phase with the output) 3. Non phase (inverted phase) the foll...
Page 9
9 3.5. Input options option mpa4-80r mpa6-80r 1 mono 4 mono amplifiers for 4 different mono signal 6 mono amplifiers for six different mono signal 2 mono 4 mono amplifiers for a common mono input 6 mono amplifiers for a common mono input 3 mono 4 mono amplifiers for a common stereo input 6 mono ampl...
Page 10
10 3.6. Output connections the outputs section at the rear panel has screwable terminals (43, 44, 45, 46, 47, 48), one for each amplifier. The attenuation controls and the output configurations are described later in paragraph 3.7. The cable which connects the speakers to the amplifier should be hig...
Page 11
11 3.7. Output options option mpa4-80r mpa6-80r 1 mono 4 mono amplifiers 6 mono amplifiers 2 stereo 2 stereo amplifiers 3 stereo amplifiers 3 bridged 2 bridged amplifiers 3 bridged amplifiers 4 combination 1 bridged amplifier and 2 mono amplifiers for a common mono input 1 bridged amplifier and 4 mo...
Page 12
12 4.2. Input attenuation these are rotary trimmers located on the front panel (1, 2, 3, 4, 5, 6). These attenuators allow the connection of different mixers, an independent volume control and the connection of speakers not able to handle the amplifiers maximum output power, thus avoiding the risk o...
Page 13
13 4.4. Connection of the vca control as already mentioned in the introduction of this manual, the signal attenuation level for each of the input channels can be set using the following methods: a) using a remote potentiometer with nominal resistance between 10k and 50k. B) using a device that ge...
Page 14
14 6. Diagrams 6.1. Function list 1. Channel 1 volume, ch1 2. Channel 2 volume, ch2 3. Channel 3 volume, ch3 4. Channel 4 volume, ch4 5. Channel 5 volume, ch5 6. Channel 6 volume, ch6 7. Input 1 signal presence, sp 8. Input 2 signal presence, sp 9. Input 3 signal presence, sp 10. Input 4 signal pres...
Page 15
15 6.2. Function diagram.
Page 16
16 explicación de los símbolos gráficos el símbolo del relámpago con una flecha en la punta y dentro de un triangulo equilátero, tiene el propósito de alertar al usuario de la presencia de un voltaje peligroso y sin aislar dentro del aparato, y de una magnitud tal que puede constituir riesgo de desc...
Page 17
17 manual de instrucciones 1. Nota importante 18 2. IntroducciÓn 18 3. InstalaciÓn 20 3.1. Ubicación y montaje 20 3.2. Conexión a red 20 3.3. Multifunción 21 3.4. Conexiones de entrada 22 3.5. Opciones de entrada 23 3.6. Conexiones de salida 24 3.7. Opciones de salida 25 4. OperaciÓn y uso 25 4.1. P...
Page 18
18 1. Nota importante ¡enhorabuena!. Vd. Posee el resultado de un cuidadoso diseño y una esmerada fabricación. Agradecemos su confianza por haber elegido nuestra etapa de potencia mpa r. Para conseguir la máxima operatividad del aparato y su máximo rendimiento, es muy importante antes de su conexión...
Page 19
19 mpa6-80r la mpa6-80r está formada por seis amplificadores de 85w/4 configurables mediante los conmutadores situados en el panel posterior, permitiendo múltiples posibilidades de trabajo de entre las que destacamos: 6 amplificadores en mono para 6 señales mono diferentes. De esta forma el mpa...
Page 20
20 3. InstalaciÓn 3.1. Ubicación y montaje el amplificador se presenta en módulo rack de 19" y dos unidades de altura, se suministra con arandelas de plástico con el fin de poderlo montar en un rack sin dañar el aparato. Fije siempre el amplificador al rack de 19” a través de las orejas frontales me...
Page 21
21 3.3. Multifunción en el mpa r según la posición de los conmutadores de entrada (28, 29, 30, 31, 32, 33, 40, 41, 42) situados en el panel posterior dispondremos de 4 funciones diferentes de amplificación: mpa4-80r mpa6-80r - 4 amplificadores en mono, con posibilidad de: - 6 amplificadores en mono,...
Page 22
22 3.4. Conexiones de entrada las entradas de señal (34, 35, 36, 37, 38, 39) son del tipo xlr-3 balanceadas electrónicamente, con una impedancia de entrada superior a 20k y una sensibilidad nominal de 0dbv(1v). La asignación es la siguiente: 1.- ground (masa) 2.- phase (señal en fase con la salida...
Page 23
23 3.5. Opciones de entrada opciÓn mpa4-80r mpa6-80r 1 mono 4 amplificadores en mono para 4 entradas mono diferentes 6 amplificadores en mono para 6 entradas mono diferentes 2 mono 4 amplificadores en mono con una entrada común 6 amplificadores en mono con una entrada común 3 mono 4 amplificadores e...
Page 24
24 3.6. Conexiones de salida la sección outputs del panel posterior está provista de regletas atornillables (43, 44, 45, 46, 47, 48), una por amplificador. Los controles de atenuación y conexionado de las salidas se detallan en el apartado 3.7. El cable de conexión que une las salidas del amplificad...
Page 25
25 3.7. Opciones de salida opciÓn mpa4-80r mpa6-80r 1 mono 4 amplificadores en mono 6 amplificadores en mono 2 estéreo 2 amplificadores estéreo 3 amplificadores estéreo 3 puente 2 amplificadores en puente 3 amplificadores en puente 4 combinado 1 amplificador en puente y 2 amplificadores mono con una...
Page 26
26 4.2. Atenuadores de entrada están constituidos por sendos potenciómetros rotativos, situados en el panel frontal (1, 2, 3, 4, 5, 6). Estos atenuadores posibilitan la conexión a distintos tipos de mesas, regulación de nivel independiente y conexión de altavoces que soporten una potencia inferior a...
Page 27
27 4.4. Conexionado del control vca tal y como se menciona en la introducción de este manual, el nivel de atenuación de señal para cada uno de los canales de entrada puede ser fijado mediante: a) el uso de un potenciómetro remoto, de valor nominal comprendido entre 10k y 50k. B) dispositivo gener...
Page 28
28 6. Diagramas 6.1. Lista de funciones 1. Volumen canal 1, ch1 2. Volumen canal 2, ch2 3. Volumen canal 3, ch3 4. Volumen canal 4, ch4 5. Volumen canal 5, ch5 6. Volumen canal 6, ch6 7. Indicador de presencia de señal en la entrada 1, sp 8. Indicador de presencia de señal en la entrada 2, sp 9. Ind...
Page 29
29 6.2. Diagrama de funciones.
Page 30
30 explication des symboles graphiques le symbole d'éclair avec une flèche, à l'intérieur d'un triangle équilatéral, avertit l'utilisateur de la présence de « tension dangereuse », non isolée, à l'intérieur de l'enceinte du produit, assez importante pour constituer un risque d'électrocution des pers...
Page 31
31 notice d’utilisation 1. Note importante 32 2. Introduction 32 3. Installation 34 3.1. Situation et montage 34 3.2. Branchement 34 3.3. Multifonction 35 3.4. Branchement de l'entrée du signal 36 3.5. Options d’entrée 37 3.6. Branchement de sortie 38 3.7. Options de sortie 39 4. Mise en marche et u...
Page 32
32 1. Note importante félicitations ! Vous avez en votre possession le résultat d’un design et d’une fabrication particulièrement soignée. Nous vous remercions de la confiance que vous nous portez en choisissant notre amplificateur mpa r. Pour obtenir le meilleur résultat de cet appareil, il est imp...
Page 33
33 mpa6-80r l’unité d’amplification mpa6-80r comprend six amplificateurs de 85w/4 , configurables par les commutateurs situés sur la façade arrière de l’amplificateur, et permet de travailler de plusieurs façons: 6 amplificateurs mono avec 6 entrées mono différentes. De cette façon, le mpa r peu...
Page 34
34 3. Installation 3.1. Situation et montage l’amplificateur est présenté en rack 19" de deux unités de hauteur. Pour éviter de marquer les oreilles de l’amplificateur lors de la mise en rack, des rondelles en plastique sont fournies avec l’amplificateur. Fixez toujours l'amplificateur sur un rack 1...
Page 35
35 3.3. Multifonction grâce au commutateur d’entrée sur le mpa r (28, 29, 30, 31, 32, 33, 40, 41, 42) situé sur la façade arrière, nous avons 4 possibilités différentes d’amplification : mpa4-80r mpa6-80r - 4 amplificateurs mono avec les possibilités suivantes: - 6 amplificateurs mono avec les possi...
Page 36
36 3.4. Branchement de l'entrée du signal les entrées du signal (34, 35, 36, 37, 38, 39) sont de type symétriques xlr-3 avec une impédance d’entrée supérieure à 20k et une sensibilité nominale de 0dbv(1v). L’assignation est la suivante: 1.- masse (ground) 2.- phase ou point chaud (signal en phase ...
Page 37
37 3.5. Options d’entrée option mpa4-80r mpa6-80r 1 mono 4 amplificateurs mono pour 4 signaux mono différents 6 amplificateurs mono pour 6 signaux mono différents 2 mono 4 amplificateurs mono pour 1 entrée mono commune 6 amplificateurs mono pour 1 entrée mono commune 3 mono 4 amplificateurs mono pou...
Page 38
38 3.6. Branchement de sortie la section de sortie (outputs) de la face arrière est pourvue de borniers vissables (43, 44, 45, 46, 47, 48), un par amplificateur. Les contrôles d’atténuation et les branchements de sortie sont décrits plus loin dans le paragraphe 3.7. Le câble de raccordement de l'amp...
Page 39
39 3.7. Options de sortie option mpa4-80r mpa6-80r 1 mono 4 amplificateurs mono 6 amplificateurs mono 2 stéréo 2 amplificateurs stéréo 3 amplificateurs stéréo 3 bridgé 2 amplificateurs bridgés 3 amplificateurs bridgés 4 combinaisons 1 amplificateur bridgé et 2 amplificateurs mono pour une 1 entrée m...
Page 40
40 4.2. Atténuateurs d'entrée ils se présentent sous la forme d'un potentiomètre rotatif situés sur le panneau de commandes (1, 2, 3, 4, 5, 6). Ces atténuateurs permettent de connecter différentes consoles de mixage, de régler le volume de façon indépendante et de brancher des hp pouvant supporter u...
Page 41
41 4.4. Connexion du vca de contrôle comme mentionné au début de ce manuel, le niveau d'atténuation du signal pour chaque canal d'entrée peut être fixé au moyen : a) de l'utilisation d'un potentiomètre distant, de valeur nominale comprise entre 10k et 50k. B) d'un dispositif générateur d'un signa...
Page 42
42 6. SchÉmas 6.1. Liste de fonctions 1. Volume canal 1, ch1 2. Volume canal 2, ch2 3. Volume canal 3, ch3 4. Volume canal 4, ch4 5 volume canal 5, ch5 6. Volume canal 6, ch6 7. Indicateur de présence du signal en entrée 1, sp 8. Indicateur de présence du signal en entrée 2, sp 9. Indicateur de prés...
Page 43
43 6.2. Schéma de fonctionnement.
Page 44
44 erklärung der grafischen darstellungen das blitzsymbol mit dem pfeil innerhalb eines gleichseitigen dreiecks soll den benutzer vor nicht isolierter „gefährlicher spannung” innerhalb des produktgehäuses warnen, die hoch genug ist, um einem menschen einen elektrischen schlag zu versetzen. Das ausru...
Page 45
45 bedienungsanleitung 1. Wichtige vorbemerkung 46 2. EinfÜhrung 46 3. Installation 48 3.1. Aufstellungsort und montage 48 3.2. Anschluss an das netz 48 3.3. Multifunktion 49 3.4. Eingangsanschlüsse 50 3.5. Eingangsmöglichkeiten 51 3.6. Ausgangsanschlüsse 52 3.7. Ausgangsmöglichkeiten 53 4. Bedienun...
Page 46
46 1. Wichtige vorbemerkung herzlichen glückwunsch! Sie besitzen hiermit ein hochwertiges gerät als ergebnis eines großen entwicklungsaufwandes und sorgfältiger fertigungsplanung. Wir bedanken uns für ihr vertrauen, einen ecler mpa r gewählt zu haben. Bitte lesen sie alle erläuterungen in dieser bed...
Page 47
47 mpa6-80r die verstärkungsstation mpa6-80r besteht aus sechs 85w/4 verstärkern, die durch wahlschalter an der rückseite des geräts konfiguriert werden können. Dies ermöglicht verschiedenste arbeitsmöglichkeiten, wie zum beispiel: 6 mono-verstärker für 6 verschiedene mono-signale. Der mpa r is...
Page 48
48 3. Installation 3.1. Aufstellungsort und montage der verstärker ist im 19'' rackformat konzipiert und ist zwei he hoch. Es werden für den einbau in ein rack plastikringe mitgeliefert, um das gerät nicht zu beschädigen. Befestigen sie den verstärker immer beim fronteinbau mit vier schrauben an all...
Page 49
49 3.3. Multifunktion bei dem mpa r verfügen sie über vier verschiedene verstärkungskonfigurationen, je nachdem wie die eingangswahlschalter an der rückseite des geräts (28, 29, 30, 31, 32, 33, 40, 41, 42) eingestellt sind. Mpa4-80r mpa6-80r - 4 mono-verstärker mit folgenden möglichkeiten: - 6 mono-...
Page 50
50 3.4 eingangsanschlüsse die eingangsbuchsen des mpa r (34, 35, 36, 37, 38, 39) sind elektronisch symmetrierte xlr-buchsen mit einer eingangsimpedanz von >20k und einer nennempfindlichkeit von 0dbv(1v). Die pinbesetzung ist: 1. Ground (masse) 2. Phase (phasengleich bezüglich ausgang) 3. Non phase...
Page 51
51 3.5. Eingangsmöglichkeiten option mpa4-80r mpa6-80r 1 mono 4 mono-verstärker für 4 verschiedene mono-signale 6 mono-verstärker für 6 verschiedene mono-signale 2 mono 4 mono-verstärker für ein gemeisames mono-signal 6 mono-verstärker für ein gemeisames mono-signal 3 mono 4 mono-verstärker für ein ...
Page 52
52 3.6. Ausgangsanschlüsse der bereich outputs an der rückseite ist mit verschraubbaren kabelanschlüsse (43, 44, 45, 46, 47, 48) ausgestattet. Die verschiedenen ausgangskonfigurationen werden in paragraph 3.7. Beschrieben. Das kabel, welches den verstärker mit den lautsprechern verbindet, sollte hoc...
Page 53
53 3.7. Ausgangsmöglichkeiten option mpa4-80r mpa6-80r 1 mono 4 mono-verstärker 6 mono-verstärker 2 stereo 2 stereo-verstärker 3 stereo-verstärker 3 Überbrückt 2 verstärker im brückenbetrieb 3 verstärker im brückenbetrieb 4 kombination 1 verstärker im brückenbetrieb und 2 mono-verstärker für ein gem...
Page 54
54 4.2. Eingangs-trimmer es handelt sich um drehbare potentiometer, welche an der vorderseite des gerätes angebracht sind. (1, 2, 3, 4, 5, 6). Diese trimmer ermöglichen den anschluss verschiedener mischpulte oder vorverstärker, unabhängige volume-regelug pro kanal und den anschluss von lautsprechern...
Page 55
55 4.4. Anschluss der vca steuerung wie schon während der einleitung dieses handbuchs erwähnt, kann der dämpfungsgrad eines jeden eingangssignals folgendermassen festgelegt werden: a) durch verwendung eines entferten spannungsteilers, dessen nominalwert sich zwischen 10k und 50k befindet. B) dur...
Page 56
56 6. Diagramme 6.1. Funktionsliste 1. Volume kanal 1, ch1 2. Volume kanal 2, ch2 3. Volume kanal 3, ch3 4. Volume kanal 4, ch4 5. Volume kanal 5, ch5 6. Volume kanal 6, ch6 7. Anwesenheit des eingangssignals 1, sp 8. Anwesenheit des eingangssignals 2, sp 9. Anwesenheit des eingangssignals 3, sp 10....
Page 57
57 6.2. Funktionsdiagramm.
Page 58
58 6.3. Configuration diagram 6.3. Diagrama de configuración 6.3. Schéma de configuration 6.3. Konfiguration diagramm.
Page 59
59 6.4. Technical characteristics 6.4. Características técnicas 6.4. Caractéristiques techniques 6.4. Technische daten power 20-20khz 1% thd mpa4-80r mpa6-80r 1 channel @ 4 80 wrms 85 wrms 1 channel @ 8 50 wrms 52 wrms all channels @ 4 55 wrms 58 wrms all channels @ 8 40 wrms 48 wrms 1 bridged chann...
Page 60
6.5. Block diagram 6.5. Diagrama de bloques 6.5. Blocs de diagrammes 6.5. Blockschaltbild ecler laboratorio de electro-acústica s.A. Motors 166-168, 08038 barcelona, spain internet http://www.Ecler.Com e-mail: info@ecler.Es 50.0212.01.04.