1. DL manuals
  2. Eclipse
  3. Car Stereo System
  4. ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420
  5. Owner's Manual

Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 Owner's Manual

Summary of ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420

  • Page 1

    Owner's manual we appreciate your purchase of this receiver. Please read through this manual for correct operation. We suggest that after reading it you keep this manual in a safe place for future reference. Model 54420 by fujitsu ten r esn e3 high-power cd receiver with cdc/e-com/dsp control and wi...

  • Page 2: For Your Safety In Using The

    2 for your safety in using the 54420 warnings and caution signs, illustrated below, are posted throughout this manual as well as on the 54420. They show safe and correct ways to handle the product so as to prevent personal injury to you and others and avoid damage to property. Before reading through...

  • Page 3: Caution

    3 • do not place the vinyl storage bag over a person. It may cause a serious accident or death by suffocation. • do not adjust the controls while driving the car. To adjust the controls, stop the car in a safe location. • to prevent accidents, store batteries for the remote control out of the reach ...

  • Page 4: Caution

    4 • do not stick your fingers or hands into the disc slot. Doing so may cause personal injury. • this product must be operated only as on-board equipment, or it may cause electrical shock or injury. • do not play distorted sounds for long periods of time; the speakers may overheat and cause a fire. ...

  • Page 5: Table of Contents

    5 table of contents operating precautions ................................................ 8 notes on operation ........................................................................ 8 about compact discs .................................................................... 9 about cleaning a cd .....

  • Page 6

    6 how to operate the tuner .......................................... 31 tuning to a station ....................................................................... 31 entering stations into memory automatically (the automatic preset mode: asm) ............................................. 32 manual...

  • Page 7

    7 if you have a question: .............................................. 60 displaying information (for troubleshooting) .................................. 61 specifications ............................................................ 64 before installation .............................................

  • Page 8: Notes On Operation

    Operating precautions 8 notes on operation ٟ operating precautions handling and care.> • for your safety, play only at volume levels that allow outside sounds to be heard. • use only audio compact discs. This player can only play compact discs bearing the logo shown to the left. • do not insert anyt...

  • Page 9: About Compact Discs

    9 operating precautions • the signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound quality or intermittent playback. Observe the following precautions to ensure high quali...

  • Page 10

    Operating precautions 10 about cd accessories • do not use accessories (stabilizers, protective seals, laser lens cleaners, etc.) sold for “ improving sound performance” or “ protecting cds.” the changes in cd thickness or outside dimensions made by these accessories may cause problems in the player...

  • Page 11: About Cleaning A Cd

    11 operating precautions about irregularly-shaped cds • specially-shaped cds, like heart- shaped or octagonal cds, cannot be played. Do not attempt to play them, even with an adapter, since they may damage the player. • use a commercially available compact disc cleaner to clean a cd, wiping lightly ...

  • Page 12: Front View

    ٟ names of controls and parts front view ※note：double function button→"e-com"&"mute" functions names of controls and parts 12 12 12 [cd] button buttons [1] to [6] [pwr] button [ disc ] buttons [audio control] button [ ] buttons [func] button [fm ･am] button [asm] button [disp] button [e-com] button ...

  • Page 13: Procedure

    13 esn (key cd) security operating procedure ٟ esn (key cd) security operating procedure ع how to program the key cd 1 . Turn the vehicle’s ignition on. Press the [pwr] button or [fm• am] button to activate the tuner mode. The tuner is now turned on. 2 . Press and hold button [1], then the [fm• am] ...

  • Page 14: 1 .

    Esn (key cd) security operating procedure 14 • if there is a problem with the inserted cd, an [err] message will appear for two seconds and the cd will be ejected. Reinsert the ejected cd. • if a cd causes the [err] message to appear twice in a row, a [change] message will appear for two seconds. Tr...

  • Page 15: 1 .

    15 esn (key cd) security operating procedure • this process cancels the protection for the esn deck. • if power to the 54420 is disconnected, then reconnected, a key cd will not need to be inserted in order to return the unit to normal operation. • inserting a cd other than the key cd will not cance...

  • Page 16: 1 .

    Esn (key cd) security operating procedure 16 ع how to resume normal operation (esn security lock out) if power to the 54420 is disconnected while esn security is active (a key cd was programmed), operation is disabled until power is restored and the unit unlocked. Follow this procedure to resume nor...

  • Page 17: 1 .

    17 esn (key cd) security operating procedure ع what happens if an incorrect cd is inserted? 1 . An [err_] message will be appear, then change to a flashing [disc], then the cd will be ejected. You will have five uninterrupted attempts to insert the correct cd. 2 . After the 5 th incorrect attempt, t...

  • Page 18: 1 .

    Esn (key cd) security operating procedure 18 ع how to turn the security indicator on/off once esn security is activated, the indicator flashes whenever the vehicle’s ignition is turned off, warning potential thieves that the unit is protected. However, if you do not want this visible deterrent, it m...

  • Page 19: ٟ Basic Operation

    19 basic operation [fm ･am] button [ ] buttons [pwr] button ٟ basic operation this section covers basic operating procedures.For additional details, please refer to the sections on specific functions. ع turning the power on and off 1 . Press the [pwr] button. Pressing the button turns the power on a...

  • Page 20: ع Listening to The Tuner

    Basic operation 20 ع listening to the tuner 1 . Press the [fm• am] button. This will turn the tuner on. To turn the tuner off, either press the [pwr] button or select another mode. 2 . Tap the [fm• am] button to switch to the desired fm or am bands. Each additional tap of the button switches the pre...

  • Page 21: 1 .

    21 basic operation [disp] button button [6] [func] button ع adjusting audio volume 1 . Turn the [audio control] button to the left or right. Turn to the left : decreases the volume. Turn to the right : increases the volume. • press and hold the [e-com] button for more than two seconds to activate or...

  • Page 22: Operation)

    Basic operation 22 ع others ٕ ٕdisabling the guide tone feature (for button operation) the receiver is set at the factory to emit a beep tone in response to button operation. The guide tone feature may be disabled in the following procedure: 1 . Press and release the [func] button. 2. Press and hold...

  • Page 23: ٕsetting The Clock

    23 basic operation [audio control] button ٕ ٕsetting the clock this receiver uses the 12-hour, a.M./p.M.Display notation. 1 . Press the [disp] button repeatedly to switch to the clock display mode. 2 . To adjust the hour, press either button [1] or [2] while holding the [disp] button down. Button [1...

  • Page 24

    Basic operation 24 ٕ ٕswitching audio control modes various audio control modes may be fine-tuned using this procedure. 1 . Press the [audio control] button for less than one second. Pressing the button repeatedly will allow you to control adjustments of [bass] (low frequencies), [treb] (high freque...

  • Page 25: ٕswitching Non-Fader Modes

    25 basic operation ٕswitching non-fader modes 1 . Press the [func] button. 2 . Press button [5] to switch the phase. 3 . Press the [func] button. Pressing the button will cancel function mode. ٕ ٕdisabling the tone control cancel feature 1 . Press the [func] button. 2 . Press the [asm] button to swi...

  • Page 26: 1 .

    How to operate the cd player 26 ٟ how to operate the cd player first press the [cd] button to switch to the disc mode. It is assumed here that a cd has already been loaded into the unit. ع listening to cds 1 . Press the [cd] button. This turns on the disc mode and starts cd play. If an external cd c...

  • Page 27: 1 .

    27 how to operate the cd player ع advancing to the next track or returning to the beginning of the track being played 1 . Press the [ ] button. [ ] button: advances to the next track. [ ] button: returns to the beginning of the track being played. • pressing and holding the [ ] button will fast-forw...

  • Page 28: 1 .

    How to operate the cd player 28 ع repeating the same track (repeat) 1 . Press button [5 (rpt)] to repeat the track being played. To cancel, press button [5] again. ع playing tracks in random order (random) 1 . Press button [6 (rand)] to play the tracks in random order. To cancel, press button [6] ag...

  • Page 29: 1 .

    29 how to operate the cd player ع ejecting the disc 1 . Press the [ （eject）] button. [ （eject）] button.

  • Page 30: 1 .

    How to operate the cd player 30 ع displaying a genre for a cds a preset genre can be assigned to individual cd and displayed when they are played. 1 . Press the [disp] button until a preset genre is displayed. 2 . Press button [1] nine genre are available for a cd in the following sequence; 1.Jazz 2...

  • Page 31: ٟ How to Operate The Tuner

    31 how to operate the tuner ٟ how to operate the tuner first, press the [fm• am] button to start tuner operation. There are automatic and manual methods for setting stations in memory. The receiver will accept up to 24 stations in memory: six in am and 18 in fm (6 each for fm1, fm2 and fm3.) ع tunin...

  • Page 32: 1 .

    How to operate the tuner 32 • at times, it may be difficult to maintain optimum reception because the antenna affixed to your vehicle is in motion constantly (relative to the broadcast antenna), encountering continuous variation in the received radio signals’ strength. Other factors affecting recept...

  • Page 33: 1 .

    33 how to operate the tuner • press any numbered button to select the station whose frequency is indicated right above the button. • when a new station is set in memory, the station previously set in memory will be deleted. • if the number of receivable stations fewer than six, the stations set in t...

  • Page 34: 1 .

    How to operate the tuner 34 ع preset station scan this function enables reception of all the stations in the numbered preset buttons for five seconds each. 1 . Press the [asm] button. [p• scan] will appear at the top of the display, and stations stored under preset buttons [1] through [6] will bepla...

  • Page 35: 1 .

    35 how to operate the tuner ع fm reception characteristics in general, fm has much better tonal quality than am. However, fm and fm stereo reception encounter several characteristic problems not encountered with am. Fm is more difficult to receive than am in a moving vehicle. The following are expla...

  • Page 36: 3 .

    How to operate the tuner 36 3 . Reception area of fm broadcasts a home receiver can catch weak fm stereo signals through the use of a tall, directional or ultra-sensitive antenna. In a moving vehicle, the area for good reception is limited because of varying conditions encountered while driving, inc...

  • Page 37: 4 .

    37 how to operate the tuner 4 . Multipath the reflection characteristics of fm waves cause another problem called multipath– fm wave signals reflecting off of buildings, mountains, etc. When the antenna receives direct and reflected waves at the same time, distortion of sound in the treble range oft...

  • Page 38: Control

    How to use the card remote control 38 ٟ how to use the card remote control • be careful when handling the control, especially because it is small and light. Dropping or striking it hard may damage it, wear out the battery or cause a malfunction. • keep the remote control free of moisture, dust and w...

  • Page 39: ع Turning The Power On/off

    39 how to use the card remote control ع turning the power on/off 1 . Press the [pwr] button. The power turns on or off each time the button is pressed. • when the main unit is shut down, the remote control will not work. ع adjusting the audio volume 1 . Press the [+] or [-] button. [+] button: incre...

  • Page 40: ع How to Play The Tuner

    How to use the card remote control 40 ع how to play the tuner enter the tuner mode first. ٕ ٕselect the fm/am band 1. Tap the [band] button. Each tap will switch tuner modes from fm1 → fm2 → fm3 → am. ٕ ٕselect a station (manually or automatically) a short tap of the button will allow manual station...

  • Page 41: ٕswitching Disc Modes

    41 how to use the card remote control ع how to play cds select the disc mode first. ٕ ٕadvancing to the next track or returning to the beginning of the track being played 1. Press the [ track• aps ] button. [ ] button: skips to the next track. [ ] button: returns to the beginning of the track being ...

  • Page 42: 1 .

    How to use the card remote control 42 ع replacing the battery use one cr2025 battery. 1 . On the back of the remote control, while pressing the locking knob on the battery slot cover toward your right, pull out the battery carier with your fingernail. 2 . Remove the old battery, then place the new o...

  • Page 43: Remote Control

    43 how to use an optional nob remote control ٟ how to use an optional nob remote control ع turning the power on/off 1 . Press the [pwr] button. The power turns on or off each time the button is pressed. • when the main unit is shut down, the remote control will not work. ع adjusting the audio volume...

  • Page 44: 1 .

    How to use an optional nob remote control 44 ع switching playback modes 1 . Press the [mode] button. Tap the button to switch modes in the following sequence: ع how to play the tuner enter the tuner mode first. ٕ ٕselect the fm/am band 1. Tap the [band] button. Each tap will switch tuner modes from ...

  • Page 45: ٕselecting Preset Stations

    45 how to use an optional nob remote control ٕ ٕselecting preset stations a total of six stations may be selected (preset tuning) out of those already set in memory through the main unit. (refer to “ manually setting stations into memory,” page 33.) 1. Press the [ disc ] button. [ ] button: tunes th...

  • Page 46: ٕswitching Disc Modes

    How to use an optional nob remote control 46 (previous) disc. ٕ ٕswitching disc modes 1. Press the [band] button. When the cd changer is connected, tap the [band] button to change modes from cd player → cd changer 1 → cd changer 2. The indicator will skip a changer or player that has no disc loaded ...

  • Page 47: 1 .

    47 how to use an optional nob remote control ع replacing the battery use two aa cell batteries. 1 . Remove the back cover of the remote control unit by gently pressing and sliding it in the direction indicated by the arrow. 2 . Install the two batterles provided into the compartment as illustrated i...

  • Page 48: ● Caution ●

    How to use an optional nob remote control 48 ● caution ● ・be extremely careful not to swallow the battery. ・the battery life is approximately one year. If the remote control unit does not operate correctly or if the button lump gets dim, replace the batteries. ・be sure to orlent the batteries correc...

  • Page 49: ٕlistening to A Cd

    49 how to operate the receiver with an optional cd changer connected ٟ how to operate the receiver with an optional cd changer connected ع basic operation this section covers the operation of the cd changer that is connected to the receiver. To switch from another mode, press the [cd] button. ٕ ٕlis...

  • Page 50

    How to operate the receiver with an optional cd changer connected 50 ٕplaying the beginning of tracks (scan): 1. Press button [4 (scan)]. Tapping the button causes the changer to move up to the next track and play it for 10 seconds, then move up to the next track and play it for 10 seconds, and so o...

  • Page 51: ٕspecifying A Cd to Play

    51 how to operate the receiver with an optional cd changer connected • occasionally the same track happens to be played (selected) two or more times in a row, but it is no sign of a problem. • when any of the functions - “ playing the beginning of tracks,” “ repeating the same track” and “ playing t...

  • Page 52: 1 .

    How to operate the receiver with an optional cd changer connected 52 ع displaying a genre for a cds a preset genre can be assigned to individual cd and displayed when they are played. 1 . Press the [disp] button until a preset genre is displayed. 2 . Press button [1] nine genre are available for a c...

  • Page 53: 1 .

    53 how to operate the receiver with an optional dsp/eq unit connected ٟ how to operate the receiver with an optional dsp/eq unit connected ع how to operate the dsp functions the dsp feature adds reverberations to simulate ambience in different types of surroundings (room sizes). 1 . After pressing t...

  • Page 54

    How to operate the receiver with an optional dsp/eq unit connected 54 • the following six patterns are preset at the factory: ٕ ٕfine-tuning an individual roomsize mode detailed adjustments are available in any of the room size modes. 1. After pressing the [func] button, hold button [1] down for mor...

  • Page 55

    55 how to operate the receiver with an optional dsp/eq unit connected 2. Tap button [audio control] to select the desired mode of adjustment. The mode sequence on the button is as follows: 3. Turn the [audio control] button. This button adjusts the reverberation level and duration. Right: increases ...

  • Page 56

    How to operate the receiver with an optional dsp/eq unit connected 56 5. Push the [func] button. The adjustment mode will be canceled and the selected room size will now take effect. ٕ ٕretrieving a preset pattern from memory press a preset button to retrieve the room size in memory. The buttons und...

  • Page 57: ٕswitching Equalizer Modes

    57 how to operate the receiver with an optional dsp/eq unit connected ع how to operate the eq functions the eq functions enable level adjustments of various frequency groups for optimum listening conditions with a specific kind of music or musical instrument. ٕ ٕswitching equalizer modes 1. After pr...

  • Page 58: ٕfine-Tuning Eq Functions

    How to operate the receiver with an optional dsp/eq unit connected 58 ٕfine-tuning eq functions 1. After pressing the [func] button, hold button [2] down for more than one second. The eq adjustment mode starts. 2. Tap button [2] until the desired equalizer mode is displayed. 3. Tap the [audio contro...

  • Page 59

    59 how to operate the receiver with an optional dsp/eq unit connected ٕretrieving an equalizer mode from memory press a preset button to retrieve the equalizer mode set in memory for the button. The buttons that set equalizer modes in memory are called preset buttons. 1. After pressing the [func] bu...

  • Page 60: ٟ If You Have A Question:

    If you have a question: 60 ٟ if you have a question: first check the items mentioned below before attempting to troubleshoot problems. ٨ caution ٨ • if a problem occurs, for instance when the unit does not respond to any button presses, or the display doesn't work press the reset button using a shar...

  • Page 61

    61 if you have a question: ع displaying information (for troubleshooting) the information listed in the chart below is displayed to show the status of the cd player and cd changer. Refer to the chart for the appropriate action. Infomation code table when info flash on the indicator . Nos.2-7 are dis...

  • Page 62

    If you have a question: 62 dead or weak sound power does not turn on. Frequencies or titles set in memory are deleted. No guide tone sounds. The remote control does not work. Common to all is the volume control up sufficiently? Is the muting function in effect (mute)? Is the fader or balance control...

  • Page 63

    63 if you have a question: problem causes remedial action to take receives no stations, or receives static noise. Extend the antenna. Tune to a station. Tune to a local station. (please note, there may be no local stations servicing the area where you are currently driving.) avoid operating such equ...

  • Page 64: ٟ Specifications

    Specifications 64 ٟ specifications general > power supply 14.4vdc (11-16v) current drain 3a (1w) dimensions (w x h x d) in-dash unit 7 ″×2″×6-1/8″(178×50×155mm) fm tuner > frequency range 87.75~107.9mhz (200khz step) usable sensitivity 13dbf 50db quieting sensitivity 16dbf frequency response 30~15 ,...

  • Page 65

    65 specifications cd section > frequency response 20~20,000hz wow & flutter below measurable limits stereo separation 64db s/n ratio (a-weighted) 94db dynamic range 90db total harmonic distortion 0.03% (1khz) audio amplifier > power output 20w ×4 (20~20,000hz,1.0% thd , 4 Ω) max .40w×4 output level/...

  • Page 66: ٟ Before Installation

    Before installation 66 ٟ before installation notes be sure to disconnect the battery negative terminal before installing the receiver. ع components no. Item q'ty 1 main unit 1 2 mounting sleeve 1 3 side bracket 2 4 rear bracket 1 5 bezel 1 6 bushing 1 7 self-tapping screw (6 x 16 mm) 2 8 stud bolt 1...

  • Page 67: ٟ Mounting Instruction

    67 mounting instruction ٟ mounting instruction ع mounting the main unit 1 . Insert the mounting sleeve into the opening in the vehicle console. 2 . Use a screwdriver or the like to bend the tabs in the mounting sleeve to secure the mounting sleeve . 3 . Attach the side brackets to the main unit usin...

  • Page 68: 4 .

    Mounting instruction 68 4 . Mount the stud bolt to the main unit. 5 . Insert the main unit into the mounting sleeve until it locks in place. 6 . Fasten the rear of the main unit using either method [a] or [b]. Select method [a] or [b] to suit the interior configuration of the vehicle. 7 . Install th...

  • Page 69: Notes

    69 mounting instruction notes to prevent unconnected leads from shorting out, insulate them by wrapping their tips with electrical tape. Similarly, insulate the ends of connected leads. If an external amplifier is to be connected to the receiver, be sure to ground its outside housing to the vehicle ...

  • Page 70

    Mounting instruction 70

  • Page 71: ع System

    71 mounting instruction ع system.

  • Page 72

    Mounting instruction 72 red fl fr rl rr y ellow blue orange/white blue/white black 14.

  • Page 73

    73 mounting instruction 14.

  • Page 74

    Mounting instruction 74.

  • Page 75: Important

    75 mounting instruction important record your “ key cd” here… store your “ key cd” along with your owner’s manual in your sock drawer..

  • Page 76

    By fujitsu ten r division of fujitsu ten corp. Of america 19600 south vermont avenue, torrance, ca 90502 (310) 327-2151 090001-13810700 9912de(n.O.) customer notice please retain this booklet and write in the serial number of your 54420 for identification. The serial number is labeled or stamped on ...