Eco GEMINI Instruction Manual - page 4
1. My Gemini seems to have lost its signal, how do I get it back?
If your Gemini seems to not be responding to changes made via
Smartphone, it may need to be set up again. Page 2 details this
process. If you cannot find the ECO-XXXX in your WiFi setup, you may
have to RESET the Gemini to factory settings. This process is detailed
on page 1 of this guide.
2. Can I program this at home/office on my WIFI then take it to
the field and have it work there automatically?
Unfortunately, the Gemini WILL NOT work if you setup the device
previous to bringing it to where it will be used. It will default to
looking for the previously setup WiFi or try to connect to a new
WiFi signal there. If NO WiFi signal is present, it will perform the
previosuly setup timers.
3. What types of Transformers does it fit in?
The GEMINI fits into MOST traditional low voltage lighting
transformers.
4. Will it still work in a closed stainless steel transformer?
The GEMINI will work in an enclosed stainless steel transformer.
However, it may diminish the signal from your router to the GEMINI,
so you may have to get the GEMINI closer to your router. Any
openings in the transformer may help as well, just make sure they
are still water tight. You may also invest in a WiFi signal booster to
strengthen the signal from you WiFi router.
5. Does it create its own WIFI signal?
Yes, out of the box the Gemini will create its own WiFi signal (it will
show up as ECO-XXXX when finding it on your smartphone). You then
will integrate it with your home/office router (see page 2 for details on
setting that up).
6. Why does it shut off before the programmed time?
If you have your GEMINI seemingly turning on or off at odd times,
double check your TIMERS in on your GEMINI. You may have
redundant or overlapping timers you setup by mistake.
7. What is the difference between GM1 & GM2?
The only differences are the physical size, and the location of the
3-pronged grounded outlet.
8. How do I program sunset on and timed event off?
First, you would set up an ASTRONOMIC TIMER. Set it to turn ON
the GEMINI at Sunset, and OFF at Sunrise. THEN, create a timed
event with the PROGRAMMABLE TIMER that turns ON the GEMINI
at 11:00PM and OFF at the desired time, say 1:00am. Since the
ASTRONOMIC timer has already told the GEMINI to turn ON at
Sunset, the PROGRAMMABLE TIMERs first event will be redundant,
and will NOT effect the GEMINI. Then, at 1:00am the GEMINI will turn
OFF as programmed by the PROGRAMMABLE TIMER function. (see
page 3 for more help)
9. How many devices can I put on the app?
You can set up to 12 Gemini units on the ECO Plugs APP.
10. Can I / how do I save my customers’ info so I can access it later
if I have more than x devices on my app?
All custom timers and info will be saved via the customers WiFi
router onto the Gemini unit. So anytime you or anyone else connects
to that routers WiFi and open the ECO Plugs, all those timers on each
of the Gemini units associated with that router will show up.
11. How do I set it up so more than one person in the house can
have access?
See page 2 section: ADD MULTIPLE USERS TO ECO PLUGS
12. Can you use the GEMINI on a router with NO password?
It is okay to use the Wi-Fi without a password. However, it may be
necessary to check the router’s Firewall, and add the ECO Number
(ECO-78017E7F) to its accepted ports. Also, check that the router is
on P2P mode. If it is not, please change to P2P mode.
13. Is a WiFi signal required?
It is highly recommended for a WiFi signal to be present for the
GEMINI to be connected to (see page 2). However, if NO WiFi signal
is present where the GEMINI is being installed, it is possible to
preprogram the GEMINI and bring it on site. It will perform the
preprogrammed timer functions. However, since it is not connected
to WiFi, it is not associated with the zip code and may waver on
the exact time of day. In addition, if any new WiFi signals become
available, the GEMINI will attempt to connect to them and will no
longer perform the preprogrammed timer functions.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.
Contains FCC ID: PAGECO-PLUGS
This equipment has been tested and found to comply with the limits for Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the RCC Rules.
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may
cause undesired operation of the device.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
4
FAQ
FOR MORE INFORMATION
CONTACT
INFORMATION
COPYRIGHT
Business Address
22 Harcourt Road
Rochester, New York 14606
(585) 254 – 8010
(585) 254 – 8033
www.illuminfx.com
info@illuminfx.com
Entire contents © illuminFx Lighting Systems.
All rights reserved.
Reproduction in whole or in part without
permission is strictly prohibited.
Phone
Fax
Made in China