7361863 (rev. C 6/14/17) how to install, operate and maintain your whole home water treatment system do not return system to store manufactured and warranted by ecodyne water systems 1890 woodlane drive woodbury, mn 55125 if you have any questions or concerns when installing, operating or maintainin...
2 table of contents page specifications & performance claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
3 * capacity to reduce clear water iron is substantiated by laboratory test data. State of wisconsin requires additional treatment if water supply contains clear water iron exceeding 5 ppm. ** typical residential chlorine concentration is 0.5 to 1.0 ppm. § from independent laboratory test data. This...
4 safety guides = the water treatment system requires a minimum water flow of 3 gallons (11.4 l) per minute at the inlet. Maximum allowable inlet water pressure is 100 psi (7.0 kg/cm 2 ). If your house water pressure is over the maxi- mum, install a pressure reducing valve in the water supply pipe t...
5 packing list inspect shipment water treatment information iron iron in water can cause stains on clothing and plumb- ing fixtures. It can negatively affect the taste of food, drinking water, and other beverages. Iron in water is measured in parts per million (ppm). The total* ppm of iron, and type...
6 plumbing codes all plumbing must be completed in accordance with national, state and local plumbing codes. Air gap requirements a drain is needed for regeneration water (see figure 3). A floor drain, close to the water treatment system, is preferred. A laundry tub, standpipe, etc. Are other drain ...
7 installation requirements valve drain requirements using the flexible drain hose (included), measure and cut to the length needed. Flexible drain hose is not allowed in all localities (check your plumbing codes). If local codes do not allow use of a flexible drain hose, a rigid valve drain run mus...
8 installation instructions turn off water supply 1. Close the main water supply valve, located near the well pump or water meter. 2. Shut off the electric or fuel supply to the water heater. 3. Open all faucets to drain all water from house pipes. Note: be sure not to drain water from the water hea...
9 installation instructions fig. 13 top cover brine tank overflow elbow brine tank overflow grommet 2 cm hole salt lid salt storage tank float stem brine tubing brinewell cover stand tube brine valve brinewell nozzle & venturi assembly fig. 10 turbine turbine support assembly valve outlet fig. 11 cl...
10 installation instructions install valve drain hose note: see valve drain options on pages 6 & 7. 1. Measure, cut to needed length and connect the 9.5 mm drain line (provided) to the water treatment sys- tem valve drain fitting. Use a hose clamp to hold the hose in place. Important: if codes requi...
11 installation instructions fig. 15 ...Depressurize the plumbing, then push by - pass valve body toward water treatment system if removing clips... 7. After you hear the valve motor stop running (valve in “brine” position), press, but do not hold, the recharge button. The valve will advance to the ...
12 fig. 17 fig. 16 low salt led indicator display select button down button recharge button up button program the system when the power supply is plugged into the electrical outlet, the model code and a software version number (example: j3.9), are briefly shown in the display. Then the words “presen...
13 programming the water treatment system fig. 19 set water hardness number 1. Press the select button once again to display a flashing “25” and the word “hardness”. 2. Press the p up or q down buttons to set your water’s hardness number. Note: if your water supply contains iron, compen- sate for it...
14 customizing features / options recharge now at times of greater than normal water use, such as when you have guests, you could run out of treated water before the next scheduled recharge. If this happens, you may want to initiate an immediate regeneration, as follows: 1. Press and hold the rechar...
15 customizing features / options 3. Use the p up or q down buttons to change between “12 hr” and “24 hr”. 4. When the desired setting appears in the display, press the select button three times to return to the normal run (time of day) screen. Adjustable backwash if your incoming water supply has h...
Features / options 16 power outage memory if electrical power to the water treatment system is lost, “memory'' built into the timer circuitry will keep all settings for several hours. While the power is out, the display is blank and the system will not regenerate. When electrical power is restored, ...
17 routine maintenance floor drain fig. 33 wood block fig. 32 cap o-ring seal screen support screen gasket *flow plug (hvdc) housing ferrule nut cone screen *flow plug *install with lettered side up, concave side down. Cleaning the nozzle & venturi a clean nozzle & venturi (see figure 32) is a neces...
18 troubleshooting guide problem cause correction no soft water 1. No salt in the storage tank. Refill with salt and then use recharge now feature. No soft water & dis- play is blank 1. Power supply unplugged at wall outlet, or power cable disconnected from back of elec - tronic board or power suppl...
19 while an error code appears in the display, all buttons are inoperable except the select button. Select remains operational so the service person can per- form the manual advance diagnostics, see below, to further isolate the problem. Procedure for removing error code from dis- play: 1. Unplug po...
20 troubleshooting need help troubleshooting? Call toll free 1-800-693-1138 or visit www.Ecopure.Com when you call, please be prepared to provide the model and serial number, found on the rating decal, located on the rim below the salt lid hinges. Resetting to factory defaults to reset the electroni...
21 notes.
22 8 7 6 5 water treatment system exploded view 27 26 28 15 16 12 18 19 20 11 22 23 24 25 8 6 3 9 10 7 valve assembly see pages 24 & 25 for parts 5 2 1 21 4 14 13 17.
23 water treatment system parts list key no. Part no. Description – 7112963 distributor o-ring kit (includes key nos. 1-3) 1 á o-ring, 73.0 x 82.6 mm 2 á o-ring, 20.6 x 27.0 mm 3 á o-ring, 69.9 x 76.2 mm 4 7265025 filter screen 5 7077870 top distributor 6 7105047 repl. Bottom distributor – 7331177 t...
24 valve exploded view 51 50 52 53 55 56 59 58 57 60 61 66 67 62 63 64 68 69 70 71 72 73 74 75 65 76 77 79 78 80 81 82 wear strip seal cross-section view 83 84 85 86 87 88 89 90 54 70 91.
25 valve parts list key no. Part no. Description 50 7338111 screw, #6-19 x 3.5 cm (2 req.) 51 7281291 motor 52 7337474 motor mount 53 7284964 cam & gear 54 7030713 switch – 7331185 drain hose adaptor kit (includes key nos. 55-59) 55 á clip, drain 56 á drain hose adaptor 57 á hose clamp 58 á o-ring, ...
26 whole home water treatment system warranty warrantor: ecodyne water systems, 1890 woodlane drive, woodbury, mn 55125 warrantor guarantees, to the original owner, that: one year full warranty: ● for a period of one (1) year from the date of purchase, all parts will be free from defects in material...
