1. DL manuals
  2. ECOFOREST
  3. Heat Pump
  4. ecoGEO C
  5. Installation And User Manual

ECOFOREST ecoGEO C Installation And User Manual

Summary of ecoGEO C

  • Page 1

    Ecogeo c installation and user manual.

  • Page 2: Table Of Contents

    Ecogeo c installation and user manual (version 1.0) page 2 table of contents 1 general information ............................................................................................................................................ 4 2 safety issues .............................................

  • Page 3

    Ecogeo c installation and user manual (version 1.0) page 3 8 technical specifications ..................................................................................................................................... 61 8.1 t echnical data table ......................................................

  • Page 4: 1  General Information

    Ecogeo c installation and user manual (version 1.0) page 4 1 general information thank you for purchasing an ecoforest ecogeo c heat pump. In this manual you will find information on installing, commissioning, maintaining and troubleshooting the equipment. You can also find useful user information, ...

  • Page 5: 2  Safety Issues

    Ecogeo c installation and user manual (version 1.0) page 5 2 safety issues the instructions in this section cover important safety aspects, so be sure to abide by them. 2.1 refrigerant circuit the refrigeration system uses r410a as the working fluid. This refrigerant is not harmful to the environmen...

  • Page 6

    Ecogeo c installation and user manual (version 1.0) page 6 toxicity under normal operating conditions, the heat pump refrigerant is not toxic. However, despite its low toxicity, injury can occur during abnormal operation. • in its gaseous state, the refrigerant is heavier than air, so it tends to ac...

  • Page 7

    Ecogeo c installation and user manual (version 1.0) page 7 2.3 electrical installation any action on the electrical installation should be performed only by authorized personnel according to applicable local regulations and the instructions provided in this manual. Danger! Before performing any oper...

  • Page 8

    Ecogeo c installation and user manual (version 1.0) page 8 3 overview of the heat pump 3.1 identifying the model the ecogeo c heat pump range includes a built-in, 170 litre hot water tank. This heat pump range is available in 6 different models depending on their scope and thermal power, as stated i...

  • Page 9

    Ecogeo c installation and user manual (version 1.0) page 9 3.2 operating principles ecoforest geothermal pumps are designed to be easy to install, and provide heating, cooling and dhw all year round, while ensuring maximum energy efficiency. Figure 3.1. Geothermal heat pump installations using geoth...

  • Page 10

    Ecogeo c installation and user manual (version 1.0) page 10 3. The hot gas from the compressor is led to the condenser where it releases its heat to the water in the heating system. Following this transfer of heat, the refrigerant is cooled and condensed, becoming liquid. 4. The liquid refrigerant f...

  • Page 11

    Ecogeo c installation and user manual (version 1.0) page 11 at this temperature the bacteria cannot survive for over 20 minutes. It is recommended that these heating procedures be done at night, when it is more likely that the hot water tank is at a higher temperature and when no dhw is consumed, th...

  • Page 12

    Ecogeo c installation and user manual (version 1.0) page 12 3.3 dimensions and connections the overall dimensions of the heat pumps ecogeo c range are specified in figure 3.2 . 4 5 6 7 9 8 10 600 700 1800 3 1 2 number description number description 1 upper module 6 brine outlet (g1'' f) 2 lower modu...

  • Page 13

    Ecogeo c installation and user manual (version 1.0) page 13 3.4 main components ecogeo c1 models 1 3 22 2 4 5 6 7 9 8 24 30 29 10 11 14 12 16 15 27 21 25 13 31 32 28 20 19 17 23 18 26 number description number description 1 dhw tank (170 l) 17 dhw circuit check valve 2 electrical cabinet 18 dhw circ...

  • Page 14

    Ecogeo c installation and user manual (version 1.0) page 14 ecogeo c2 models 1 3 25 2 4 6 7 8 10 9 27 33 32 11 12 17 16 13 19 34 30 24 28 29 18 35 31 23 22 20 26 5 15 14 21 number description number description 1 dhw tank (170 l) 19 heating/cooling safety valve (6 bar) 2 electrical cabinet 20 dhw ci...

  • Page 15

    Ecogeo c installation and user manual (version 1.0) page 15 ecogeo c3 models 1 3 28 2 4 6 7 8 14 13 30 36 35 16 17 19 18 21 37 33 27 31 20 38 34 26 25 22 29 15 24 11 5 9 10 12 23 32 number description number description 1 dhw tank (170 l) 20 brine safety valve (6 bar) 2 electrical cabinet 21 heating...

  • Page 16

    Ecogeo c installation and user manual (version 1.0) page 16 3.5 access to the interior installation, commissioning and maintenance of the heat pump requires access to various points inside the heat pump. To do so, it may be necessary to remove one or more of the equipment's covers. Ecogeo c heat pum...

  • Page 17

    Ecogeo c installation and user manual (version 1.0) page 17 access to the lower front part 1. Remove the upper front cover as described above. 2. Remove the fixing screws located on the top of the lid. 3. Pull the cover upwards to disengage the cover from the structure. 4. Remove the cover by pullin...

  • Page 18

    Ecogeo c installation and user manual (version 1.0) page 18 access to the sides 1. To access the lower side of the module, remove the upper and lower front covers. To access the side of the upper module, remove only the top front cover. 2. Remove the fixing screws located on the top of the side cove...

  • Page 19

    Ecogeo c installation and user manual (version 1.0) page 19 access to the rear and the top the covers of the rear and top of the heat pump can also be removed if necessary. 1. Remove the screws holding the cover to the frame. 2. Remove the cover and put it in a place where it can not be damaged. X4 ...

  • Page 20: 4  User Guide

    Ecogeo c installation and user manual (version 1.0) page 20 4 user guide 4.1 description of the front panel the heat pump front panel consists of a monochromatic display and 6 buttons, as shown in figure 4.1. The general functions of each of the buttons is shown below the picture. To access certain ...

  • Page 21

    Ecogeo c installation and user manual (version 1.0) page 21 summer program the heat pump only permits activation of the operating modes free cooling and active cooling, dhw, legionella protection and fault. Heating mode is not allowed. Auto program the heat pump automatically selects between winter/...

  • Page 22

    Ecogeo c installation and user manual (version 1.0) page 22 icon meaning winter program activated summer program activated auto auto program activated heating mode activated free cooling/active cooling mode activated dhw mode activated legionella protection mode activated fault mode activated compre...

  • Page 23

    Ecogeo c installation and user manual (version 1.0) page 23 1.2.5. Ecogeo schedule 4 1.2.6. Ecogeo schedule 5 1.2.7. Date/hour 1.2.8. Clock 1.3. Heating 1.3.1. Heating 1 1.3.2. Heating 2 1.4. Dhw 1.4.1. Dhw 1.4.2. Legionella protection 1.5. Active cooling 1.5.1. Active cooling 1 1.5.2. Active coolin...

  • Page 24

    Ecogeo c installation and user manual (version 1.0) page 24 menu 1.2. Schedule menu 1.2.1 time schedule choosing the type of time programming between none, from the th-tune indoor terminal, or from the heat pump front panel. Programming by th-tune is only displayed and selectable if the option is en...

  • Page 25

    Ecogeo c installation and user manual (version 1.0) page 25 it is turned off. At 23:00 it comes on again, with setpoint set2, shutting down at 24:00, at the end of the day. Figure 4.4. Screen for setting hourly slots, example with the heat pump turned off at 24:00. Another situation that must be tak...

  • Page 26

    Ecogeo c installation and user manual (version 1.0) page 26 figure 4.6. Screen for configuring holiday periods, an example that solves the event of a holiday period with change of year. Menu 1.2.6 ecogeo schedule 5 (scheme 3 or scheme 4 with th-tune) / ecogeo schedule 3 (remaining operating schemes)...

  • Page 27

    Ecogeo c installation and user manual (version 1.0) page 27 menu 1.4. Dhw menu 1.4.1 dhw selecting the setpoint temperature for dhw and the offset to begin production; that is, the degrees below the setpoint which, as a minimum, must be measured in the dhw temperature probe for it to begin dhw produ...

  • Page 28

    Ecogeo c installation and user manual (version 1.0) page 28 menu 1.7. Information compiles all the relevant information when observing the operation of the heat pump. You can access this menu quickly, by pressing the [←] button on the front panel from the start screen. Menu 1.7.1 information 1 for a...

  • Page 29

    Ecogeo c installation and user manual (version 1.0) page 29 4.6 service menu the service menu of the ecoforest ecogeo heat pump is intended for less frequent use than the previous one and includes submenus for changing the language, configuration or secondary information on the heat pump. It can be ...

  • Page 30

    Ecogeo c installation and user manual (version 1.0) page 30 2.4.5.6 heating pressure 2.4.5.7 suction temp. 2.4.5.8 suction pressure 2.4.5.9 discharge pressure 2.4.5.10 dhw temp. 2.4.5.11 temp. Dep. 2/outlet temp. 2 2.4.5.12 outdoor temp. 2.4.6. Alarm log 2.4.7. Default values 2.4.8. Change password ...

  • Page 31

    Ecogeo c installation and user manual (version 1.0) page 31 selection of system and dwelling parameters for establishing and defining the heating curve. Table 6.2 details the recommended values for each of the parameters depending on the system chosen. Menu 2.4.2.1. Design parameters 1 defines the i...

  • Page 32

    Ecogeo c installation and user manual (version 1.0) page 32 figure 4.7. Bms configuration screen for th-tune indoor terminals, with the recommended values for the correct operation of the heat pump. Menu 2.4.4 manual conf. This allows the activation of the relays that control various heat pump devic...

  • Page 33

    Ecogeo c installation and user manual (version 1.0) page 33 menu 2.4.4.4. Inverter contactor for all ecogeo heat pump models. The status (on / off) the inverter contactor can be defined. Menu 2.4.4.5. Elect. Heater cont. For all ecogeo heat pump models and all operating schemes. The status (on / off...

  • Page 34

    Ecogeo c installation and user manual (version 1.0) page 34 menu 2.4.5.3 heating outlet temp. Displays the type and value measured by the heating/cooling outlet temperature probe with an offset for correcting the value. Menu 2.4.5.4 heating inlet temp. Displays the type and value measured by the hea...

  • Page 35

    Ecogeo c installation and user manual (version 1.0) page 35 menu 2.4.7 default value the settings established by the user can be substituted by default values. Menu 2.4.8 change password it allows to change the service password (pw1). 4.7 alarms menu it is accessed by pressing the [alarm]button. For...

  • Page 36: 5  Installation

    Ecogeo c installation and user manual (version 1.0) page 36 5 installation to carry out the installation of the heat pump follow these steps in the order listed. 1. Carefully remove the packaging of the heat pump (wooden box, plastic, etc.). 2. Carefully remove the fasteners that fix the heat pump t...

  • Page 37

    Ecogeo c installation and user manual (version 1.0) page 37 before selecting the place the heat pump will be installed, consider the following recommendations. • choose a dry place where there is no risk of frost. • if possible, install the heat pump with the back towards an outer wall and in a room...

  • Page 38

    Ecogeo c installation and user manual (version 1.0) page 38 5.3 service areas we recommend leaving enough space around the heat pump to facilitate the installation and maintenance work. Recommended minimum distances from walls and other structures are indicated below. • 300 mm from both sided. • 300...

  • Page 39

    Ecogeo c installation and user manual (version 1.0) page 39 5.4 heating/cooling circuit connection ecogeo c heat pumps are designed for use in heating systems with low temperature heat radiators (underfloor heating or fan coil) or medium temperature radiators (convector or low temperature radiators)...

  • Page 40

    Ecogeo c installation and user manual (version 1.0) page 40 • we recommend connecting the heating/cooling indoor circuit to the mains water through a pressure reducing valve. This ensures the correct operating pressure of the heating/cooling system in the event of possible water leaks or removal of ...

  • Page 41

    Ecogeo c installation and user manual (version 1.0) page 41 5.5 dhw circuit connection to connect the dhw circuit piping, take into account the note in figure 5.3 and the following recommendations. • to facilitate future maintenance work on the heat pump, install shut-off valves in the mains water i...

  • Page 42

    Ecogeo c installation and user manual (version 1.0) page 42 2 3 7 4 4 1 ecogeo c1 ecogeo c2 ecogeo c3 5 6 number description number description 1 heat pump 5 check valve 2 mains water input (g1'' f) 6 thermostatic mixing valve 3 dhw outlet (g1'' f) 7 safety valve (8 bar) 4 shut-off valve figure 5.3....

  • Page 43

    Ecogeo c installation and user manual (version 1.0) page 43 5.6 brine circuit connection ecogeo c heat pumps can be used with horizontal, vertical or groundwater brine systems. The geothermal collectors/probes must be properly dimensioned, taking into account the geographical area, the terrain, the ...

  • Page 44

    Ecogeo c installation and user manual (version 1.0) page 44 the refrigerant evaporation temperature can fall below 0 ° c. Thus, in brine systems with groundwater we recommend using an intercooler to prevent freezing problems and evaporator fouling. Inside the heat pump are included the following com...

  • Page 45

    Ecogeo c installation and user manual (version 1.0) page 45 3 5 4 4 2 6 1 ecogeo c1 ecogeo c2 ecogeo c3 number description number description 1 heat pump 4 shut-off valve 2 brine outlet, (g1'' f) 5 particle filter 3 brine inlet, (g1'' f) 6 brine filling fitting figure 5.5. General diagram of brine c...

  • Page 46

    Ecogeo c installation and user manual (version 1.0) page 46 the electrical installation of the heat pump should be performed by a qualified installer in accordance with applicable local regulations and instructions. Figure 5.6 indicates the location of the main components of the electrical cabinet. ...

  • Page 47

    Ecogeo c installation and user manual (version 1.0) page 47 the electrical installation required for the heat pump is only the power cord connection, the external temperature probes and external control valve connections. Power supply all models in the range ecogeo c require single-phase 230 v / 50 ...

  • Page 48

    Ecogeo c installation and user manual (version 1.0) page 48 to install the terminal both the power supply and the rs485 serial cable must be connected. Before installation, bear in mind the following recommendations. 1. Before connecting the power supply terminal carefully read the instructions in t...

  • Page 49

    Ecogeo c installation and user manual (version 1.0) page 49 38 39 t1 t2 tn figure 5.9. Wiring of one or more conventional relay type thermostats. Outdoor temperature probe the outdoor temperature probe is connected by twin-pole cables to the lower terminal strip of the electrical cabinet, as indicat...

  • Page 50

    Ecogeo c installation and user manual (version 1.0) page 50 21 22 figure 5.11. Wiring diagram for the outdoor temperature probe to the electrical cabinet. Buffer tank temperature probe (facilities with intermediate buffer tank) the buffer storage temperature probe is connected by twin-pole cables to...

  • Page 51

    Ecogeo c installation and user manual (version 1.0) page 51 number description number description 1 modulating 3-way valve 4 analogue output signal 0-10 v 2 circulating pump 5 relay output 3 outlet temperature probe 6 ntc analogue input figure 5.13. Wiring diagram for connecting the circulating pump...

  • Page 52: 6  Start Up

    Ecogeo c installation and user manual (version 1.0) page 52 6 start up to carry out the start-up of the heat pump, follow these steps in the order listed. 1. Fill the heating/cooling indoor circuit by following the directions in section 6.1 . 2. Fill the built in circuit coil in the dhw tank as desc...

  • Page 53

    Ecogeo c installation and user manual (version 1.0) page 53 the coil circuit built into the hot water tank is connected to the heating circuit. Therefore, filling this circuit is simultaneous with the heating circuit. To do this, open the automatic air vent located at the entrance of the coil at the...

  • Page 54

    Ecogeo c installation and user manual (version 1.0) page 54 6.3 filling the dhw tank to fill the hot water tank, follow these steps. 1. Open the valve located in the mains water inlet pipe. 2. Open one or more hot water taps in the dwelling to fully purge the air in the tank. To empty the dhw tank, ...

  • Page 55

    Ecogeo c installation and user manual (version 1.0) page 55 3 5 4 4 2 6 1 ecogeo c1 ecogeo c2 ecogeo c3 8 9 7 11 10 number description number description 1 heat pump 7 filling valve a 2 brine outlet 8 filling valve b 3 brine inlet 9 filling valve c 4 shut-off valve 10 external filling pump 5 particl...

  • Page 56

    Ecogeo c installation and user manual (version 1.0) page 56 4. Close filling valve a (7). 5. Open filling valves b and c. 6. Activate the external filling pump to fill the circuit. 7. Activate in manual mode the brine circuit pump (service menu -> installer conf. -> manual conf. -> brine pump -> sta...

  • Page 57

    Ecogeo c installation and user manual (version 1.0) page 57 11. Only if indoor th-tune terminals are installed go to th-tune and enable the th-tune option. Set values of 1 and 2 for the indoor terminal address of the main and secondary zones, respectively. This second zone only exists if you have se...

  • Page 58

    Ecogeo c installation and user manual (version 1.0) page 58 before initial start-up, check the following points to ensure that they have been completed successfully. 1. Inspect heating, brine and dhw circuits. • the heating/cooling indoor system was performed according to figure 5.2, including all c...

  • Page 59

    Ecogeo c installation and user manual (version 1.0) page 59 7 identifying problems and troubleshooting. 7.1 alarms lists there are a number of parameters that the heat pump monitors at all times to check the equipment is working properly. If any of these parameters is not within the standard value r...

  • Page 60

    Ecogeo c installation and user manual (version 1.0) page 60 7.2 comfort problems the following list shows some of the common comfort-related problems that can be found and their possible causes and remedies. Symptom possible cause remedy dhw temperature too low occasional high demand for dhw wait a ...

  • Page 61

    Ecogeo c installation and user manual (version 1.0) page 61 8 technical specifications 8.1 technical data table ecogeo c geothermal pumps technical data unit ecogeo c1 ecogeo c2 ecogeo c3 3-12 5-22 3-12 5-22 3-12 5-22 application heating and dhw - • • • • • • integrated dhw tank 170 l - • • • • • • ...

  • Page 62

    Ecogeo c installation and user manual (version 1.0) page 62 8.2 internal diagrams of the heat pump ecogeo c1 position 1. Brine outlet, (g1'’ f) 2. Brine inlet, (g1'’ f) 3. Heating outlet, (g1'’ f) 4. Heating inlet, (g1'’ f) 5. Dhw outlet, (g1’’ f) 6. Cold water inlet (g1’’ f) 7. Dhw tank 8. Dhw circ...

  • Page 63

    Ecogeo c installation and user manual (version 1.0) page 63 ecogeo c2 position 1. Brine outlet, (g1'’ f) 2. Brine inlet, (g1'’ f) 3. Heating/cooling outlet, (g1'’ f) 4. Heating/cooling inlet, (g1'’ f) 5. Dhw outlet, (g1’’ f) 6. Cold water inlet, (g1’’ f) 7. Dhw tank 8. Dhw circuit coil 9. Electric h...

  • Page 64

    Ecogeo c installation and user manual (version 1.0) page 64 ecogeo c3 position 1. Brine outlet, (g1'’ f) 2. Brine inlet, (g1'’ f) 3. Heating/cooling outlet, (g1'’ f) 4. Heating/cooling inlet, (g1'’ f) 5. Dhw outlet, (g1’’ f) 6. Cold water inlet, (g1’’ f) 7. Dhw tank 8. Dhw circuit coil 9. Electric h...

  • Page 65

    Ecogeo c installation and user manual (version 1.0) page 65 8.3 location of electrical cabinet connections upper terminal block ecogeo c1 and ecogeo c2 models t_ 1 t_ 2 90 80 91 81 92 82 93 83 94 84 95 85 96 97 86 87 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 68 69 70 71 72 73 74 75.

  • Page 66

    Ecogeo c installation and user manual (version 1.0) page 66 upper terminal block ecogeo c3 models t_ 1 t_ 2 90 80 91 81 92 82 93 83 94 84 95 85 96 97 86 87 41 42 43 44 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75.

  • Page 67

    Ecogeo c installation and user manual (version 1.0) page 67 connections on the upper terminal block of the electrical cabinet terminal no. Component t_1 ground power supply 90 neutral 91 phase 93 inverter / compressor 94 96 electric heater (legionella protection) 97 41 high-pressure switch 42 43 low...

  • Page 68

    Ecogeo c installation and user manual (version 1.0) page 68 lower terminal block on ecogeo c1, ecogeo c2 and ecogeo c3 models 89 88 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

  • Page 69

    Ecogeo c installation and user manual (version 1.0) page 69 connections on the lower terminal block of the electrical cabinet terminal no. Component 1 ntc analogue input brine outlet temp. Probe 2 3 ntc analogue input brine inlet temp. Probe 4 5 ntc analogue input heating outlet temp. Probe 6 7 ntc ...

  • Page 70

    Ecogeo c installation and user manual (version 1.0) page 70 8.4 wiring diagrams ecogeo c1 ecogeo c1 power diagram 230 v ~ 95 85 86 87 96 97 ra 92 82 230v ~ 83 84 93 94 extension filter ef_2 ef_1 inverter ef_4 ef_3 m 3 ~ i_1 i_2 i_4 i_3 i_5 compresor 80 91 81 g0 g 88 89 pra prb 44 43 42 41 alarm bcl ...

  • Page 71

    Ecogeo c installation and user manual (version 1.0) page 71 ecogeo c1 micro-controller connection diagram j1 j4 j5 j3 j2 j16 j18 g0 +vdc gnd b3 b2 b1 +5 vref gnd +vdc g id7 id6 id5 id4 id3 id2 id1 b11 b10 b9 idc1 b12 gnd id8 id9 id10 idc2 j8 j9 j10 j12 j13 j14 j15 gnd rx+/tx+ rx-/tx- no3 no2 no1 c1 ...

  • Page 72

    Ecogeo c installation and user manual (version 1.0) page 72 ecogeo c1 micro-controller connections nomenclature description g micro-controller power supply (phase) g0 micro-controller power supply (neutral) pra high-pressure switch prb low-pressure switch digital inputs ebc heat pump on signal analo...

  • Page 73: Upc

    Ecogeo c installation and user manual (version 1.0) page 73 installation diagrams ecogeo c1 upc 1 2 4 3 ticap tac trcl trcap ticl pccap tdep 2 timp 2 tdep 1 pdc pac text pccl rbcl rbcap etr bit 2 rvmt 2 bcap bcl alarm black white 230 v ~ vacs ef ra prb pra white black 5 6 white black 7 8 white black...

  • Page 74

    Ecogeo c installation and user manual (version 1.0) page 74 installation connections ecogeo c1 nomenclature description l heat pump power supply (phase) n heat pump power supply (neutral) t heat pump power supply (ground) pra high-pressure switch prb low-pressure switch digital inputs ebc heat pump ...

  • Page 75

    Ecogeo c installation and user manual (version 1.0) page 75 8.5 wiring diagrams ecogeo c2 ecogeo c2 power diagram 230 v ~ 95 85 86 87 96 97 ra 92 82 230v ~ 83 84 93 94 extension filter ef_2 ef_1 inverter ef_4 ef_3 m 3 ~ i_1 i_2 i_4 i_3 i_5 compresor 80 91 81 upc g0 g 88 89 pra prb 44 43 42 41 alarm ...

  • Page 76

    Ecogeo c installation and user manual (version 1.0) page 76 ecogeo c2 micro-controller connection diagram j1 j4 j5 j3 j2 j16 j18 g0 +vdc gnd b3 b2 b1 +5 vref gnd +vdc g id7 id6 id5 id4 id3 id2 id1 b11 b10 b9 idc1 b12 gnd id8 id9 id10 idc2 j8 j9 j10 j12 j13 j14 j15 gnd rx+/tx+ rx-/tx- no3 no2 no1 c1 ...

  • Page 77

    Ecogeo c installation and user manual (version 1.0) page 77 ecogeo c2 micro-controller connections nomenclature description g micro-controller power supply (phase) g0 micro-controller power supply (neutral) pra high-pressure switch prb low-pressure switch digital inputs ebc heat pump on signal analo...

  • Page 78: Upc

    Ecogeo c installation and user manual (version 1.0) page 78 installation diagrams ecogeo c2 upc 1 2 4 3 ticap tac trcl trcap ticl pccap tdep 2 timp 2 tdep 1 pdc pac text pccl rbcl rbcap etr bit 2 rvmt 2 bcap bcl alarm black white 230 v ~ vacs ef ra prb pra white black 5 6 white black 7 8 white black...

  • Page 79

    Ecogeo c installation and user manual (version 1.0) page 79 installation connections ecogeo c2 nomenclature description l heat pump power supply (phase) n heat pump power supply (neutral) t heat pump power supply (ground) pra high-pressure switch prb low-pressure switch digital inputs ebc heat pump ...

  • Page 80

    Ecogeo c installation and user manual (version 1.0) page 80 8.6 wiring diagrams ecogeo c3 power diagrams ecogeo c3 230 v ~ 95 85 86 87 96 97 ra 92 82 230v ~ 83 84 93 94 extension filter ef_2 ef_1 inverter ef_4 ef_3 m 3 ~ i_1 i_2 i_4 i_3 i_5 compresor 80 91 81 micro -controlador g0 g 88 89 no11 pra p...

  • Page 81

    Ecogeo c installation and user manual (version 1.0) page 81 micro-controller connection diagram ecogeo c3 j1 j4 j5 j3 j2 j16 j18 g0 +vdc gnd b3 b2 b1 +5 vref gnd +vdc g id7 id6 id5 id4 id3 id2 id1 b11 b10 b9 idc1 b12 gnd id8 id9 id10 idc2 j8 j9 j10 j12 j13 j14 j15 gnd rx+/tx+ rx-/tx- no3 no2 no1 c1 ...

  • Page 82

    Ecogeo c installation and user manual (version 1.0) page 82 micro-controller connections ecogeo c3 nomenclature description g micro-controller power supply (phase) g0 micro-controller power supply (neutral) pra high-pressure switch prb low-pressure switch digital inputs ebc heat pump on signal analo...

  • Page 83: Upc

    Ecogeo c installation and user manual (version 1.0) page 83 installation diagrams ecogeo c3 upc 1 2 4 3 ticap tac trcl trcap ticl pccap tdep 2 timp 2 tdep 1 pdc pac text pccl rbcl rbcap etr bit 2 rvmt 2 bcap bcl alarm black white 230 v ~ vic ef ra prb pra white black 5 6 white black 7 8 white black ...

  • Page 84

    Ecogeo c installation and user manual (version 1.0) page 84 micro-controller connections ecogeo c3 nomenclature description l heat pump power supply (phase) n heat pump power supply (neutral) t heat pump power supply (ground) pra high-pressure switch prb low-pressure switch digital inputs ebc heat p...

  • Page 85

    Ecogeo c installation and user manual (version 1.0) page 85 8.7 heating output of the heat pump in relation to the compressor speed ecogeo c 3-12 kw models heating inlet/outlet temperature of 30/35 ° c 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 70...

  • Page 86

    Ecogeo c installation and user manual (version 1.0) page 86 ecogeo c 3-12 kw models heating inlet/outlet temperature of 40/45 °c 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 h ea tin g o ut pu t ( kw ) compressor speed (rpm) brine inlet/outlet ...

  • Page 87

    Ecogeo c installation and user manual (version 1.0) page 87 ecogeo c 5-22 kw models heating inlet/outlet temperature of 30/35 ° c 4 6 8 10 12 14 16 18 20 22 24 26 28 30 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 h ea tin g o up ut (k w ) compressor speed (rpm) brine inlet/outlet tem...

  • Page 88

    Ecogeo c installation and user manual (version 1.0) page 88 ecogeo c 5-22 kw models heating inlet/outlet temperature of 40/45 °c 4 6 8 10 12 14 16 18 20 22 24 26 28 30 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 h ea tin g o up ut (k w ) compressor speed (rpm) brine inlet/outlet temp...

  • Page 89

    Ecogeo c installation and user manual (version 1.0) page 89 8.8 power consumption of the heat pump in relation to the compressor speed ecogeo c 3-12 kw models heating inlet/outlet temperature of 30/35 °c 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 700...

  • Page 90

    Ecogeo c installation and user manual (version 1.0) page 90 ecogeo c 3-12 kw models heating inlet/outlet temperature of 40/45 °c 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 in te ns id ad (a ) compressor speed (rpm) brine inlet/outlet tem...

  • Page 91

    Ecogeo c installation and user manual (version 1.0) page 91 ecogeo c 5-22 kw models heating inlet/outlet temperature of 30/35 °c 6 8 10 12 14 16 18 20 22 24 26 28 30 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 cu rre nt (a ) compressor speed (rpm) brine inlet/outlet temperature 0/-3 ...

  • Page 92

    Ecogeo c installation and user manual (version 1.0) page 92 ecogeo c 5-22 kw models heating inlet/outlet temperature of 40/45 °c 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 cu rre nt (a ) compressor speed (rpm) brine inlet/outlet temperatur...

  • Page 93

    Ecogeo c installation and user manual (version 1.0) page 93 9 examples of typical applications ecogeo heat pumps are designed to provide comprehensive heating/cooling and produce dhw (domestic hot water) all year round, using a simple installation and ensuring the maximum energy efficiency possible....

  • Page 94

    Ecogeo c installation and user manual (version 1.0) page 94 9.1 dhw and single area heating with ecogeo c1 4 5 6 3 10 8 8 9 14 9 8 8 2 position 1 . Heat pump 2 . Brine outlet 3 . Brine inlet 4 . Cold wate r inle t 5 . Dhw outlet 6 . Heating outle t 7 . Heating inle t 8 . Shut -off valve 9 . Particle...

  • Page 95

    Ecogeo c installation and user manual (version 1.0) page 95 application • dhw and heating in houses, small apartment blocks, offices or shops with underfloor heating systems, fan coil units, thermo-convector or low-temperature radiators. Operation the heat pump pumps hot water directly to the heatin...

  • Page 96

    Ecogeo c installation and user manual (version 1.0) page 96 9.2 production of hot water for the buffer tank with ecogeo c1 5 6 4 14 11 11 12 12 11 11 3 posi tion 1 . Heat pump 2 . Buffe r tank 3 . Brine outlet 4 . Brine inlet 5 . Cold wate r inle t 6 . Dhw outlet 7 . Buffe r tank outle t 8 . Buffe r...

  • Page 97

    Ecogeo c installation and user manual (version 1.0) page 97 application • dhw and heating in houses, small apartment blocks, offices or shops with heating systems pumping from an intermediate buffer tank. Operation in heating mode, the heat pump drives hot water to the buffer tank. The power supplie...

  • Page 98

    Ecogeo c installation and user manual (version 1.0) page 98 9.3 dhw and heating and free cooling with single area ecogeo c2 4 5 7 3 10 8 8 9 14 9 8 8 2 posi tion 1 . Heat pump 2 . Brine outlet 3 . Brine inlet 4 . Cold wate r inle t 5 . Dhw outlet 6 . Heating /cooling outlet 7 . Heating /cooling inle...

  • Page 99

    Ecogeo c installation and user manual (version 1.0) page 99 application • dhw, heating and free cooling in houses, small apartment blocks, offices or shops with underfloor heating/cooling systems, fan coil units, or thermo-convectors. Operation in heating mode, the heat pump pumps hot water directly...

  • Page 100

    Ecogeo c installation and user manual (version 1.0) page 100 9.4 production of dhw, heating and active cooling by reversing cycle with ecogeo c3 4 5 7 3 10 8 8 9 14 9 8 8 2 position 1 . Heat pump 2 . Brine outlet 3 . Brine inlet 4 . Cold wate r inlet 5 . Dhw outlet 6 . Heating /cooling outlet 7 . He...

  • Page 101

    Ecogeo c installation and user manual (version 1.0) page 101 application • dhw, heating and active cooling in houses, small apartment blocks, offices or shops with underfloor heating/cooling systems, fan coil units, for producing heating and cooling. If underfloor system is used, special care must b...

  • Page 102

    Ecogeo c installation and user manual (version 1.0) page 102 9.5 production of dhw and heating/cooling by reversing cycle with ecogeo c3 with separate heating/cooling emission systems 4 5 6 2 12 11 17 11 10 10 3 7 9 8 10 10 posi tion 1 . Heat pump 2 . Brine outlet 3 . Brine inlet 4 . Cold wate r inl...

  • Page 103

    Ecogeo c installation and user manual (version 1.0) page 103 application • dhw heating and active cooling in houses and small apartment blocks, offices or business premises with independent heating and cooling systems. For example, facilities that combine underfloor heating and fan coil units for co...

  • Page 104: 10 Guarantee

    Ecogeo c installation and user manual (version 1.0) page 104 10 guarantee biomasa ecoforestal villacañas (hereinafter ecoforest) guarantees this product for two (2) years from the date of purchase against defects in workmanship and materials. Additionally, the warranty of the compressor and the inve...

  • Page 105

    Ecogeo c installation and user manual (version 1.0) page 105 anomalies on the delivery note and include a copy for the carrier. You have 24 (twenty four) hours to file your claim in writing to the dealer and/or carrier. • we only accept product returns after ecoforest has provided previously written...

  • Page 106

    Ecogeo c installation and user manual (version 1.0) page 106 information to be included in the suggestion or complaint: name and address of the supplier. Name, address and telephone number of the installer. Name, address and telephone number of the purchaser. Invoice and/or purchase note. Date of in...