- DL manuals
- ECOFOREST
- Heat Pump
- ecogeo hp
- Installation And Operating Manual
ECOFOREST ecogeo hp Installation And Operating Manual
Summary of ecogeo hp
Page 1
Ecogeo hp ecogeo hp 12-40 kw ecogeo hp 15-70 kw ecogeo hp 25-100 kw installation and operating manual.
Page 2: Contents
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 3 ecoforest geotermia contents 1. General information .......................................................................................................................... 5 2. Safety considerations ............................
Page 3
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 4 ecoforest geotermia 9.7. C onfiguration of service response priorities .............................................................................. 52 9.8. C onfiguration of the remote control ...................................
Page 4
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 5 ecoforest geotermia 1. General information thank you for purchasing an ecogeo hp heat pump. This manual contains information about the installation, commissioning, maintenance and troubleshooting of the equipment. There is also...
Page 5
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 6 ecoforest geotermia 2. Safety considerations the detailed instructions in this section cover important aspects for your safety; as such they must be strictly complied with. 2.1. Refrigerant circuit the refrigerant circuit uses ...
Page 6
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 7 ecoforest geotermia the refrigerant in a gaseous state is heavier than air, as such it tends to accumulate at low levels. If the equipment is installed in a location where the accumulation of refrigerant vapour at ground level ...
Page 7
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 8 ecoforest geotermia 2.3. Electrical system any intervention on the electrical system must only be performed by an authorised electrician in accordance with applicable local regulations and the instructions provided in this manu...
Page 8
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 9 ecoforest geotermia 3. General description of the heat pump 3.1. Identification of the model the range of ecogeo hp heat pumps is available in 3 different models depending on the thermal power they provide, as stated in table 3...
Page 9
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 10 ecoforest geotermia 3.2. Operating principles ecogeo hp heat pumps are designed to provide heating and dhw all year round, with easy installation and always ensuring maximum energy efficiency. Installations with geothermal hea...
Page 10
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 11 ecoforest geotermia described below are modes of operation made possible by the different technologies incorporated in ecogeo hp geothermal heat pumps. Heating mode during the normal operating cycle, the heat pumps extract ene...
Page 11
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 12 ecoforest geotermia pool mode pool production is performed by sending hot water to a heat exchanger through which water is supplied to the pool. Fault mode in the event of any failure of the heat pump which stops the compresso...
Page 12
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 13 ecoforest geotermia 3.3. Dimensions and connections in figure 3.2 the overall dimensions are indicated and in table 3.3 the dimensions of the exchanger connections are specified for the heat pumps in the ecogeo hp range. No. D...
Page 13
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 14 ecoforest geotermia 3.4. Main components in figure 3.3 the positions are shown of the main components of the ecogeo hp heat pumps. No. Description no. Description 1 electrical panel 11 compressor suction temp. Probe 2 condense...
Page 14
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 15 ecoforest geotermia 3.5. Accessing the interior for installation, commissioning and maintenance of the heat pump various internal areas need to be accessed. This may require the removal of one or more of the housing covers of ...
Page 15
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 16 ecoforest geotermia figure 3.5. Removing the front cover. To access the sides of an ecogeo hp heat pump follow these steps. 1. Remove the upper cover and front cover as indicated above. 2. Remove the retaining screws located a...
Page 16
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 17 ecoforest geotermia at the rear of the heat pump there are removable covers for easy connection of the pipes to the heat exchangers. To access the heat exchangers of an ecogeo hp heat pump follow these steps. 1. Remove the scr...
Page 17
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 18 ecoforest geotermia 4. User guide 4.1. Description of the control panel the control panel of the heat pump consists of a screen with 6 buttons, as shown in figure 4.1. 2 2 3 6 4 5 1 no. Description no. Description 1 screen 4 a...
Page 18
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 19 ecoforest geotermia alarm menu access button [alarm] from any program location it is possible to quickly access menu 1.9. Alarms (see table 4.2). Back button [esc] from any program location it is possible to go back to the pre...
Page 19
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 20 ecoforest geotermia icon meaning winter program activated summer program activated auto automatic program selection enabled program selection by remote control activated heating mode activated free cooling mode activated dhw m...
Page 20
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 21 ecoforest geotermia 4.4. User menu in table 4.2 the sub-menu structure of menu 1. User is shown. 1. User menu sub-menu level 1 sub-menu level 2 screen 1.1. On/off on/off 1.2. Schedule 1.2.1. Date/time date/time daily saving ti...
Page 21
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 22 ecoforest geotermia menu 1.2. Schedule menu 1.2.1. Date/time date/time. Here it is possible to set the date and time of the heat pump control program. Daily saving time. Here it is possible to enable/disable the automatic time...
Page 22
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 23 ecoforest geotermia menu 1.5. Dhw dhw storage tank. Allows the dhw production status to be selected between enabled / disabled / remote. The remote option is only available if the installer has been previously enabled in menu ...
Page 23
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 24 ecoforest geotermia expansion valve. Displays the various operating parameters of the expansion valve, such as the degree of overheating, the opening percentage, the suction temperature and the evaporation temperature and pres...
Page 24
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 25 ecoforest geotermia 2.2.4.5. Priorities priorities configuration 2.2.4.6. Special programs floor drying installation bleeding 2.2.5. Remote control remote configuration 2.2.6. Protections heating limitation cooling limitation ...
Page 25
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 26 ecoforest geotermia the functions included in each menu are described below. Menu 2.1. Language allows the language of the heat pump management program to be selected. Menu 2.2. Configuration menu 2.2.1. Heat pump model model ...
Page 26
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 27 ecoforest geotermia menu 2.2.4.2. Cooling cooling configuration. Allows the cooling service to be enabled/disabled. Allows the type of connection to be selected between the heat pump and the heating system from among direct co...
Page 27
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 28 ecoforest geotermia menu 2.2.6. Protections power limitation. Allows the maximum thermal power supplied by the heat pump to be adjusted independently for each of the heating, cooling, dhw and pool modes, which is set by limiti...
Page 28
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 29 ecoforest geotermia compressor suction pressure. Displays the type of pressure probe installed in the compressor suction device (refrigerant circuit) and its current reading. It is also possible for a correction to be made to ...
Page 29
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 30 ecoforest geotermia free cooling. Allows the relay to be manually enabled/disabled which controls free cooling (r11). Legionella. Allows the relay to be manually enabled/disabled which controls the legionella protection heater...
Page 30
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 31 ecoforest geotermia 5. Transport and positioning to unpack the heat pump and position it in its final place of installation follow these steps in the order listed. 1. Carefully remove the packaging of the heat pump (wooden box...
Page 31
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 32 ecoforest geotermia check that it is possible to properly install the piping for the brine and production circuits. To avoid condensation in the brine circuit piping, try to reduce the amount of this piping present inside the ...
Page 32
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 33 ecoforest geotermia 6. Hydraulic installation 6.1. Connecting the brine circuit ecogeo hp heat pumps can be used with horizontal, vertical or groundwater collection systems as shown in figure 6.1. The collectors must be sized ...
Page 33
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 34 ecoforest geotermia the refrigerant evaporating temperature can fall below 0 °c. Therefore, with groundwater collection systems it is recommended to use an intermediate exchanger to prevent problems of freezing and fouling of ...
Page 34
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 35 ecoforest geotermia 6.2. Connecting the production circuit ecogeo hp heat pumps are designed for use with low temperature heat emitters (underfloor heating or fancoils) or medium heat emitters (low temperature convector heater...
Page 35
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 36 ecoforest geotermia no. Description no. Description 1 heat pump 9 pool bypass valve 2 production circuit outlet 10 flexible hose 3 production circuit inlet 11 flow switch 4 heating circulation pump 12 particulate filter 5 dhw ...
Page 36
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 37 ecoforest geotermia 7. Electrical installation the electrical installation of the heat pump must be performed by an authorised installer following the applicable local regulations and these instructions. In figure 7.1. The loc...
Page 37
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 38 ecoforest geotermia the internal components of the heat pump are factory connected to the electrical panel via the quick overhead connector terminal blocks. Depending on the installation that the heat pump is going to be conne...
Page 38
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 39 ecoforest geotermia 7.2. Connecting flow switches the flow switches that are included with the heat pump must be connected to the lower terminal blocks of the electrical panel using the quick connectors. To carry out the insta...
Page 39
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 40 ecoforest geotermia 7.3. Connecting external temperature probes the external temperature probes must be connected to the lower terminal block of the electrical panel using the quick connectors. Each of the temperature probes h...
Page 40
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 41 ecoforest geotermia 7.4. Connecting the external control signals the control signals from the external equipment must be connected to the lower terminal block of the electrical panel using the quick connectors. Each of the ext...
Page 41
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 42 ecoforest geotermia 7.5. Connections for the operation of external equipment ecogeo hp heat pumps provide various relay control outputs for operating external equipment, such as circulator pumps or open/closed valves. Each rel...
Page 42
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 43 ecoforest geotermia relay no. Component r1 brine pump activation r2 auxiliary / buffer pump activation r3 dhw production activation r4 dhw recirculation activation r5 pool production activation r6 heating activation of direct ...
Page 43
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 44 ecoforest geotermia figure 7.8. Example of installation of valves with 4 wire power supply. 7.6. Connecting regulation signals for external equipment the regulation signals for the external equipment must be connected to the l...
Page 44
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 45 ecoforest geotermia figure 7.9. Connection diagram of the regulation signals for external equipment to the lower terminal block connector no. + / - component 53 / 54 brine pump adjustment 55 / 56 auxiliary / buffer pump regula...
Page 45
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 46 ecoforest geotermia 8. Filling the circuits before performing the configuration and commissioning of the equipment it is necessary to properly fill, bleed and pressurize all the circuits of the heat pump. To do this, follow th...
Page 46
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 47 ecoforest geotermia no. Description no. Description 1 heat pump 8 safety valve 2 brine circuit outlet 9 brine circulation pump 3 brine circuit inlet 10 brine circuit filling unit 4 flexible hose 11 cutoff valve 5 flow switch 1...
Page 47
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 48 ecoforest geotermia when filling the production circuit only use water. Before starting the heat pump make sure the air in the circuits is completely purged, there is adequate pressure and that there are no leaks. To facilitat...
Page 48
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 49 ecoforest geotermia 9. Configuration and commissioning before starting the heat pump it is necessary to configure it to work with the production and brine systems used and define the main operating parameters. To configure the...
Page 49
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 50 ecoforest geotermia buffer 1t for installations with the heat pump connected to an intermediate buffer separator tank between the heat pump and the heating and/or cooling system and in which the control is performed by a singl...
Page 50
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 51 ecoforest geotermia no. Description no. Description a inside parameters (pdi) b2 outlet temperature for the pde a1 inside parameter temperature c heating cutoff point (pcc) a2 outlet temperature for the pdi c1 heating cutoff t...
Page 51
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 52 ecoforest geotermia 9.5. Configuration of the dhw service to configure the dhw production service access the installer menu (press [prg]+[esc] and enter the installer password pw1) -> configuration -> services -> dhw. 1. On th...
Page 52
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 53 ecoforest geotermia 5. On the cooling alarm screen set the minimum outlet temperature during operation of the heat pump in cooling mode below which the alarm is activated and the heat pump turns off. 9.10. Final inspection and...
Page 53
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 54 ecoforest geotermia commissioning and inspection of abnormal noises 1. Check that the temperature readings from different sensors are correct. 2. Start the heat pump and check that it functions properly in the different operat...
Page 54
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 55 ecoforest geotermia 10. Identifying and solving problems 10.1. List of alarms there are a number of parameters which the heat pump will monitor at all times to verify the correct operation of the equipment. If any of these par...
Page 55
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 56 ecoforest geotermia 10.2. Comfort problems the following table includes some of the common comfort problems with that can occur and their possible causes and remedies. Symptom possible cause remedy dhw temperature too low high...
Page 56
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 57 ecoforest geotermia 11. Technical specifications 11.1. Technical data table in table 11.1 are the main technical characteristics of ecogeo hp models. Ecogeo hp geothermal pumps technical data unit ecogeo hp 12-40 kw ecogeo hp ...
Page 57
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 58 ecoforest geotermia 11.2. Internal scheme in figure 11.1 the internal scheme is shown of a heat pump from the ecogeo hp range and in table 11.2 the main components are indicated. Figure 11.1. Internal scheme of the ecogeo hp h...
Page 58
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 59 ecoforest geotermia 11.3. Connections table for the electrical panel in figure 11.2 the upper block of the electrical panel relays is shown and in table 11.3 the list of connections is shown. Figure 11.2. Upper block of the el...
Page 59
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 60 ecoforest geotermia in figure 11.3 the lower terminal block is shown of the electrical panel quick connectors and in table 11.4 the list of connections is shown. Figure 11.3. Lower block of quick connectors of the electrical p...
Page 60
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 61 ecoforest geotermia 31 signal analogue input ntc compressor discharge temperature probe 32 earth 33 signal analogue input ntc dhw inter-accumulator temperature probe 34 earth 35 signal analogue input ntc dhw inlet temperature ...
Page 61
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 62 ecoforest geotermia 79 signal digital input 24 vdc / 24 vac cooling production demand of mixture group 2 80 earth 81 signal digital input 24 vdc / 24 vac heating production demand of mixture group 3 82 earth 83 signal digital ...
Page 62
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 63 ecoforest geotermia 11.4. Electrical diagrams in figure 11.4 the power circuit diagram is shown for ecogeo hp heat pumps. Figure 11.4. Power circuit diagram for heat pumps in the ecogeo hp range..
Page 63
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 64 ecoforest geotermia in figure 11.5 the connection scheme is shown for the pco5+ controller module of the heat pump. Figure 11.5. Connection scheme for the pco5+ controller module..
Page 64
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 65 ecoforest geotermia in figure 11.6 the connection scheme is shown for the pco e expansion modules of the heat pump. Figure 11.6. Connection scheme for the pco e expansion modules. G0 g 2 4 v ~ y1 vg0 rgm4 61 62 vg t- t+ gnd di...
Page 65
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 66 ecoforest geotermia connection terminal no. Description nomenclature external power supply connector j1 – pco5+ g controller module external power supply l (24 vac) g0 n (0 vac) active probes power supply connector j24 – pco5+...
Page 66
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 67 ecoforest geotermia id11 heating production demand of group 4 ecgm4 id12 cooling production demand of group 4 ergm4 idc9 common digital inputs -- relay outputs – group 1 connector j12 – pco5+ c1 common relays for connector j12...
Page 67
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 68 ecoforest geotermia connection terminal no. Description nomenclature external power supply connector j1 – pco e -1 g expansion module external power supply l (24 vac) g0 n (0 vac) analogue outputs (0-10 vdc) connector j2 – pco...
Page 68
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 69 ecoforest geotermia connection terminal no. Description nomenclature external power supply connector j1 – pco e -2 g expansion module external power supply l (24 vac) g0 n (0 vac) analogue outputs (0-10 vdc) connector j2 – pco...
Page 69
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 70 ecoforest geotermia 11.5. Thermal power limitation the diagram in figure 11.7 shows the thermal power provided by ecogeo hp 12-40 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brin...
Page 70
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 71 ecoforest geotermia the diagram in figure 11.8 shows the thermal power provided by ecogeo hp 12-40 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/7...
Page 71
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 72 ecoforest geotermia the diagram in figure 11.9 shows the thermal power provided by ecogeo hp 15-70 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/7...
Page 72
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 73 ecoforest geotermia the diagram in figure 11.10 shows the thermal power provided by ecogeo hp 15-70 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/...
Page 73
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 74 ecoforest geotermia the diagram in figure 11.9 shows the thermal power provided by ecogeo hp 25-100 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/...
Page 74
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 75 ecoforest geotermia the diagram in figure 11.10 shows the thermal power provided by ecogeo hp 25-100 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10...
Page 75
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 76 ecoforest geotermia 11.6. Electrical consumption the diagram in figure 11.13 shows the electrical consumption of ecogeo hp 12-40 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine...
Page 76
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 77 ecoforest geotermia the diagram in figure 11.14 shows the electrical consumption of ecogeo hp 12-40 kw heat pumps according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/7...
Page 77
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 78 ecoforest geotermia the diagram in figure 11.13 shows the electrical consumption of ecogeo hp 15-70 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/...
Page 78
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 79 ecoforest geotermia the diagram in figure 11.14 shows the electrical consumption of ecogeo hp 15-70 kw heat pumps according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/7...
Page 79
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 80 ecoforest geotermia the diagram in figure 11.13 shows the electrical consumption of ecogeo hp 25-100 kw heat pumps, according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10...
Page 80
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 81 ecoforest geotermia the diagram in figure 11.14 shows the electrical consumption of ecogeo hp 25-100 kw heat pumps according to the rpm of the compressor, for inlet/outlet temperatures in the brine circuit of 0/-3, 5/2 and 10/...
Page 81
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 82 ecoforest geotermia 11.7. Operation map the heat pump operation map indicates the conditions under which the heat pump can operate according to the outlet temperature of the brine and production circuits. The diagram in figure...
Page 82
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 83 ecoforest geotermia 12. Special installation details regarding ecogeo hp heat pumps ecogeo hp heat pumps are designed to provide comprehensive hvac (heating and cooling) with up to five different outlet temperatures, producing...
Page 83
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 84 ecoforest geotermia cold emission systems when using underfloor heating for the production of refrigeration, special care must be taken in the design and control of the installation, since it may cause condensation problems on...
Page 84
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 85 ecoforest geotermia 13. Recommended applications examples of recommended installation for ecogeo hp heat pumps are included in this section. Note that the examples of installations that are included below are only indicative s...
Page 85
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 86 ecoforest geotermia 13.2. Installation example 1 figure 13.1. Installation diagram 1.
Page 86
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 87 ecoforest geotermia 13.3. Installation example 2 figure 13.2. Installation diagram 2.
Page 87
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 88 ecoforest geotermia 13.4. Installation example 3 figure 13.3. Installation diagram 3.
Page 88
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 89 ecoforest geotermia 13.5. Installation example 4 figure 13.4. Installation diagram 4.
Page 89
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 90 ecoforest geotermia 14. Warranty ecoforest geotérmia (hereinafter ecoforest) guarantees this product for two (2) years from the date of purchase against defects in manufacture and materials. Additionally, the warranty of the c...
Page 90
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 91 ecoforest geotermia the warranty does not cover damage caused by: adverse weather conditions, chemicals and/or misuse of the product, lack of maintenance, modifications to or tampering of the equipment and other causes that do...
Page 91
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 92 ecoforest geotermia any suggestions and/or complaints must be submitted in writing to: ecoforest geotermia, s.L. Poligono industrial a pasaxe c/15 - nº22 - parcela 139 36316 - vincios / gondomar - pontevedra (spain) tel.: +34 ...
Page 92
Installation and operating manual. Version 1.00 (08/05/2014) ecogeo hp 93 ecoforest geotermia ecoforest geotermia, s.L. Poligono industrial a pasaxe c/15 - nº22 - parcela 139 36316 - vincios / gondomar - pontevedra (spain) tel.: +34 986 262 184 / +34 986 417 700 fax: +34 986 262 186 e-mail: info@eco...