Summary of 7 Series
Page 1
7 series user guide robot vacuum cleaner.
Page 3
Thanks for purchasing products hope you can enjoy it thanks again for your choice! Patented . ! Robot vacuum cleaner.
Page 5
1. Safety instruction........................... 10.Remote control........ ................................ User guide........................ . Power supply for the product........ ...... Use of remote control the spectrum of product use...... ......... 11.Virtual wall.. ...... .......................
Page 6
1. Safety instruction t he user guide please conform to the basic safety precautions as follows: ● read the content in this user guide carefully and install the robot according to the detailed instructions. ● safekeeping this guide. If you transfer this machine to another person, please make sure at...
Page 7
T he spectr um of the product use ● this robot is applicable to domestic sweeping, including wooden floor, rubber floor, ceramic tile, linoleum and medium or short-haired carpet however, it is inapplicable to long-haired carpet. ● it can not be used for the floor as below: ---- have water on the sur...
Page 8
Notes before cleaning ● take extra care of the robot when the first it works. Please remove the obstacles when it is beyond the robot. Try to avoid the situation that the robot stops working. ● make precautions to solve the problem which may make the cleaning in trouble, such as: keep the easily kno...
Page 9
● take good care of the product and keep it beyond child and people who can not judge danger nearby. Extra attention should be paid when it starts working. ● you should get the person inside the room know that the machine is working, in order to avoid man-made damage like tripping. ● do not take rob...
Page 10
Auto edge spot return intensive 2. C o n t e n t ( f o r d 7 3 ) main unit charging block virtual wall battery for virtual wall user guide border tape magnetic adding tool roll brush clean-up gadget remote control battery for remote control 10 7 series user guide robot vacuum cleaner.
Page 11
12v e n j o y s m a r t e r l i f e ! Dc12v ac220-240v dc14.5v 50hz 30w 1.0a dc3v dc3v ≤5meters 30w 0.25m/s 0.7l ≤60db about 3 hours about 60 minutes 2 120-150m 330 × 330 × 100mm 3.4kg t he host t he charging block remote control vir tual wall working voltage in-put voltage rated out-put voltage rat...
Page 12
2. Content(for d76) main unit technique parameter( f o r d 7 6 ) charge station rated power speed dust capacity noise charging time working time per charge cieaning area per charge function parameter voltage input voltage input voltage rated frequency rated frequency vir tual wall input voltage inpu...
Page 13
3. Parts description(for d73) 13 control button wind gate rotating side brush all-round wheel suspended driving wheel rubber scraper on/off switch dust sensor dust box dust box handle ash exit antibacterial sponge filter lock of dust box charging and alarm open button of upper cover docking electrod...
Page 14
Handheld vacuum cleaner main unit is the same as d73 charge station ( front view) dust container power slot infrared signal generator charging station power cord dust inlet hole air outlet grid charging pin charging station ( top view) handheld vacuum cleaner release button dust inlet hole charging ...
Page 15
1. Power 7. Demo mode 13. Keep timing cleaning 19. Battery display 2. Model selection 8. Border cleaning mode 14. One-time timing cleaning 20. Tip for lacking dust box 3. On/pause 15. Time display 21. Tip for trapped 9. Intensive cleaning mode 4. Pause status 16. Appointment time setting 22. Tip for...
Page 16
Tangle the power cord on the pothook and do not scatter it besides the block or hold it under the base, in case that robot would get impeded when it turns back. 1.5 m 0. 5 m 0. 5 m there should not be any object at least 1.5 meter in front of the charging block. Besides, anything with strong reflect...
Page 17
● press the key on host and get power supply. There would be a short music tip and at the same time lcd lights for roughly 2 second and goes off. Then press key to start robot . ● 5. Power on/ pause/ power off ● press key, it can pause the operation of robot and keep it stay where it is. ● press key...
Page 18
Put the robot on the charging block and keep it charging after finishing house cleaning. Do not keep the robot on pause status for long time, because under pause, the full charged battery can only last for around 20 hours. We suggest you to turn it off when you do not want it to work. Tips : the mea...
Page 19
This mode is applicable to certain area with plenty of dust. Under common circumstance, the cycle of one fixed point cleaning takes around 2 minutes. During operation, if robot continually meets obstacle or detects staircase, it would shift to avoid obstacle and staircase to turn back to work under ...
Page 20
7. Automatically charging ● ● ● ● ● ● when it finishes cleaning or there is low battery, it would seek charger in same route as automatic cleaning. To make it easy for robot to search for charging block, you need to put the block back to the wall and make sure there is no obstacle within 1.5 meters ...
Page 21
Second time setting 1. Now, the label high light, and the number with time setting is flashing. 2. Set hourandminute via and , each time press will increase one hour or minute. While decrease one hour and minute for . 3. Press again, and then go to current time setting. Set current time as 2:08 am, ...
Page 22
Note: tips : when power is off, robot will not start work on appointment time . If you have already set appointment timing cleaning, please turn on the robot and keep it on standby status， even though it is not operating. Try to make it stay at the charger and check whether it is connected. Make sur...
Page 23
10. Remote control tips: batter y placement it applies two units of alkaline batteries (7#) please note the positive and negative when place the battery change the battery when you notice it is in low battery and make sure you use the same kind of battery as mixture is forbidden. Take out the batter...
Page 24
Note: when you use virtual wall, please face marked ecovacs to the block area you expect. Put virtual wall outside of the room you want to block to get best effect. The system would cancel virtual wall after it is set for two hours in order to save battery. As a result, every time the robot start ne...
Page 25
12. Border tape usage of border tape border tape is used to confine the cleaning area. Will not proceed beyond the border, allowing to clean a designated area. Deebot deebot clean the area where you plan to paste the border tape with a dry cloth. Unroll the border tape and cut the length according t...
Page 26
13.Day-to-day storage you should keep robot stay at charger even though it finishes charging and cleaning task, because it will change to small currency to supplement charging. Charge the robot until full battery and put it back to the package if you do not need to use it for long time(at least over...
Page 27
15.Handheld vacuum cleaner ( for d76) assemble the handheld vacuum cleaner attention: press the “ handheld vacuum cleaner releasing button “ on the back of charging station and take the handheld vacuum cleaner out by grabbing the handle. Do keep the air inlet hole up to avoid dust leakage and causin...
Page 28
16. Maintenance the main unit cleaning dust box cleaning turn off the power before cleaning the host. Draw out the plug of charger before cleaning the block. Do not use petrol or oil-like to clean the surface, while you can use water or neutral detergent to scrub. Make sure you use dry cloth to wipe...
Page 29
1 7 tips： if the dust box is not placed back or not properly placed, robot will alarm and show red indicator, will show on the lcd. 1 4 1 5 1 6 hold the handle of dust box and lift it to take out. In order to avoid dust leaking, lift the suction up when you take out dust box. Please mind your speed ...
Page 30
Main br ush cleaning tips: clean the main brush after it has operated for 4 or 5 recycles. Undo the screw fixed on the main brush. Remove the hair and dust which is in-between the belt. Rip off the hair on main brush (with equipped roll brush cleaning gadget to break off the hair on main crush along...
Page 31
31 dust container cleaning dust container assembly filtration cleaning press the “handheld vacuum cleaner releasing button”on the back of charging station and take the handheld vacuum cleaner out by grabbing the handle. Do keep the air inlet hole up to avoid dust leakage and causing second pollution...
Page 32
Tap the filtration assembly gently to get rid of the attached dust. Take the sponge out of the filtration assembly. If needed , the filtration assembly can be cleaned under tap-water. Don’t use brush to clean to avoid breakage. Put the filtration assembly back to the dust container. Tips: attention:...
Page 33
Note： note: side br ush cleaning replace sidebr ush driving wheel cleaning up-ground height sensor cleaning please replace the side brush when it is destroyed. Please remove the screws, and take out the side brush. Please push the new side brush into the correct position. Tight the screws. Side brus...
Page 34
Dust sensor cleaning the dust sensor is located at the front of dust entrance. It is able to detect the concentration of dust so that it can choose efficient mode to work. We suggest you to clean dust sensor once you clean dust box to improve work efficiency. 1. Turn off power. 2. Take out dust box ...
Page 35
17. Alarm function note: the robot will stop working under following circumstance; there will be alarm and tip sound at the same time. What' s more, lcd will have red light flashing. Please notice the tip on lcd. Icon cause of failure solution instruction 1. There is too much dust in dust box. 2. Th...
Page 36
36 4 3 2 1 18. Common failure no. Problem solution robot keeps proceeding or moving backward once power is on. Turn off the power. 1. Check if there is dust on up-ground height sensor, which cause robot to make wrong signal. Use half dry cloth to clean it. Buffer collision is out of control. Put you...
Page 37
5 6 19. Other problems there is much noise when the robot works. Press the ” emo mode and the machine does not react “ d turn off the power supply, and then take out of dust box. After removing the garbage, overturn the robot. 1. Check whether the suction of main brush is blocked. 2. Examine and cle...
Page 38
. . . . . . . . . . . Cleaned for long time, as it is tangled with automatic and border cleaning mode. Its much hair and dust. Side brush can remove dust along bottom edge efficiently; there would be dust beyond 10 why does robot fail to start cleaning on robot in the tiny area formed by two walls a...
Page 39
21 how does main brush avoid being tangled 26. By power cord? Answer: robot is probably get tangled by the wire scattered on the floor when it is operating. At that time, robot will try to turn back to get rid of it, and it will make alarm sound when it fails after trying several times. 22 how can i...
Page 40
E n j o y s m a r t e r l i f e ! D7s-000im2011/02.