Summary of Deebot D54
Page 1
D54 user guide robot vacuum cleaner.
Page 2
Thanks for purchasing products hope you can enjoy it thanks again for your choice! Patented . ! Robot vacuum cleaner.
Page 3
E n j o y s m a r t e r l i f e ! Content 1. Safety instr uction. . . . User guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. Cycle c .. ..... ......... Power supply for the product. . . . . . . . . . . . . . The spectrum of product use. . . . . . . . . . . . . . Cance...
Page 4
3 do not open the equipment. The components inside the robot host are beyond repair by user himself. This product is only for domestic use, not suitable for industry or outdoor surroundings. Note： 1.Safety instruction t he user guide please conform to the basic safety precautions as follows: ● read ...
Page 5
T he spectr um of the product use ● this robot is applicable to domestic sweeping, including wooden floor, rubber floor, ceramic tile, linoleum and medium or short-haired carpet however, it is inapplicable to long-haired carpet. ● it can not be used for the floor as below: ---- have water on the sur...
Page 6
5 notes before cleaning ● take extra care of the robot when the first it works. Please remove the obstacles when it is beyond the robot. Try to avoid the situation that the robot stops working. ● make precautions to solve the problem which may make the cleaning in trouble, such as: keep the easily k...
Page 7
6 ● take good care of the product and keep it beyond child and people who can not judge danger nearby. Extra attention should be paid when it stats working. ● you should get the person inside the room know that the machine is working, in order to avoid man-made damage like tripping. ● do not take ro...
Page 8
D54 user guide robot vacuum cleaner host charging block roll brush clean-up gadget user guide 7 dc14.4v 220-240v~ dc17.5v 50hz 30w 0.7a 30w 0.25meter/second 0.7l ≤62db about 4~5 hours 45 minutes 90-120 2 m 335 × 335 × 100mm 2.8kg t he host t he charging block working voltage in-put voltage rated out...
Page 9
8 3.Name of parts control button wind gate rotating side brush up-ground height sensor all-round wheel suspended driving wheel rubber scraper on/off switch dust sensor dust sensor dust box dust box handle ash exit sponge filter lock of dust box charging and alarm indicator open button of upper cover...
Page 10
9 1.5m 0. 5m 0. 5m 1 2 3 4 5 6 7 8 9 10 control panel auto put the block at an even place and make the base perpendicular to the ground. Meanwhile, take a look at the marked electricity voltage to make sure the product is used under instruction. Placement of charging block 4.Robot charging tangle th...
Page 11
To make sure the robot is working in saturation, we suggest you to keep charging connected even though the charging indicator lasts lighting. At the same time, the system would transfer to weak current for supplementary charging. According to actual ground situation, robot can keep working for aroun...
Page 12
● press button, power is off and robot stops running. If you want the robot to stop running, you can press button under pause status. Put the robot back to the charging block after it stops working for fear that others would be tripped. Put the robot on the charging block and keep it charging after ...
Page 13
Under the auto mode, the auto indicator lights. Route description: first the robot going straight ahead, it turns when it meets obstacle. The robot will go back charging before run off the battery. ● ● if take this mode, the cleaning coverage would reach maximum compared by the same ground situation...
Page 14
7.Go back charging 13 ?? ？ ● when robot detects the low battery, it will go back charging automatically. Now, the battery indicator is yellow. You also can press button to stop the working and go back charging, and the color of the battery indicator will not change. Route description: robot will sea...
Page 15
8.Cycle cleaning 8.Cycle cleaning 14 auto auto auto set cycle cleaning cancel the cycle cleaning if you need the robot to work in the fixed time every day, please set the procedure as belowing instruction: turn on the power button, then press the button, robot will work according to the auto mode ti...
Page 16
9.Day-to-day storage 10.Maintenance 15 1 1 ● ● you should keep robot stay at charger even though it finishes charging, because it will change to small currency to supplement charging. Charge the robot until full battery and put it back to the package if you do not need to use it for long time. Keep ...
Page 17
16 tips ： if the dust box is not placed back or not properly placed. The indicator lights. 1 3 1 4 1 5 1 6 1 2 1 7 hold the handle of dust box and lift it to take out. In order to avoid dust leaking, lift the suction up when you take out dust box. Please mind your speed doing this step. Match the bo...
Page 18
17 1 1 3 4 4 4 5 1 2 8 1 9 1 2 6 7 2 main br ush cleaning tips: clean the main brush after it has operated for 4 or 5 recycles. Undo the screw fixed on the main brush. Remove the hair and dust which is in-between the belt. Put the main brush back to the host and take care of the anastomosis of belt....
Page 19
18 note： note: side br ush cleaning replace side br ush driving wheel cleaning up-ground height sensor cleaning please replace the side brush when it is destroyed. Please remove the screws, and take out the side brush. Please push the new side brush into the correct position. Tight the screws. Side ...
Page 20
19 11.Alarm function dust sensor cleaning the dust sensor is located at the front of dust entrance. It is able to detect the concentration of dust so that it can choose efficient mode to work. We suggest you to clean dust sensor once you clean dust box to improve work efficiency. 1. Turn off power. ...
Page 21
20 4 3 2 1 12.Common failure no. Problem solution robot keeps proceeding or moving backward once power is on. Turn off the power. 1. Check if there is dust on up-ground height sensor, which cause robot to make wrong signal. Use dry cloth to clean it. Buffer collision is out of control. Put your hand...
Page 22
21 5 13.Other problems there is much noise when the robot works. 1. Check whether the suction of main brush is blocked. 2. Examine and clean the main brush. 3. Examine and clean the side brush. Turn off the power supply, and then take out of dust box. After removing the garbage, overturn the robot. ...
Page 23
22 10 why robot is not charging as it is put in 17. How does main brush avoid being the charger? The charging indicator does tangled by power cord? Not light as well. Answer: robot is probably get tangled by the answer: a. Examine whether the battery at wire scattered on the floor when it is the bot...
Page 24
Enjoy smar ter life ! D54-000im201101.