Summary of WINBOT9 W930
Page 1
Fr-ca fr-ca 1 instruction manual en.
Page 2
Congratulations on the purchase of your ecovacs robotics winbot! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you with more quality time to do other things. Before you go any further, please register your product...
Page 3: Contents
1. Important safety instructions .......................................................................2 2. Package contents and technical specifications .......................................4 2.1 package contents.......................................................................................
Page 4
En en 2 en 1. Important safety instructions when using an electrical appliance, basic precautions should always be followed, including the following: read all instructions before using this appliance. Save these instructions 1. This appliance is not intended to be used by children under 8 or anyone ...
Page 5
En en 3 en 1. Important safety instructions 22. Turn off the power switch before cleaning or maintaining the appliance. 23. The plug must be removed from the receptacle before cleaning or maintaining the charging dock. 24. Remove the appliance from the charging dock, and turn off the power switch to...
Page 6: 2.1 Package Contents
En en 4 2. Package contents and technical specifications 2.1 package contents 2.2 specifications model w930 working voltage 15v dc rated power 35w remote control input voltage 3v dc power adapter：wt1503000 input：100-240v ac 50/60hz 1.6a output：15v dc 3.0a * technical and design specifications may be...
Page 7: 2.3 Product Diagram
En en 5 remote control 1. Power cord 2. Handle 3. Status indicator light and start/pause button 4. Air release trigger 5. Cleaning pad plate 6. Squeegee 7. Cupule 8. Driving treads 9. Wheel sensor 10. Bottom status indicator light 11. Bottom power switch 12. Edge detection sensors 13. Cleaning pad 1...
Page 8: 3. Operating The Robot
En en 6 3. Operating the robot 3.1 notes before cleaning do not use winbot 9 on a framed window with frame smaller than 5mm (0.2"). If winbot 9’s status indicator light flashes green after powering on, the back-up battery requires charging. Keep winbot 9 plugged in to charge the back- up battery unt...
Page 9: 3. Operating The Robot
En en 7 3. Operating the robot 3.2 attach the cleaning pad 3.4 install the safety tether turn winbot 9 over and attach the cleaning pad to the velcro smoothly. The white side of the cleaning pad attaches to the velcro, and the grey microfiber side faces out. Make sure the cleaning pad is placed exac...
Page 10: 3. Operating The Robot
En en 8 loop one end of the safety tether to end a on the robot power cord and tighten. Connect end a and end b and tighten. Loop the other end of the safety tether around the safety pod’s channel and pull it tight. 1 2 3 3. Operating the robot if the length of power cord restricts winbot 9’s moveme...
Page 11: 3.5 Place The Safety Pod
En en 9 3.5 place the safety pod 3.6 spray cleaning solution 3. Operating the robot wipe the surface of the safety pod’s suction cup with the provided finishing cloth. If winbot 9 is being used to clean an inside window: press the safety pod firmly on the top corner of the inside window. Make sure t...
Page 12: 3. Operating The Robot
En en 10 3. Operating the robot 3.7 start plug in winbot 9 place on the glass power on 1 3 2 move the bottom power switch to the “ ” position. Winbot 9 is powered on when it beeps and the status indicator light flashes blue. Please ensure there is a 15cm (5.9”) clearance between the glass and obstac...
Page 13: 3.8 Pause
En en 11 3.8 pause pause winbot 9 during cleaning by pressing the start/pause button on the robot or on the remote control. Winbot 9 can be directed to move forward, backward, left and right using the direction control buttons on the remote control when paused. Winbot 9 will clean when direction con...
Page 14: 3.9 Stop
En en 12 remove winbot 9 power off move the power switch to the “o” position. Grasp winbot 9’s handle. Pull the air release trigger and remove winbot 9 from the window. Polish away any marks left on the glass from winbot 9’s removal with the provided finishing cloth. 1 2 3.9 stop when winbot 9 compl...
Page 15: 4. Maintenance
En en 13 4. Maintenance turn the robot over and remove the cleaning pad. Soak the cleaning pad in cool, clean water for 2 minutes. Hand wash with mild detergent and lay flat to dry. Allow the cleaning pad to dry completely before re-attaching it to the robot. Before performing cleaning and maintenan...
Page 16: 4. Maintenance
En en 14 4. Maintenance cleaning winbot 9’s corners turn the robot over, remove the cleaning pad and wipe the four corners of winbot 9 with the provided finishing cloth. Edge detection sensors turn the robot over and wipe the four edge detection sensors clean with the provided finishing cloth to mai...
Page 17: 4. Maintenance
En en 15 4. Maintenance move the bottom power switch to the “ ” position. Inspect the driving treads by using the and buttons on the remote control. Stop the driving treads if dirt is seen on the treads. Move the bottom power switch to the “o” position. Clean any dirt on the driving treads with the ...
Page 18
En en 16 5. Status indicator light and sounds indicator description status indicator light flashes green back-up battery is low and is charging. Winbot 9 will not clean until the back-up battery is properly charged. Status indicator light flashes blue winbot 9 is powered on. If winbot 9 is already o...
Page 19: 6. Troubleshooting
En en 17 6. Troubleshooting no. Malfunction possible causes solutions 1 remote control does not work. Winbot 9 is cleaning. When winbot 9 is cleaning, only the start/ pause button works on the remote control. Pause winbot 9 by pressing the start/ pause button on the robot or remote control. Other bu...
Page 20: 6. Troubleshooting
En en 18 6. Troubleshooting no. Malfunction possible causes solutions winbot 9 has encountered a problem. A. Press the reset button on the remote control. B. Check for stubborn stains on the window. Clean the stains before using winbot 9. C. Check the cupule for dirt or damage. Clean the cupule as d...
Page 21
En en 19.
Page 22
Winbot 9-018-im2014r02 designed and manufactured by/conception et fabrication par distributed by/distribué par made in china/fait en chine canton, oh, usa/canton, oh, É.-u. Ecovacs robotics, co., ltd. Ecovacs robotics, inc..