1. DL manuals
  2. EcoWater
  3. Water System
  4. ESD 2502R30
  5. Owner's Manual

EcoWater ESD 2502R30 Owner's Manual

Other manuals for ESD 2502R30: Owner's Manual
Manual is about: EcoWater electronic demand water system

Summary of ESD 2502R30

  • Page 1

    1 owner’s manual how to maintain and operate your ecowater electronic demand water system r model esd 518 models esd 2502r30 esd 2502r39 systems tested and certified by nsf international and wqa against nsf/ansi standard 44 for softener performance. Printed in usa part no. 7277268 (rev. D 11/17/05) ...

  • Page 2: Guarantee

    2 limited warranty ecowater systems llc advantage warranty series esd 518, esd 2502r30 & esd 2502r39 water systems congratulations! You have just purchased the highest quality water conditioning product on the market. To register your warranty, com- plete the enclosed warranty registration card and ...

  • Page 3

    3 safety guides follow the installation instructions carefully. Failure to install the ecowater softener properly voids the war- ranty. Before you begin installation, read this entire manual. Then, obtain all the materials and tools you will need to make the installation. Check local plumbing and el...

  • Page 4

    4 dimensions / specifications in out 32--- 1/2” in --- out 14” 20” in --- out 14” 14” c b 16” 16” 36--- 9/16” 32” esd 518 in out a esd 2502r30 esd 2502r39 a b c model nominal resin tank size a b c esd 518 8” dia. X 35” 3---3/8” 38--- 1/8” 45” esd 2502r30 8” dia. X 40” 3---3/8” 41.6” 48.75” esd 2502r...

  • Page 5

    5 installation -- (models esd 518 & esd 2502r30) (esd 518 shown) figure 1 floor drain floor drain note: faceplate and support not shown for clarity of drawing. Tie or wire valve drain hose in place, to keep over floor drain. Valve drain hose valve drain hose brine tank overflow hose brine tank overf...

  • Page 6

    6 installation (continued) -- (models esd 518 & esd 2502r30) 5. Install inlet and outlet adaptors, or the optional bypass valve. Important: be sure the turbine, turbine support and sensor housing are firmly in position, in or on the valve outlet. H inlet and outlet adaptors --- push adaptors into th...

  • Page 7

    Figure 4 figure 5 bypass valve inlet valve outlet valve valve inlet soft water hard water hard water to outside faucets outlet bypass valve clip (2) clip (2) inlet copper tubes (install in soft- ener valve or bypass valve) soldered copper, threaded, or pvc plastic pipe and fittings. Plumb to copper ...

  • Page 8

    8 installation (continued) -- (model esd 2502r39) 4. Run the valve and brine tank overflow drain hoses (figure 6). Secure the valve drain hose to the drain fit- ting with the included hose clamp. Provide a mini- mum 1---1/2” air gap at the floor drain, standpipe, laundry tub, or other approved drain...

  • Page 9

    9 down keypad up keypad display select keypad recharge keypad figure 7 when the transformer is plugged in, a model code shows in the face plate display for the first few seconds. The model code for your water softener is s518, s30 or h40, as shown in the following drawing. The model code is fol- low...

  • Page 10

    10 3. Set recharge (regeneration) time: press the select keypad once to display 2:00 am (flashing) and recharge time. At the 2:00 am recharge time set- ting, the softener begins regeneration at 2:00 am, ending no later than 4:00 am. This is a good time in most house- holds because water is not being...

  • Page 11

    11 extra recharge sometimes, a manually started regeneration (recharge) may be desired, or needed. Two examples are: . You have used more water than usual (guests visiting) and you may run out of soft water before the next timer started regeneration. . You did not refill the softener with salt befor...

  • Page 12

    12 refilling with salt remove the brine tank cover and check the salt storage level frequently. If the unit uses all the salt before you refill it, you will get hard water. Until you have established a refilling routine, check the salt every 2 or 3 weeks. Al- ways refill if less than 1/2 full. Be su...

  • Page 13

    13 resin bed cleaning if the water supply contains ‘‘clear water ’’ iron (see page 9), regular resin bed cleaning is needed to keep the bed from coating with iron. Use resin bed cleaner, available from ecowater, following directions on the container. Clean the resin every 6 months, or more often if ...

  • Page 14

    14 repair parts -- all models 1 2 valve assembly (see pages 16 --- 19 ) 6 3 4 5 7 8 9 10 11 12 13 14 15 17 16 17 18 8 5 2 28 16 9 41 10 11 12 13 14 15 27 26 25 24 23 37 22 21 20 19 36 35 34 33 32 31 30 29 40 39 38.

  • Page 15

    15 repair parts -- all models key no. Part no. Description 1 7252373 transformer, 24v---10va 2 7218662 top cover (esd 518) 7218670 top cover (esd 2502 models) 3 7210509 faceplate (order following decal) --- 7214692 decal 4 7238418 repl. Pwa 5 7211173 faceplate support 6 7210389 salt hole cover (esd ...

  • Page 16

    16 repair parts -- esd 518 & esd 2502r30 51 1 2 4 3 5 6 7 8 9 10 11 12 13 14 15 16 17 21 20 19 18 23 27 28 44 43 31 30 29 32 33 34 35 36 37 39 40 41 42 46 47 48 49 24 cross---section view seal wear---strip 25 26 50 22 45 52 38.

  • Page 17

    17 repair parts -- esd 518 & esd 2502r30 key no. Part no. Description 1 7224087 screw, #8-32 x 1” (2 req.) 2 7228544 motor (incl. 2 ea. Of key no. 1) 3 0900857 screw, #6-20 x 3/8 (2 req.) 4 7231385 motor plate 5 0503288 bearing 6 7113927 cam and gear 7 7142942 clip (drain) 8 0900431 tubing clamp 9 7...

  • Page 18

    18 repair parts -- esd 2502 r39 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 cross---section view seal wear---strip 48 47 8.

  • Page 19

    19 repair parts -- esd 2502 r39 key no. Part no. Description 1 7224087 screw, #8-32 x 1” (2 req.) 2 7228544 motor (incl. 2 ea. Of key no. 1) 3 7231393 motor plate 4 0900857 screw, #6-20 x 3/8 (3 req.) 5 7171250 bearing 6 7219545 cam and gear 7 7169180 clip (drain) 8 0900431 hose clamp 9 7271270 drai...