ECX Revenge ECX04000 Type E Instruction Manual

Manual is about: 1/8 Electric Buggy

Summary of Revenge ECX04000 Type E

  • Page 1

    Instruction manual bedienungsanleitung manuel d’utilisation manuale di istruzioni 1/8 electric buggy ecx04000 congratulations on your purchase of the ecx ® revenge type e ™ buggy. This 1/8-scale model introduces you to the sport of rc driving. Herzlichen glückwunsch zum kauf des ecx revenge type e b...

  • Page 2: Table Of Contents

    En notice all instructions, warranties and other collateral documents are subject to change at the sole discretion of horizon hobby, llc. For up-to-date product literature, visit http://www.Horizonhobby.Com and click on the support tab for this product. Warning: read the entire instruction manual to...

  • Page 3

    En 3 water-resistant vehicle with waterproof electronics your new horizon hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions”, including puddles, creeks, wet grass, snow and even rain. ...

  • Page 4: Vehicle Preparations

    En 4 transmitter frequency 2.4ghz modulation dsm, dsm2, marine battery aa x 4 servo power supply 4.8v~6v (shared with receiver) output torque 199.8 oz-in (8.5 kg-cm) operating speed 0.20 sec/60 degrees of travel size 55.6 x 18 x 30mm electronic speed control (esc) input voltage 7.4–11.1v constant/pe...

  • Page 5

    En 5 installing the wing 1. Remove the long wing clip from the wing mounts. 2. Align the holes in the wing with the wing mounts. 3. Press the wing onto the wing mounts. 4. Secure the wing by sliding the long wing clip through the wing mounts. Installing the battery in the vehicle removing/installing...

  • Page 6

    En 6 transmitter controls bind th st n r n r power st. Trim th. Trim st. Rate reverse switch allows you to change the direction of steering (st. Rev) and throttle (th. Rev) controls. (default settings are “r” for steering and “n” for throttle) bind th st n r n r adjusts the neutral point of the elec...

  • Page 7: Operation

    En 7 getting started 2. Connect the battery and turn on the esc. 3. Do a test of the transmitter’s control of the vehicle with the vehicle’s wheels off the ground. Power st. Trim th. Trim st. Rate 1. Power on the transmitter. • always turn on your transmitter before you turn on the receiver in the v...

  • Page 8: When You Are  Finished

    En 8 when you are finished • prolong motor life by preventing overheating conditions. Undue motor wear results from frequent turns, stops and starts, pushing objects, driving in deep sand and tall grass, and driving continuously up hill. • over-temperature protection is installed on the esc to preve...

  • Page 9

    En 9 electronic speed control (esc) the esc comes preset from the factory. It will need to be recalibrated whenever changing to a different transmitter. Esc calibration procedure ensure proper esc function by calibrating the esc to your transmitter inputs. 1. Power off the esc. 2. Ensure your transm...

  • Page 10

    En 10 additional maintenance tips • examine your vehicle on a regular basis. • use a brush to remove dirt and dust. • look for damage to the suspension arms around other molded parts. • re-glue the tires to the wheels, if necessary. • use suitable tools to check and tighten fasteners. • make sure th...

  • Page 11: Limited Warranty

    En 11 limited warranty what this warranty covers horizon hobby, llc (horizon) warrants to the original purchaser that the product purchased (the "product") will be free from defects in materials and workmanship at the date of purchase. What is not covered this warranty is not transferable and does n...

  • Page 12

    En 12 contact information country of purchase horizon hobby contact information address united states of america horizon service center (repairs and repair requests) servicecenter.Horizonhobby.Com/ requestform/ 4105 fieldstone rd champaign, illinois, 61822 usa horizon product support (product techni...

  • Page 13: Fcc Information

    En 13 compliance information for the european union this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may...