1. DL manuals
  2. Edco
  3. Saw
  4. BB14E
  5. Operator's Manual

Edco BB14E Operator's Manual

Manual is about: gasoline and electric 14" masonry saws

Summary of BB14E

  • Page 1

    Operator’s instruction manual masonry saws gasoline and electric 14” masonry saws e-bb14e&bb14g-i-0416 e-spts-i-0809 equipment development co., inc. Equipment development co., inc. 100 thomas johnson drive, frederick, md 21702-4600 usa phone: 301-638-3326 • 301-663-1600 fax: 800-447-3326 • 301-663-1...

  • Page 2

    Page 2 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Read and understand the operators instruction manual thoroughly before attempting to operate this equipment. Death or serious injury could occur if this machine is used improperly. Extreme care...

  • Page 3

    Page 3 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. How to order repair parts to insure product safety and reliability, always use genuine edco replacement parts when making repairs to the equipment. When ordering parts, please spe...

  • Page 4

    Page 4 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Operator controls - gas models bb14 gas (figure 2) a air filter b. Fuel tank c. On/off switch d. Water pump belt guard e. Oil dip stick f. Handle g. Blade guard h. Water tray plug i. Rolling ta...

  • Page 5

    Page 5 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. J bb14 electric (figure 4) a. Operating handle b. Motor c. Reset button d. Power cord e. Water pick up hose f. Water tray plug g. Rolling table h. Welded steel frame/water tray i....

  • Page 6: Safety Guidelines

    Page 6 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Safety guidelines safety warnings and guidelines do not by themselves eliminate danger. They are not substitutes for proper accident prevention procedures and good judgement. Read and understan...

  • Page 7: Operating Instructions

    Page 7 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Before starting: • read and understand the instructions supplied by the engine manufacturer. • familiarize yourself with all engine and saw controls. (figure 2) • visually inspect...

  • Page 8

    Page 8 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. When wet cutting: • secure the drain plug and fi ll the tray with clean water. On gasoline models: • to engage water pump loosen the black knob and lightly push top of water pump to the left wi...

  • Page 9

    Page 9 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. When dry cutting: • drain and fl ush any water or debris in the tray and dispose of properly. On gasoline models: • to disengage water pump loosen the black knob and push top of w...

  • Page 10

    Page 10 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Figure 15 (bb14g) starting the engine: • be sure blade is clear of item to be cut. • determine that the recoil starter assembly turns freely, starter rope pulls easily, and the rope retracts p...

  • Page 11

    Page 11 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Cutting: • do not strain the engine/motor while cutting. Do not jam work piece into the blade. Do not twist the work piece while cutting. • when you have fi nished cutting: on ga...

  • Page 12: Maintenance

    Page 12 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Disconnect spark plug lead before performing any maintenance on this machine. Changing the blade: • inspect the new blade thoroughly before installing. Check for cracks, loose or missing segme...

  • Page 13

    Page 13 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Belt adjustment and replacement: • periodically check belt(s) for damage, same type and are at the proper tension. Do not mix belts. Slipping belt(s) will overheat causing the cu...

  • Page 14

    Page 14 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Clean and lubricate wheels on rolling table: • during daily visual inspection, check to be sure the wheels on both sides of the rolling table move smoothly and that there is no debris in the w...

  • Page 15: Maintenance Schedule

    Page 15 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Repairs are to be preformed by edco or by approved edco repair technicians. Read and follow all instructions in the engine manufacturer’s owner’s manual. Maintenance schedule *ga...

  • Page 16

    Page 16 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Notes ________________________________________________________________ ________________________________________________________________ ________________________________________________________...

  • Page 17

    Page 17 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Notes ________________________________________________________________ ________________________________________________________________ __________________________________________...

  • Page 18: Smi Dust and Silica Warning

    Page 18 e-bb14e&bb14g-i-0416 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as res...

  • Page 19

    Page 19 e-bb14e&bb14g-i-0416 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Limited equipment warranty of sale – terms & conditions equipment development company, inc. Herein referred to as edco (seller) warrants that each new unit manufactured by edco t...

  • Page 20

    E-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Surface preparation, resoration, professional sawing equipment & hand held tools 100 thomas johnson drive, frederick, md 21702 phone: 800-638-3326 or 301-663-1600 fax: 800-447-3326 or 301-663-1607 email: sal...