1. DL manuals
  2. Edco
  3. Floor Machine
  4. SEC-NG
  5. Operator's Instruction Manual

Edco SEC-NG Operator's Instruction Manual

Manual is about: SINGLE-DISC FLOOR GRINDER

Summary of SEC-NG

  • Page 1

    Operator’s instruction manual single-disc floor grinder sec-ng secng-i-1217 e-spts-i-0809 equipment development co., inc. Equipment development co., inc. 100 thomas johnson drive, frederick, md 21702-4600 usa phone: 301-638-3326 • 301-663-1600 fax: 800-447-3326 • 301-663-1607 edcoinc.Com • techsuppo...

  • Page 2

    Page 2 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Read and understand the operators instruction manual thoroughly before attempting to operate this equipment. Death or serious injury could occur if this machine is used improperly. Extreme care m...

  • Page 3: Table of Contents

    Page 3 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Table of contents safety and warnings .................................................................................................................................................

  • Page 4

    Page 4 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. How to order repair parts to insure product safety and reliability, always use genuine edco replacement parts when making repairs to the equipment. When ordering parts, please specify the model a...

  • Page 5

    Page 5 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Read and understand all operating instructions before operating this equipment. Death or serious injury can result if this machine is used improperly. Eye and ear protection must b...

  • Page 6: Operating Controls

    Page 6 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Operating controls please note: controls shown are for the model indicated. The location of these controls may vary on the different models. Due to improvements and changes in the equipment, the ...

  • Page 7: Operating Instructions

    Page 7 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Operating instructions 1. Loading tools: lean the machine back on the handle to expose the work area and load the proper tools for your job. Electric machines should be unplugged. ...

  • Page 8

    Page 8 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Getting started with your new grinder begin the leveling process: check level of floor. Begin the leveling process: lower machine to surface and match level. Adjust height by turning leveling han...

  • Page 9

    Page 9 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Getting started with your new grinder leveling: lean back slightly on the handle to get the tools off the surface and start the machine. Lower the machine to the surface and do a s...

  • Page 10

    Page 10 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Getting started with your new grinder leveling: the bubble on the machine will not necessarily be centered once optimum operating position is achived. It will also float back and forth during gr...

  • Page 11: Operating Instructions

    Page 11 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Operating instructions • before starting the motor: raise the front of the machine clear of the working surface. • start motor and allow it to reach operating speed: position the ...

  • Page 12

    Page 12 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Attaching a vacuum / servicing head assembly procedure for attaching a vacuum: if using a vacuum for dust control attach it to the vacuum port at the rear of the machine which is on the handle a...

  • Page 13

    Page 13 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. For use with quick-change multi-accessory disc double dyma-dots: general purpose grind - removes general purpose epoxy, mastics, thinsets, water-proofing coatings and more. Single...

  • Page 14: Maintenance Instructions

    Page 14 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Maintenance instructions 1. Disconnect the machine from the power source. Disconnect the supply voltage connector at the machine on electric models before performing any maintenance. All mainten...

  • Page 15: Maintenance Schedule

    Page 15 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Quick reference for maintaining grinders before operation every 4 hours daily every 50 hours of operation as required visual inspection of entire machine x check engine oil* x che...

  • Page 16

    Page 16 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respi...

  • Page 17

    Page 17 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Msslr-0117 printed in usa ©2017 page 1 machine safety symbol label reference this symbol means that the operator’s, owners, instruction and/or manufacturer(s) manuals must be read...

  • Page 18

    Page 18 secng-i-1217 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Msslr-0117 printed in usa ©2017 page 2 this symbol means that the machine is heavy if the machine needs to be lifted onto or off of a truck, loading dock etc. That proper technique or heavy duty...

  • Page 19

    Page 19 secng -i-1217 e-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Limited equipment warranty of sale – terms & conditions equipment development company, inc. Herein referred to as edco (seller) warrants that each new unit manufactured by edco to...

  • Page 20: Before Using This Product

    E-spts-i-0809 800-638-3326 • edcoinc.Com • techsupport@edcoinc.Com equipment development co., inc. Scan this qrc or visit www.Edcoinc.Com/customer-support read : edco owner’s manuals and parts listings share basic information and parts of each product. Download and print them whenever needed. Watch:...