1. DL manuals
  2. Edco
  3. Saw
  4. SS-24
  5. Operator's Instruction Manual

Edco SS-24 Operator's Instruction Manual

Manual is about: SELF PROPELLED CONCRETE / ASPHALT SAW

Summary of SS-24

  • Page 1

    Operator’s instruction manual ss-24 self propelled concrete/asphalt saw ss24-i-0215 e-spts-i-0809 equipment development co., inc. Equipment development co., inc. 100 thomas johnson drive, frederick, md 21702-4600 usa phone: 301-638-3326 • 301-663-1600 fax: 800-447-3326 • 301-663-1607 edcoinc.Com • s...

  • Page 2

    Page 2 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Read and understand the operators instruction manual thoroughly before attempting to operate this equipment. Death or serious injury could occur if this machine is used improperly. Extreme care must be ...

  • Page 3

    Page 3 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Note: dimensions are approximate b c d e a f operator’s instruction manual ss-24 table of contents safety guidelines ..........................................................................

  • Page 4: Safety Guidelines

    Page 4 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Safety guidelines maintain a safe operating distance from fl ammable materials. Sparks from the cutting-action of this saw can ignite fl am- mable materials or vapors. Operator must wear appropriate clo...

  • Page 5: Operating Instructions

    Page 5 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. J operating instructions figure 2 3 ignition 5 blade saver switch itch 11 hour meter 12 handle locks e 10 clutch 10 9 speed control s 12 handle locks h 1 emergency stop (e-stop) em 14 guid...

  • Page 6

    Page 6 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Before starting the engine: • read rx for concrete saws before operating. • inspect machine before each use according to the maintenance schedule on page 15. • locate and be familiar with all engine and...

  • Page 7

    Page 7 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. For dry cutting: consult blade manufacturer for maximum depth of cut. Starting and controlling the cut: • engine must be at full throttle. • move clutch lever to drive position and adjust ...

  • Page 8

    Page 8 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. To stop cutting: • move speed control lever to the neutral position. • turn depth control handwheel clockwise until blade is clear of slab. • push clutch lever forward, away from operator to the free wh...

  • Page 9: Maintenance

    Page 9 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Maintenance should the engine stop while operating: • check water supply: a. Is city water valve fully open? B. Is valve on saw console open? C. If you are using gravity feed, check the fl...

  • Page 10

    Page 10 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Changing blades: • raise blade guard and remove arbor shaft cap screw, lock washer and blade retaining cap. (figure 14) to remove the arbor shaft cap screw use a 3/4” wrench. • clean the arbor shaft, b...

  • Page 11: Important!

    Page 11 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Grease bearings - (7 total) arbor shaft bearings (2) must be greased every 4 hours. All other bearings (5) must be greased every 40 hours. Those include: rear wheel bearings (2), drive ax...

  • Page 12

    Page 12 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Check engine oil before each operation - check engine manufacturer’s owner’s manual for specifi c instructions. Change oil & filter every 50 hours of operation (sooner if necessary). Check drive chains...

  • Page 13

    Page 13 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Changing to left-side cutting: • disconnect water hose from the blade guard. • • using sae 9/16” and 3/4” wren using sae 9/16” and 3/4” wrenches, remove the bolts on the blade guard. • on...

  • Page 14

    Page 14 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Inspect transmission fluid level every 50 hours of operation - fi ll as required. The fi ll level line is located on the fi ll spout. Fill using gm dexron b or comparable fl uid. Replace fuel filter as...

  • Page 15: Maintenance Schedule

    Page 15 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. *gasoline models only maintenance schedule repairs are to be done by authorized edco dealers only. Read and follow instructions in the engine manufacturer’s manual x x x x x x x x visual ...

  • Page 16

    Page 16 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Notes ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ...

  • Page 17

    Page 17 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Notes ________________________________________________________________ ________________________________________________________________ ___________________________________________________...

  • Page 18: Smi Dust and Silica Warning

    Page 18 ss24-i-0215 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory ...

  • Page 19

    Page 19 ss24-i-0215 e-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Limited equipment warranty of sale – terms & conditions equipment development company, inc. Herein referred to as edco (seller) warrants that each new unit manufactured by edco to be free...

  • Page 20

    E-spts-i-0809 800-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development co., inc. Surface preparation, restoration, professional sawing equipment & hand held tools 100 thomas johnson drive, frederick, md 21702 phone: 800-638-3326 or 301-663-1600 fax: 800-447-3326 or 301-663-1607 email: sa...